Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Duvall
Gate parts and welding in Duvall, WA usually means one of two things: a broken hinge on a farm gate that won’t swing, or a rusted-out post that’s letting the whole thing sag into the gravel. Most jobs at Gatewood Fence & Gate run between $185 and $620 for the repair itself, and we weld on site so the gate stays in your driveway. If you’re off Woodinville-Duvall Road or up toward Cherry Valley, call (877) 610-2993 and a live person answers, day or night. Hal Gatewood has been fixing gates since 2001, and the name is on every invoice.
Why Gatewood Fence & Gate Is Duvall’s Preferred Gate Parts & Welding Company
We’ve lost count of the gates we’ve repaired in the 98019 zip code, but we remember the properties. The horse place on NE Cherry Valley Road where the Snoqualmie flood heaved the hinge post four inches. The rambler on Stewart Street with a slide gate that had crushed its own rollers. The newer acreage builds out by Lake Rasmussen where the developers put ornamental hardware on a gate built for pipe rail. Every job gets the same treatment: Hal or one of his crew shows up in a marked truck, looks you in the eye, and tells you what actually needs to be replaced and what can be welded and saved.
Duvall customers call us because we weld on site instead of hauling the gate to a shop. That matters when you’ve got a 14-foot farm gate that weighs 300 pounds and is currently keeping a horse in. Our Gate Parts & Welding team carries most hinge plates, latch hardware, and gate rollers in the truck, and anything we don’t have is ordered and on-site within two to three business days. The 90-Day Done Right Promise is stamped in writing on every job. One call brings us back, no runaround, no fine print.
There’s a standing offer too: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. We publish our address and license number. Hal’s name is on the shop. That’s the oldest accountability there is.
Our Gate Parts & Welding Services in Duvall
Hinge Replacement
In Duvall’s saturated valley soils, hinge posts heave after wet winters, throw the gate out of plumb, and the hinges take the strain until something snaps. We cut out the rotted footing, pour a deeper concrete base, and weld new hinge plates at the correct angle. For pipe-rail pasture gates and farm-style swing gates, we use weld-on barrel hinges or heavy-duty strap hinges rated for the gate’s actual weight, not whatever came in the box from the big-box store.
Post Replacement
A sagging gate is a post problem, not a panel problem. Fix the panel without the post and you’ll fix it twice. In Duvall we set replacement posts in deeper concrete footings than the original builder used, especially on low-lying parcels near the Snoqualmie River where frost and saturation work posts loose over a few seasons. We handle both wood and steel posts, and when the old post is rusted or rotted at the base, we cut it out and weld in a new steel post set below the mud line.
Rail Repair
Pipe-rail gates on horse properties take abuse from livestock leaning into them, and the horizontal rails are usually the first thing to crack at the weld. We weld new rail sections in place or reinforce the existing rails with gussets and cross-bracing. On lighter ornamental gates in newer Duvall developments, we do the same kind of repair on thin-gauge steel when the factory welds fail, which they do more than anyone wants to admit.
Custom Welding
Sometimes the gate was never right for the opening, or the original builder sized it wrong. We do custom welding to extend, narrow, or reinforce gates so they actually fit the driveway. That includes welding new mounting plates for gate rollers, fabricating latch extensions, and building up worn hinge barrels. If you’ve got a gate that’s close but not quite right, bring us a photo or we’ll come look.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Duvall
We’re certified to service nine major gate brands, and in Duvall we see a lot of Linear, Viking, and Ghost Controls openers on acreage gates and long driveways. We stock common parts for these systems locally and can get anything else fast. When a Viking operator on a farm swing gate fails, it’s usually the limit switch or the capacitor, and we can have it running same afternoon without waiting a week for a part from out of state. Same goes for ghost-controls solar openers on gates where running mains power to the entrance would cost more than the gate itself.
Common Gate Parts & Welding Problems We See in Duvall Homes
- Heaved hinge posts after wet winters. The Snoqualmie Valley’s moisture-saturated soils expand and contract, pushing posts out of alignment and cracking welds at the base. We see this most on older 1970s-1990s farm properties and on anything in the floodplain.
- Worn slide gate rollers on gravel driveways. Long gravel drives accumulate rock dust and grit that chews up roller bearings and rack-and-pinion teeth. Paved suburban gates in Woodinville don’t have this problem; almost every long driveway in Duvall does.
- Silted-out underground operator pits near the Snoqualmie River. Buried motor pits fill with silt and debris after high water, and the wiring conduits corrode. We recommend above-post or pedestal-mounted operators for any parcel that sits in the mapped floodplain.
- Cracked pipe-rail welds from livestock pressure. Horses and cattle lean into gates, and over time the rail welds crack at the hinge post. We re-weld and reinforce these so the gate doesn’t fold under a 1,200-pound animal testing it.
Pricing for Gate Parts & Welding in Duvall, WA
Here’s what we typically see in Duvall. Hinge replacement runs $185-$340 depending on the gate’s weight and whether the post needs resetting. Post replacement is $290-$520 for a standard steel or wood post with new concrete footing. Rail repair and custom welding run $150-$480 depending on how much fabrication is involved. A full gate rebuild, like the equestrian pipe-rail gate off NE Cherry Valley Road we did after the last flood cycle, usually falls between $600 and $1,200 including new hardware and operator remounting. The price is quoted and agreed before any work starts, and it doesn’t change at the door. Remember the standing offer: $40 off any repair over $200. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Duvall
We work Duvall, Cottage Lake, Union Hill-Novelty Hill, Woodinville, and Redmond regularly. If you’re on the edge of two service areas, check our Gate Parts & Welding in Duvall page or just call (877) 610-2993 and we’ll tell you straight if we cover your road.
Serving Duvall, WA - Our Local Coverage Area
We’re based in the Duvall area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Duvall
The hinge is rarely the real problem. The post is moving. In Duvall’s saturated valley soils, the hinge post heaves in wet seasons, and no amount of tightening or shimming fixes a post that’s lost its footing. The fix is resetting the post in a deeper concrete base, then re-welding the hinges level. Call (877) 610-2993 and we’ll tell you if your post can be saved or needs replacing.
No. If your property is in the mapped Snoqualmie River floodplain, a buried motor pit will silt out and fail, usually at the worst possible time. We recommend an above-post or pedestal-mounted operator instead, where the motor stays out of the water. Floodwater gets into the pit, clogs the actuator hardware, and corrodes the underground wiring conduit, and we see the same damage every high-water cycle.
We use MIG welding for most pipe-rail pasture gates because it gives clean, strong beads on the heavier-gauge steel that farm gates are built from. For thinner ornamental gates we switch to TIG to avoid burn-through. The goal is a weld that’s stronger than the surrounding metal, so the gate breaks somewhere else before the weld fails.
Yes, and we do it regularly around Duvall where running mains power to the gate entrance is impractical or would cost thousands. We size the operator for the gate’s actual weight and width, mount the solar panel, and install a pedestal or above-post motor so it stays out of floodwater. Call (877) 610-2993 for a free assessment.
Hinge posts heave and need resetting, gate frames warp and need straightening or re-welding, and underground actuator hardware gets silted out and corroded from the water. Wooden gate boards rot at the base, and steel components develop surface rust within a single wet season. If the river got to your gate, get it looked at before the next high-water cycle. Estimates are free.
Call Gatewood Fence & Gate for Gate Parts & Welding in Duvall
If your gate is sagging, your hinges are cracking, or your operator quit after the last flood, give us a call at (877) 610-2993. Hal Gatewood has been doing this since 2001. We weld on site, quote before we start, and put the 90-Day Done Right Promise in writing. Show me the gate closing on its own and I’ll show you where it’s failing. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Duvall since 2001.