Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across East Aurora
Gate parts and welding in East Aurora usually means one of three things: a hinge that has torn loose from a stone post, a sagging gate that drags across the walkway, or an old operator that has finally quit. A typical hinge replacement on a period iron gate in the village runs $180 to $420, while custom welding work on a broken ornamental hinge starts around $150 and goes up from there based on what has to be fabricated and fitted. We are Gatewood Fence & Gate, and we have been fixing gates since 2001. Hal Gatewood’s name is on the shop, his address is published, and the person who answers when you call (877) 610-2993 is someone who will actually show up in the window we promised.
Why Gatewood Fence & Gate Is East Aurora’s Preferred Gate Parts & Welding Company
Folks around East Aurora do not want to gamble on gate repair. Too many homeowners here have already been burned by an outfit that quoted one price on the phone and charged another at the door. We do not work that way. The price is quoted and agreed before any work starts, and every job carries our 90-Day Done Right Promise in writing. If it is not done right, we make it right. One call brings Hal back, no runaround.
We carry a strong local reputation in East Aurora because we fix what other companies want to replace. On Oakwood Avenue in the historic village, our crew worked on a heavy wood swing gate hung on a cracked brick pillar. The original cast-iron hinge post had shifted out of plumb after a hard winter, dragging the gate across the stone walk. We removed the old post, poured a new concrete footing with rebar doweled into the existing footer, and re-welded the pivot hinge to a custom steel bracket set into the brick with two-part epoxy. We also re-aligned the latch and strike plate so the gate closes without lifting. The gate now clears by an inch and swings square through multiple freeze-thaw cycles.
That is the difference between a parts-swapper and someone who welds on site in your driveway. We show up in a background-checked, uniformed truck. We do not haul your gate off to some shop across the county. The work happens where you can watch it happen.
Our Gate Parts & Welding Services in East Aurora
Our Gate Parts & Welding team handles hinge replacement, post replacement, rail repair, and custom welding on gates of every age, from 1890s Victorian ironwork to 1990s tubular steel. In East Aurora specifically, we spend a lot of time working around original stone and brick pillars that cannot accept modern bolt-on hardware without cracking. That changes how we approach the job.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. In East Aurora, original ornamental iron hinges are often welded or mortared directly into stone or brick posts. You cannot just bolt a universal hinge from the hardware store onto that post, not without splitting the masonry. We cut the old hinge free, clean the seat, and weld or epoxy a proper steel plate into the existing stone so the new hinge carries the gate the way the original did. Typical hinge replacement on a period iron gate in East Aurora runs $180 to $420 depending on how much fabrication the post requires.
Post Replacement
Stone and brick gate pillars in East Aurora heave and crack every spring. When a post has shifted far enough that the gate drags, we pull the old post, pour a new concrete footing with rebar doweled into the existing footer, and set a new steel or wood post plumb. In the Roycroft district, original iron gate hinges are often mortared directly into stone gate posts, so when our techs replace a hinge post we must core and epoxy an inset mounting plate. A standard bolt-on bracket from a big-box store would crack the masonry within one freeze-thaw season. Post replacement in East Aurora typically runs $450 to $1,200 per post, depending on footing depth and whether the pillar is stone, brick, or wood.
Rail Repair
A bent or rusted-through rail is a structural problem, not a cosmetic one. On older East Aurora gates, the bottom rail usually fails first because it sits closest to snow and road salt. We straighten what can be straightened, cut out and weld in new steel where it cannot, and re-pin the pickets so the gate does not rack. Rail repair runs $120 to $380 per rail, including welding on site and rust treatment before we prime.
Custom Welding
This is where an old gate gets a second life. Broken scrollwork, a snapped hinge leaf, a cracked frame corner, a striker plate that has torn loose. We weld it on site, in your driveway, so you see exactly what was repaired and how. Custom welding work in East Aurora starts around $150 for a small crack or broken hinge and runs to $600 or more for a full gate rebuild with new bottom rail and hinge plates. If you have an ornamental gate you cannot replace because nothing at the lumberyard matches it, welding is usually the cheaper answer.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in East Aurora
We service nine major gate brands, including Viking, Ghost Controls, and DoorKing, and we keep common parts stocked for East Aurora customers so we are not waiting on a warehouse in another state. That matters with older operators, because a 1990s Viking or Ghost Controls board is not something you find at the parts counter anymore. We know which boards can be retrofitted and which ones have to be replaced outright, and we will tell you the truth either way before you spend a dollar. We are certified to service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Common Gate Parts & Welding Problems We See in East Aurora Homes
- Stone or brick hinge posts cracking and shifting from freeze-thaw. East Aurora sits at roughly 900 feet elevation on the Allegheny Plateau escarpment, deeper in the lake-effect snowbelt than lower-elevation western NY suburbs. Annual snowfall regularly exceeds 100 inches, and the freeze-thaw cycling pushes posts out of plumb by an inch or more each spring.
- Original ornamental iron hinges welded or mortared into masonry. These cannot be replaced with universal bolt-on hinges without cracking the post. We core, epoxy, and weld a proper inset plate instead, which is the only repair that survives another East Aurora winter.
- Obsolete control boards on older gate operators. Many FAAC, Linear, and Viking operators from the 1990s have control boards that cannot be upgraded with modern UL 325 entrapment protection. In those cases, repairing the board is a dead end, and replacing the operator is the honest answer.
- Wood gates warping and dragging after wet winters. Heavy snow load and repeated freeze-thaw cycles warp wood gates year over year. Fix the panel without the post and you will fix it twice. We always check the post first.
Pricing for Gate Parts & Welding in East Aurora, NY
What you pay depends mostly on how much fabrication the job needs. A straightforward hinge replacement on a wood gate runs $150 to $300. A period iron hinge on a stone post runs $180 to $420 because we are coring, epoxying, and welding an inset plate, not driving screws. Post replacement runs $450 to $1,200 per post. Custom welding starts around $150 and runs to $600 or more for a full rebuild. Rail repair runs $120 to $380 per rail. Every job is quoted and agreed before we start, so the number on the invoice is the number you approved. Call (877) 610-2993 for an exact quote and we will come out and look at the gate, no trip charge inside Erie County, and a free second opinion on any written estimate you already have.
We Also Serve Cities Near East Aurora
Our Gate Parts & Welding in East Aurora coverage extends to Lancaster, Depew, Cheektowaga, and Lackawanna when your gate is outside the village proper. Same owner-operated crew, same 90-Day Done Right Promise, same phone number. If you are a few miles down the road, we will still come look at the gate for free.
Serving East Aurora, NY - Our Local Coverage Area
We’re based in the East Aurora area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in East Aurora
Yes. In most cases we can repair a cracked stone hinge post without rebuilding the pillar. We remove the hinge, clean the crack, epoxy steel pins into the masonry, and weld a custom steel plate to carry the hinge load. The gate stays in your driveway, the stone stays in the ground, and the repair survives freeze-thaw because the plate is set with two-part epoxy, not wedged into a crumbling mortar joint. Post repair typically runs $300 to $800, which is usually cheaper than a full pillar rebuild. Call (877) 610-2993 and we will tell you which one your gate needs, honestly, with a written quote before any work starts.
Because the post moved, not the gate. East Aurora’s freeze-thaw season heaves gate posts out of plumb, especially posts set without a deep concrete footing. Adjusting the hinges takes the sag out of the gate itself, but if the post has shifted an inch, the gate will drag no matter how tight the hinges are. We reset the post with a new footing, rehang the gate square, and the drag goes away for years, not months. Post reset and rehang in East Aurora runs $450 to $1,200 depending on the post. Call us at (877) 610-2993 and we will put a level on the post before we touch the hinges.
Usually not, and we will tell you that before you pay for anything. A 1990s LiftMaster swing operator has a control board that cannot accept modern UL 325 entrapment protection, which means repairing the board leaves you with an operator that does not meet current safety standards. In that case, replacing the operator is the honest answer, and we will quote the full replacement, including the safety edges and photocells, before we order a single part. We service current LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule models. Call (877) 610-2993 for a written replacement quote.
No. A broken hinge welded to an original post is one of the most common repairs we do in the Roycroft district, and replacing the gate is almost never the right first step. We cut the old hinge off the post, grind the weld clean, fabricate a matching hinge in steel, and weld it back into place. If the post itself has cracked, we core and epoxy an inset mounting plate before re-welding, because a bolt-on bracket would crack the masonry within one freeze-thaw season. This repair usually runs $250 to $600 per hinge. Call (877) 610-2993 and we will look at the gate before anyone tells you to replace it.
Sometimes. If the existing operator has a control board that can accept a modern receiver and safety inputs, we can add a keypad and photocells without replacing the operator. If the board is obsolete, we will tell you that the operator itself has to be upgraded to meet current UL 325 entrapment protection standards before we add entry devices. We also have to mount the photocells so they survive a stone post, which in East Aurora means epoxy-set brackets, not concrete screws that crack the stone in February. Keypad and photocell retrofits run $350 to $900, plus the operator replacement if that is what the old board requires. Call (877) 610-2993 for a written quote before you order anything online.
Call Gatewood Fence & Gate for Gate Parts & Welding in East Aurora
If your gate is dragging, sagging, welded to a cracked post, or running on a control board from the Clinton administration, we will come look at it and tell you the truth. Free estimate, written price before any work starts, and a 90-Day Done Right Promise on every job. Hal Gatewood has been fixing gates since 2001, and his name is on the shop, not a franchise agreement. Call (877) 610-2993, and a live person answers, day or night. No voicemail, no call center, no chatbot. Just a guy who will hand you his cell number and mean it.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.