Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Cudahy
Gate parts and welding in Cudahy usually come down to one thing: the post, not the hinge. On these small, dense lots, a sagging gate that scrapes the driveway almost always traces back to a leaning post sitting in clay soil that heaved years ago. At Gatewood Fence & Gate, Hal Gatewood and his crew fix that in your driveway with on-site welding, re-plumbing the post so the gate swings true again. If your gate drags, binds, or won’t latch, call (877) 610-2993 and a real person picks up, any hour.
We work all over Cudahy’s 90202, from the duplex courts off Atlantic Ave to the converted single-families near Clara Street Park and the tight apartment rows around River Road. When every foot of driveway counts, a repair has to be right the first time.
Why Gatewood Fence & Gate Is Cudahy’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001. His name is on the shop and on every invoice, and the crew showing up to your Cudahy property works for him, not a subcontractor. The difference shows when someone re-welds a rusted bottom rail instead of telling you to buy a whole new gate. That’s the repair-first habit this area needs, because so many of the 1940s-1960s iron gates here still have good bones, just failed posts and rusted rails.
Cudahy customers call us for two reasons: the gate fails, or another company already “fixed” it and it failed again. We see the sloppy work. Loose hinge bolts where the post is actually out of plumb. A welded rail that didn’t address the footing heave underneath. A gate that closes on its own is our definition of done right, and our 90-Day Done Right Promise is in writing on every job. One call brings us back, no argument.
We service Cudahy and Southeast LA local gates constantly, so a trip here isn’t a special dispatch. It’s our normal route. And our Gate Parts & Welding work always starts with the same question: what failed first, and what caused it.
Our Gate Parts & Welding Services in Cudahy
Post Replacement
This is the big one in Cudahy. Clay soil swells in winter and shrinks in summer, and the original 1960s post footings were poured shallow. The post leans, the gate drags, and no amount of hinge adjustment fixes it. We dig the old post, set a new one with a properly deep concrete footing, and weld it plumb. In Cudahy’s narrow driveways, we’re also careful about swing clearance, because getting the post 2 inches wrong means the gate won’t clear the slab or the fence line.
Hinge Replacement
Sometimes the hinge is genuinely worn. But on this soil, a hinge that binds or shears is usually the symptom. We check the post first, then replace hinges with steel or stainless that will outlast the original iron. On a tight duplex off Atlantic Ave, the hinge post had leaned 1.5 inches toward the driveway, so we re-plumbed the post, re-welded the base, replaced the worn gate rollers, and re-hung the latch. The gate never dragged again.
Rail Repair
Rusted-through bottom rails near the hinge post are a Cudahy classic. Years of smog-basin moisture and poor paint mean the bottom rail fails before anything else. We cut out the rotted section and weld in a new rail on site, then prime and rust-coat the repair. If the rest of the gate is solid, a new rail gets years back. If the whole frame is compromised, we tell you straight, without inventing a reason to sell a new gate.
Custom Welding
Some of Cudahy’s older ornamental gates need a patch that no shelf part fits. We cut, bend, and weld on site, matching the existing rail profile so the repair doesn’t look like a repair. Gate rollers, latch plates, and operator brackets also get welded on rather than bolted whenever possible, because bolts work loose faster on a gate that sees daily use on a rental driveway.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Cudahy
Hal is certified on DoorKing, Elite, Viking, and most other major operator brands you’ll find on Cudahy swing and slide gates. We keep common parts for older DoorKing and LiftMaster units in the truck, so a corroded loop detector or a seized gear doesn’t mean waiting a week. If a rental property’s operator has never been serviced and the gate is now manual, the problem is usually a detector or a limit switch, and we find it faster because we’ve seen this same failure across Cudahy for over 20 years.
Common Gate Parts & Welding Problems We See in Cudahy Homes
- Post heave and lean. Clay soil under Cudahy’s shallow 1960s footings swells and shifts seasonally, nudging posts out of plumb until the gate drags on the concrete apron. This is why we re-plumb posts instead of just tightening hinges.
- Rusted-through bottom rails. Smog-basin air and UV-exposed paint means the bottom rail near the hinge post corrodes first. We cut and weld a new rail, and often see the top rail still solid, which is why a full gate replacement is rarely necessary.
- Failed loop detectors on rental duplexes. Dense multi-unit properties use automatic operators hard, and when the loop at the driveway apron stops sensing a car, tenants swing the gate manually, which wears the hinges unevenly.
- Latch and lock misalignment from shifted posts. A post that moved a quarter-inch means the latch doesn’t catch, so the gate bangs in the wind or sits open. Re-plumbing the post fixes the latch, not the reverse.
Pricing for Gate Parts & Welding in Cudahy, CA
A typical hinge replacement on a Cudahy swing gate runs $180-$320, depending on how much re-welding the hinge mount needs. Post replacement runs $450-$900 when we dig, set, and weld a new post with a deeper footing. Bottom rail repair, including cutting out rust and welding in new stock, usually falls between $220 and $480. Full custom welding jobs run higher because they’re built to the gate, not from a catalog. Every job’s price is quoted and agreed in writing before any work starts. No trip charge inside Los Angeles County, and we stand behind every weld and every part with the 90-Day Done Right Promise. Call (877) 610-2993 for a free estimate, and mention the $40-off-any-repair-over-$200 offer when you call.
We Also Serve Cities Near Cudahy
Our Gate Parts & Welding in Cudahy service also covers Maywood, Huntington Park, Walnut Park, and Commerce. If you’re just down the street in any of those towns, the same crew and the same on-site welding applies. Call us and we’ll have a real person on the line, not a phone tree.
Serving Cudahy, CA - Our Local Coverage Area
We’re based in the Cudahy area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Cudahy
Because Cudahy sits on clay-heavy soil that swells when wet and shrinks when dry, and most original 1960s post footings are only 18 to 24 inches deep. That’s too shallow for this soil, so posts heave and lean every season. The fix is digging out the old footing and pouring a deeper one, which we do on site. Call (877) 610-2993 if your post is out of plumb, and we’ll give you a straight answer about whether it’s a re-plumb or a full replacement.
If the rest of the gate frame is solid, we weld a new bottom rail in place, usually for $220-$480. Rust here starts at the bottom rail near the hinge post, so the top rail and diagonal work often survive fine. Replacing the whole gate is only needed when the frame is compromised or the rust has reached the hinge plates. Call (877) 610-2993 and we’ll tell you honestly which one you actually need.
On Cudahy’s clay soil, nine times out of ten it’s the post. The hinge post leaned and took the gate with it. We confirm by checking the post for plumb before touching the hinge, then fix the actual cause so you’re not paying for a hinge adjustment every six months. Estimates are free.
We keep common DoorKing and LiftMaster boards, limit switches, loop detectors, and drive gears in the truck, so older slide gates in Cudahy’s dense rental areas get repaired same-visit most of the time. Hal is factory-certified on DoorKing, Elite, and Viking, so if the issue is a control board or a loop detector, we can diagnose it in the driveway. Call (877) 610-2993 and describe what the gate is doing, and we’ll bring the right parts.
We pour a deeper concrete footing, below the active clay zone, and set the post with gravel drainage at the base. That’s the detail the original 1960s installs missed. It costs a little more but it’s the only honest fix for this soil. Call (877) 610-2993 and we’ll walk you through what a proper footing in Cudahy actually requires, and quote it before any work begins.
Call Us for Gate Parts & Welding in Cudahy
If your gate drags, binds, won’t latch, or has rust eating through the bottom rail, call Hal Gatewood at (877) 610-2993. A live person answers, day or night. We’ll quote the job before any work starts, and the 90-Day Done Right Promise is in writing, not fine print. You can drive to the shop and look Hal in the eye, or he’ll come to your Cudahy driveway. Either way, the name is on the work.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Cudahy and Southeast LA since 2001.