Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Duluth
Most gate problems in Duluth aren’t the panel. They’re the hinge post, the bracket, the weld that finally let go after 25 years of Georgia red clay heaving underneath it. We fix that. Gatewood Fence & Gate has been owner-operated since 2001, and when you call (877) 610-2993, you get Hal or one of his crew, not a voicemail tree. We show up in Duluth with a welder in the truck and the parts to finish the job the same day.
If your gate drags on the approach, stalls mid-swing, or a hinge bracket has torn loose from the pillar, that’s our bread and butter. Our Gate Parts & Welding team cuts out the rot, welds fresh steel, and re-aims the gate so it closes true. You don’t haul the gate anywhere. We fix it in your driveway.
Why Gatewood Fence & Gate Is Duluth’s Preferred Gate Parts & Welding Company
Duluth isn’t like the rest of Gwinnett County. The gated subdivisions along Sugarloaf Parkway, Old Peachtree Road, and around Sugarloaf Country Club were built in a rush between 1990 and 2008, and the ornamental iron and aluminum swing gates installed then are now hitting the same failure window all at once. We’ve been through this cycle enough to know what’s failing before we even pull up. Red clay post heave, corroded hinge pins, operators that were never re-calibrated after the footing settled. Same story, different street.
Duluth homeowners and HOA boards call us because Hal’s name is on the shop and the shop is down the road, which is the oldest accountability there is. Every job comes with the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. No runaround.
We also answer the phone with a live person 24 hours a day. When a subdivision gate on Old Peachtree Road stalls open at 11 p.m., the person who picks up can actually dispatch someone who knows Duluth, not a call center three states away.
Scheduling from our Atlanta office, crews serve Duluth locally, so response times are measured in hours, not days. A live person answers every call, 24/7. Every technician is background-checked and uniformed.
Our Gate Parts & Welding Services in Duluth
Here’s what we actually do in Duluth, week in and week out. These are the four repairs we make most often in this area, and each one starts with a written price you approve before any work begins.
Hinge Replacement
Hinges are where Duluth gates die. The combination of humid air and red clay soil means a 20-year-old hinge pin can be rusted halfway through while the gate still looks fine from the street. We cut the old hinge off, weld a new one on at the corrected height, and re-hang the gate so it swings without dragging. Many Duluth swing gates were welded with undersized hinges to begin with, so we often go up a size when we replace.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. Duluth’s expansive red clay pushes post footings around seasonally. If your post has shifted, the only real fix is to dig it out, pour a deeper footing with a thicker wall sleeve, and set the post plumb. Then we weld the brackets back on. We’ve done this on stacked-stone pillars near Sugarloaf Country Club, on brick columns in 30096, and on plain steel posts in 30095.
Rail Repair
Rails crack where the weld meets the picket, especially on aluminum gates that flex every time the operator cycles. A cracked rail lets the gate rack out of square, which loads the hinge side and strips operator gears. We grind out the cracked weld and lay in a fresh one, then reinforce the rail so it doesn’t crack in the same place twice. Fix the rail without checking the post and you’ll fix it twice.
Custom Welding
Sometimes you need a bracket that doesn’t exist anymore, a gate that’s been hit by a car, or a pedestrian gate that never closed right from day one. We weld on site in Duluth, fabricating what’s needed rather than ordering a part that’s been discontinued for a decade. Custom fabrication means we match the existing gate style, whether it’s the wrought-iron double-swing at a Sugarloaf Country Club estate or a lighter aluminum single-swing in a mid-range 30097 subdivision.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Duluth
We stock and service parts for the gate operators you already have. Ghost Controls and DoorKing operators are common in Duluth’s newer subdivisions, while Viking and Elite systems show up on the heavier custom gates near Sugarloaf Country Club. We keep hinges, brackets, welders, and common drop-in parts on the truck, which means less waiting on a supplier and more finishing the job the day we start. If your HOA’s operator is older, we can usually match what’s there without replacing the whole system.
Common Gate Parts & Welding Problems We See in Duluth Homes
- Red clay post heave shifting hinge posts. Gwinnett County’s expansive clay swells when wet and contracts during dry spells, pushing post footings out of plumb over years. The gate starts dragging, the operator strains, and eventually strips its own gears. The fix is post re-set, not a new operator.
- Corroded hinge pins snapping after January ice. Duluth’s ice storms are rare but real. Water gets into a 20-year-old hinge pin, freezes, and the next time the operator cycles, the pin shears. An entire HOA entrance can be left inoperable until we get there. We weld fresh hinge assemblies that shed water instead of trapping it.
- Loop detectors that stopped reading cars after settling. When a gate’s post shifts even an inch, the loop detector in the driveway may no longer see a car pulling up. The operator times out, the gate stalls, and residents think the motor is dead. Often the fix is re-aiming and re-calibrating, not replacing the operator.
- Welded brackets tearing out of brick or stone pillars. The original weld was fine, but the masonry was never meant to take a swinging gate’s load for 25 years. We weld a proper bearing plate, bolt it through the pillar, and re-hang the gate so the load goes where it should.
Pricing for Gate Parts & Welding in Duluth, GA
Hinge replacement in Duluth typically runs $180-$320 per hinge, depending on gate weight and whether we’re welding or bolting. Post replacement with a new footing usually lands between $450 and $900, more when we’re working around stacked-stone pillars. Rail repair and re-welding a cracked joint runs $150-$400. Custom welding jobs are quoted at an hourly rate, usually $95-$135 per hour plus materials. You get a written price before any work starts, and that price doesn’t change at the door.
We don’t charge a trip fee inside Gwinnett County, so calling us out to Duluth to look at your gate costs you nothing. Seniors and veterans get a permanent 10% discount. Any repair over $200 gets $40 off. If another company gave you a written estimate, bring it and we’ll give you a free second opinion. Call (877) 610-2993.
We Also Serve Cities Near Duluth
Most of our Duluth customers find us through their HOA, but we get plenty of calls from neighboring communities too. We serve Gate Parts & Welding in Duluth and regularly run routes through Norcross, Lawrenceville, Suwanee, and Peachtree Corners. Same crew, same 90-Day Done Right Promise, same live person on the phone.
Serving Duluth, GA - Our Local Coverage Area
We’re based in the Duluth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Duluth
Red clay expands and contracts with moisture, which slowly pushes gate post footings out of plumb over the course of years. When the post shifts, the gate drags, the hinges bind, and the welds at the hinge brackets start to crack. In Duluth’s 1990-2008 gated subdivisions, this is the single most common reason a gate stops closing properly. Re-setting the post and re-welding the hinges is the real fix. Call (877) 610-2993 and we’ll tell you if that’s what your gate needs.
Yes, in almost every Duluth HOA, changes to gate style, height, finish, or hardware require architectural review first. We’ve worked with enough Duluth management companies to know the drill, and we’re happy to provide whatever documentation your board needs before any work starts. We won’t ask you to skip approval. Getting it done right the first time includes not fighting the HOA afterward.
Ice builds up on wide ornamental swing gates, doubling their weight overnight. Older LiftMaster and Linear operators can’t handle the load, and the gate either stalls or torques a hinge bracket loose. Welding alone won’t prevent ice, but a properly welded and reinforced hinge assembly, plus re-aiming the operator’s sensitivity, keeps the damage from becoming a full gate failure. If your HOA gate stalls after freezing rain, call (877) 610-2993.
UL 325 compliance means the operator has to sense an obstruction and reverse, and welding can change a gate’s weight enough to affect that. After we weld or reinforce a gate, we re-test the operator’s force settings and safety edges. If your entrapment protection is outdated, we’ll tell you, and we’ll price the fix in writing before starting.
On those heavy wrought-iron double-swing gates, the most common failure is the weld at the hinge bracket where it meets the pillar plate. Years of operating torque cracks that weld, then the gate starts to sag and the pillar plate works loose from the stone. We cut the old bracket off, weld on a heavier one, bolt through the pillar, and re-hang the gate. The job usually takes a day. Estimates are free at (877) 610-2993.
Call Gatewood Fence & Gate for Gate Parts & Welding in Duluth
If your gate is dragging, sagging, or a weld has let go, call (877) 610-2993. You’ll talk to a person, not a phone tree. We’ll set a time, show up when we said we would, and hand you a written price before any work starts. Hal Gatewood has been running this shop since 2001, and his name goes on every invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Duluth since 2001.