Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across El Reno
Gate parts and welding in El Reno usually comes down to one question: can the gate be saved, or is it time to start over? Most of the time, the gate can be saved. We weld on site, in your driveway or pasture, and we’ve been doing it that way since Hal Gatewood opened the shop in 2001. When a 16-foot pipe gate gets bent by wind-thrown debris off US-270, you don’t haul it to a shop. You call someone who brings the welder to you. That’s what we do. If you’ve got a sagging hinge post, a snapped rail, or a latch that hasn’t lined up since the last big storm, call (877) 610-2993 and a live person answers. Day or night.
Why Gatewood Fence & Gate Is El Reno’s Preferred Gate Parts & Welding Company
We’re not a franchise outfit that shows up in a wrapped van and leaves you with an 800 number. Hal Gatewood’s name is on the shop, and the shop is a short drive from El Reno. When we weld a gate in El Reno, the person who did the work is the person you’ll see at the hardware store next month. That’s the oldest accountability there is.
El Reno customers don’t have to wonder who’s coming. Our crew is background-checked and uniformed. The phone gets answered by a person, 24 hours a day. No voicemail. No phone tree. If a cattle gate goes down at 11 p.m. and your herd is standing there looking at an open pasture, you call, Hal answers, and we get there.
We also stand behind the work in writing. Every job carries the 90-Day Done Right Promise. If it’s not done right, we make it right. Not a pro-rated apology. Not a three-week callback window. One call and the same crew returns.
Our Gate Parts & Welding Services in El Reno
Hinge Replacement
Most El Reno gate problems start at the hinge post, not the middle of the gate. A gate sags in the hinge post, not in the middle, and that’s where we start. The expansive clay soils throughout Canadian County heave and lean posts seasonally. We see hinge plates wallowed out, pins worn thin, and posts leaning just enough that the latch misses by half an inch. We replace hinges with heavier barrel hinges, add grease fittings where it makes sense, and reset the post if it’s moved. Fix the panel without the post and you’ll fix it twice.
Post Replacement
El Reno’s clay soil doesn’t hold posts the way people expect. It swells when it’s wet and shrinks when it’s dry, and over ten or twenty years a hinge post can lean enough to drag a gate. We dig out the old post, set the new one deeper than the original, add gravel drainage at the base, and concrete it in. On heavy pipe gates for cattle pens and pasture entries, we’ll often size up the post. A gate sized for trucks and trailers needs more post than a decorative suburban walk gate, and we’ve seen plenty that were undersized from day one.
Rail Repair
Rail repair covers the horizontal members of the gate frame. In El Reno, wind-thrown debris from severe storms is the usual culprit. A cedar post or a chunk of fence panel comes through at 80 miles an hour and bends a schedule 40 top rail into a question mark. We cut out the damaged section, weld in a replacement, and brace it where the original design was weak. If the gate was underbuilt for the wind load it actually faces, we’ll tell you that too, and price a reinforcement rather than a patch.
Custom Welding
Custom welding is where we earn our keep in El Reno. Not every repair fits a catalog part. A cattle-pen swing gate with a bent frame, a pasture entry that needs a wider opening for a new tractor, a section of steel pipe fence that a truck backed into. We weld on site, with a truck that carries the gear. No hauling gates to a shop across town. You tell Hal what’s bent, broken, or missing, he’ll look at it, and he’ll tell you straight whether it’s worth welding or cheaper to replace.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in El Reno
We’re certified to service nine major gate brands, and in El Reno we regularly work on Linear, Ghost Controls, and DoorKing operators. If your automatic gate opener has a board that fried after a power surge or a motor that won’t hold position, we carry parts for the common failures and can usually have things running the same visit. For older units, we’ll tell you when a retrofit makes sense and when you’re throwing money at an operator that’s already obsolete. The honest answer is always cheaper than the third service call.
Related: Gate Parts & Welding across our full service area.
Common Gate Parts & Welding Problems We See in El Reno Homes
- Expansive clay heaving hinge posts. The same soil that cracks foundations in Canadian County also shoves gate posts out of plumb. A gate that dragged last summer may not latch this spring. We reset the post, often deeper than before, with drainage gravel.
- Storm-bent steel pipe rails. El Reno sits in one of the most tornado-active corridors in the country. When wind throws debris into a cattle gate, the rail bends or snaps, and the livestock security clock is running. Our welder is on the truck.
- Legacy gate operators missing entrapment protection. Openers installed before UL 325 became standard often lack working safety edges or photo eyes. A power surge from tornado-season electrical disruptions can kill an obsolete board, and then the gate either won’t close or closes on anything in the way.
- Worn rollers and latch mismatch on sliding gates. Wind-driven dust and Oklahoma clay grit eat roller bearings. We replace rollers, realign tracks, and adjust latches so the gate doesn’t rattle itself loose every time the wind picks up.
Pricing for Gate Parts & Welding in El Reno, OK
A typical hinge replacement in El Reno runs $120 to $260, depending on the size and weight of the gate. Post replacement usually lands between $180 and $400, with the higher end for heavy steel-pipe posts set in concrete for cattle gates. Custom welding on a bent rail or cracked frame is generally $90 to $250 per repair, again depending on how much steel needs cutting and replacing. The price is quoted and agreed before any work starts. No trip charge inside Canadian County. We also take $40 off any repair over $200, and seniors and veterans get a permanent 10% discount. Call (877) 610-2993 and we’ll give you a number over the phone based on what you’re describing.
We Also Serve Cities Near El Reno
Beyond El Reno, we handle gate parts and welding work in Yukon, Piedmont, Mustang, and Bethany. If you’re in one of those towns, the same crew, the same El Reno area coverage, and the same 90-Day Done Right Promise apply. One call covers all of it.
Serving El Reno, OK - Our Local Coverage Area
We’re based in the El Reno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in El Reno
Most bent pipe gates can be straightened and reinforced, especially if the bend is in the rail rather than the post. We cut out the worst of the bend, weld in a replacement section, and add a brace where the original design flexed. If the gate has bent in multiple places or the frame has fatigued, replacement is often cheaper than back-to-back repairs. We’ll show you the welds and tell you straight. Call (877) 610-2993 for an exact quote.
After a storm in El Reno, the usual culprits are a fried control board from a power surge, a limit switch knocked out of adjustment, or a bent gate frame that’s binding the operator. We troubleshoot in order: power, board, limits, then the gate itself. If the board is dead on an older LiftMaster, we’ll price a retrofit against a new operator and give you both numbers. Estimates are free.
Yes. Our trucks carry welders, schedule 40 pipe, hinge stock, and the hardware to reset a snapped post. When a storm rolls through El Reno and someone’s cattle are standing at an open gate, we treat it as an emergency. Call (877) 610-2993 and a live person answers, day or night.
Because the post is moving, not the bolts. El Reno’s expansive clay soil heaves and shifts seasonally, and a hinge post set shallow will lean a little more every year. Tightening hinges on a leaning post is like straightening a picture on a sinking wall. The fix is resetting the post deeper with drainage gravel and concrete, then rehanging the gate with heavier hardware. We do that work in El Reno regularly. Call for a free estimate.
In many cases, yes. We can add photo eyes, safety edges, and updated control boards to older operators, provided the motor and gearbox are still sound. If the operator is so old that parts aren’t available, we’ll say so and price a replacement. A gate that closes on a child or a dog is not a gamble worth taking. Call (877) 610-2993 and we’ll walk through what you have.
If your gate is sagging, bent, or the operator won’t run after the last storm, call (877) 610-2993 for a free estimate. Hal Gatewood has been fixing gates since 2001, and the 90-Day Done Right Promise is in writing on every job. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving El Reno and Canadian County since 2001.