Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Erie
Gate hinge replacement in Erie typically runs $220-$480, while a full post replacement with on-site welding lands between $650 and $1,400 depending on footing depth and HOA finish requirements. We get most parts and welding jobs done same week, and Hal Gatewood answers the phone himself at (877) 610-2993 any hour you call. This page is for Erie homeowners who are done fighting a sagging gate and want someone who actually shows up with a welder in the truck, not a sales pitch.
Erie’s open Front Range plains at 5,000 feet produce some of the most aggressive sustained winds in the metro area. Those westerly gusts and Chinook events don’t just push a gate around. They fatigue hinges, pull posts off plumb, and strip the plastic gear racks inside builder-grade operators. We’ve been welding and repairing gates here since 2001, and we know exactly which parts fail first in this wind. Our shop is down the road, the owner’s name is on every invoice, and we stand behind every job with a written 90-Day Done Right Promise.
Why Gatewood Fence & Gate Is Erie’s Preferred Gate Parts & Welding Company
Hal Gatewood has been owner-operated since 2001. His name is on the shop, his license number is published, and he still shows up on job sites in Erie to look at the gate himself. When a company’s owner lives in the work, the work gets done differently. You aren’t getting a rotating crew of subcontractors. You’re getting Hal or someone trained under him, background-checked and uniformed, who knows what an HOA architectural committee in Colliers Hill expects before a single weld gets struck.
Erie homeowners don’t need a company that wants to sell them a whole new gate. They need a repair-first shop that will cut out a failed hinge post, weld in a proper replacement, and match the powder coat to the HOA’s approved finish code. That’s what we do. We’ve done it in Flatiron Meadows, Erie Commons, and Colliers Hill dozens of times. Our Gate Parts & Welding work carries one promise: if it’s not done right within 90 days, one call brings us back. No runaround, no fine print.
Our crew runs calls into Erie daily. If you’re near Erie Parkway or County Line Road, we can usually get eyes on your gate the same day you call. You won’t reach a voicemail tree. A live person picks up, every time, 24/7.
Our Gate Parts & Welding Services in Erie
Hinge Replacement
Wind-driven fatigue kills hinges in Erie faster than anywhere else in the county. A standard barrel hinge replacement on a decorative steel or aluminum gate runs $180-$340, including parts and on-site welding if needed. When the hinge is welded to a post that’s begun to lean, we don’t just swap the hinge. We check the post footing and reinforce it so the new hinge isn’t fighting the same wind with a weaker anchor. Hinge replacement on a sagging gate without checking the post is a temporary patch.
Post Replacement
The most common call we get from Erie subdivisions is a gate post that’s pulled loose at the footing. Builder-installed posts in Colliers Hill and Flatiron Meadows often lack reinforcement plates, and five to ten years of 50 mph gusts will wobble them right out of the dirt. Post replacement in Erie runs $650-$1,400, depending on footing depth, concrete, and whether the HOA requires a specific powder coat finish. We handle the architectural committee paperwork for you, so the job doesn’t stall waiting on an approval letter.
Rail Repair
When an ornamental iron gate sags, the top rail usually pulls away from the hinge side. That’s a weld fracture, not a bolt issue. We cut out the cracked section, weld in a patch or a new rail, and grind it smooth before finishing to match the existing color. Rail repair on a standard residential double gate in Erie runs $280-$620. Fix the panel without addressing why it cracked and you’ll fix it twice.
Custom Welding
Sometimes the gate that’s there isn’t the gate you need. You may have a manual gate installed during Erie’s 2000s-2020s building boom that was never prepped for automation. Or a steel frame that keeps twisting under wind load. We weld on-site, in your driveway, so the gate never leaves your property. Custom welding jobs in Erie start around $350 for brackets and reinforcement work, and go up from there based on material and finish requirements. Hal has been welding since 2001 and prefers to fix the gate in front of you rather than haul it off and return a different-looking gate two weeks later.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Erie
We’re certified to service nine major gate brands, including FAAC, BFT, and Linear operators that show up regularly in Erie’s master-planned communities. Whether you have a LiftMaster swing arm or a Viking ram, we stock replacement racks, hinges, control boards, and safety edges locally, so your repair doesn’t wait on a week-long parts shipment. Erie’s uniform housing stock means we can keep the specific parts your neighborhood’s gates use on hand and ready. If your operator’s plastic gear rack stripped during a windy stretch, we can usually have the new one in and adjusted the same week.
Common Gate Parts & Welding Problems We See in Erie Homes
- Builder-grade operators failing under sustained wind: Erie’s 2000s-2020s construction boom put a lot of cheap operators on ornamental iron gates. Two or three years of 50 mph gusts and the plastic gear racks strip, the hinges twist off plumb, and the gate starts grinding instead of swinging. We replace the rack with metal where possible and reinforce the hinge mount.
- Manual gates with no conduit or power run: Many newer homes in Erie have manual gates that were installed without electrical conduit. Adding automation later means trenching through frozen clay or HOA-landscaped beds. We can run the power and install the operator without wrecking your yard, and we’ll document the route for the HOA.
- Wind-driven sag at the hinge post: The sag almost always starts at the hinge post, not the middle of the panel. Homeowners tighten hinges or shim the latch, but the footing keeps loosening. We weld in a reinforced 3×3 steel post, deepen the footing, and add a sag correction bracket so the gate swings clean even when the wind hits hard.
- Powder coat damage from hailstorms and freeze-thaw: Erie catches spring hailstorms that chip powder coat, and the freeze-thaw cycle gets under the finish and starts rust. We repair the weld and then match the coating to your HOA’s approved color. If you’re in Erie’s 80516 ZIP, we know the finish codes for the big subdivisions already.
Pricing for Gate Parts & Welding in Erie, CO
Here’s what Erie homeowners can expect to pay for the common repairs we handle:
- Hinge replacement: $220-$480
- Post replacement with on-site welding: $650-$1,400
- Rail repair and reinforcement: $280-$620
- Custom welding or sag correction bracket: $350-$900
- Adding automation to a manual gate (including power run): $1,200-$3,800 depending on trenching and operator
Every price is quoted and agreed to in writing before any work starts. You’ll never get a door-shock invoice. We also stand by our standing offers: $40 off any repair over $200, free second opinions on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and tell us what your gate is doing. We’ll tell you over the phone what it likely costs to fix it.
We Also Serve Cities Near Erie
While this page is written for Gate Parts & Welding in Erie, our crews regularly run to Lafayette, Louisville, Gunbarrel, and Frederick for the same gate repairs. If you’re just over the county line and wondering whether we’ll come out, the answer is yes. Same live person answering the phone, same written promise, same on-site welding.
Serving Erie, CO - Our Local Coverage Area
We’re based in the Erie area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Erie
Because the hinge post is pulling loose at the footing, not the hinge bolts. Erie’s sustained westerly winds rock the post back and forth every time a gust hits, and builder-installed posts in the 2000s-2020s subdivisions usually don’t have deep enough footings or reinforcement plates. Tightening the hinges fights the symptom. Welding in a new post with a deeper footing and a sag correction bracket fixes the cause. In Colliers Hill and Flatiron Meadows, this is the single most common repair we make. Call (877) 610-2993 and we’ll come look at the footing, not just the hinges.
Usually yes. Most manual gates in Erie’s newer developments weren’t pre-wired for power, but we can trench a clean conduit line through the lawn and flower beds with minimal disruption. The job typically runs $1,200-$3,800, depending on how far the trenching has to go and which operator you choose. We stock linear actuators and swing arm openers from brands like BFT and FAAC for the common Erie gate styles. We’ll also file the paperwork with your HOA’s architectural committee so the power run and operator are documented to their specs. Estimates are free.
In most of Erie’s master-planned subdivisions, yes. Many covenants in Colliers Hill, Flatiron Meadows, and Erie Commons require written architectural committee approval before swapping hardware or repainting a gate, even for a hinge or a post. We pre-document the approved finish codes and submit the paperwork for you, which is typically the difference between a one-week repair and a three-week stall. We’ve done enough HOA work in Erie to know exactly what the committees look for, and we write the submission the first time so it gets approved the first time.
Because most builder-grade LiftMaster operators installed during Erie’s housing boom use plastic gear racks that can’t take sustained 50 mph wind load. When the wind grabs a heavy ornamental iron gate, the plastic strips under the repeated stress. We replace the stripped rack with a metal gear where the operator allows it, then set the force limits and close speeds to match Erie’s wind conditions, not the factory defaults. If the rack has stripped, don’t keep cycling the operator. Call us at (877) 610-2993 before the stripped gear takes the control board with it.
Yes, but it takes care. We cut out the failed post, weld in the new one, and then grind and finish the weld area to match. We re-powder coat the affected section to your HOA’s exact finish code, which we already have on file for most Erie subdivisions. The heat from welding can discolor the surrounding finish, so we mask and shield the nearby rails. When we’re done, the repair blends. A repair that matches the approved black finish means the HOA won’t have anything to flag, and you get a gate that swings true again.
Call (877) 610-2993 now. Hal or one of his crew will answer, ask what the gate is doing, and tell you straight what it’ll take to fix it. Free estimates, written pricing before any work, and a live person on the line every time you call.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Erie since 2001.