Gate Repair in Citrus - Same-Day Repair, Priced Before We Start

Gate Repair in Citrus, CA

Gate repair in Citrus usually comes down to two things: a gate that was hung on a sloped driveway fifty years ago, and hinges that have been taking the punishment ever since. We fix gates the way they should have been built in the first place, with on-site welding and post work done in your driveway, not hauled off to a shop. If your gate is dragging, sagging, or refusing to open, call (877) 610-2993 and a live person answers, day or night.

Call (877) 610-2993

Why Citrus Homes Are Different

Citrus is unincorporated LA County, built out mostly in the 1950s through the 1970s on what used to be working citrus grove land. That left the community with ranch-style homes on generous lots, long sloped driveways, and original wrought iron swing gates that have rarely been touched since the day they were installed. Most of those gates went in on thin concrete pads without rebar or anchor bolts, and fifty years of summer heat expanding the steel has loosened them slowly. Then there’s the wind. Citrus sits at the base of the San Gabriel foothills, right where Santa Ana gusts funnel through the canyon mouths and hit older gates face-on. We see bent top rails, sheared hinge bolts, and slide gates knocked clean off their tracks after a good wind event. The properties along Barranca Avenue and the larger lots between Foothill Boulevard and the 210 are some of the most wind-exposed in the eastern San Gabriel Valley, and their gate hardware shows it.

Gate Repair in Citrus

Gate repair in Citrus starts with diagnosing why the gate failed, not just swapping the broken part. A sagging gate here almost always traces back to the hinge post, and a dragging gate traces back to the slope it was hung on. Hal and his crew have been fixing gates on these foothill parcels long enough to know that if you fix the panel without fixing the post, you’ll be fixing it again in two years.

Hinge & Post Repair

This is the most common repair call we get in Citrus. Hinge posts were originally set in footings that were never deep enough for the gate weight they carried. Add a sloped driveway where the gate binds on the uphill stroke, and the bottom hinge takes a beating on every single cycle. We dig out the old thin pad, pour a new post footing with anchor bolts, and remount the gate so it swings free. A hinge post rebuild with a new poured footing typically runs $600 to $1,200 depending on the post size and how much concrete has to come out.

Gate Realignment

A gate that sags in the middle usually means the post is leaning, not the panel. Realignment in Citrus almost always involves correcting the post first, then re-hanging the gate, then setting the hinges so the arc clears the driveway on both sides. On sloped lots, we re-cut the bottom rail angle or shim the hinge leaves so the gate travels clean instead of gouging the concrete. Gate realignment on a sagging double swing gate runs about $250 to $450 per leaf.

Weld & Rust Repair

Old wrought iron gates in Citrus rust where the pickets meet the bottom rail, and Santa Ana winds don’t do the compromised metal any favors. We cut out the damaged section, weld in new material, and grind it smooth so it looks original. Weld and rust repair on a typical bottom rail or hinge leaf runs $150 to $400.

For more on how we approach these repairs, see our full Gate Repair page.

Why do swing gates in Citrus drag on the uphill side of sloped driveways?

Because the gate was never installed on a level pad in the first place. Most Citrus swing gates from the 1960s through the 1980s were hung on driveways that pitch up toward the house. The gate’s arc intersects the grade on the uphill side, so the bottom rail scrapes concrete on every pass. Fixing it means rebuilding the post footing and re-hanging the gate on a corrected plane, not just adjusting the hinges. Call (877) 610-2993 for a free estimate.

Can a sagging gate in Citrus be fixed without replacing the whole gate?

In most cases, yes. Our repair-first approach means the gate stays in your driveway. We weld on site, rebuild post footings, re-hang the leaves, and re-align the arc so the gate runs clean. The only reason to replace a gate is if the frame is rusted through beyond structural repair or you’re changing the style and weight class entirely. We’ll show you the damage and explain what’s actually needed before any work starts.

Gate Installation in Citrus

Gate installation in Citrus usually means one of two things: a new custom gate on a sloped ranch lot, or replacing a 1960s-era wrought iron gate that’s been sagging for a decade. Most jobs run between $2,800 and $9,500 depending on the gate type, automation, and how much grade correction the driveway needs. We measure the actual grade before recommending anything, because a swing gate that drags uphill is a design problem, not a wear problem.

Swing Gate Installation

Swing gates dominate Citrus because the original homes were built with dual-leaf wrought iron at the street. The problem is those gates were installed on thin concrete pads, and the uphill leaf has been dragging for decades. When we build a new swing gate here, we set a reinforced hinge post footing above grade and size the leaves so the arc clears the concrete. A basic single-leaf swing gate with manual operation typically runs $2,800 to $4,500.

Sliding Gate Installation

Some Citrus lots simply should not have a swing gate. When the driveway slope makes a swinging leaf impossible without gouging the uphill side, a slide gate on a properly aligned track is the right call. We see slide gates in Citrus slip off their tracks because previous installers never accounted for the grade differential. Slide gate installations run $6,000 to $11,000 when the track needs realignment and a new operator.

Pedestrian Gate Installation

Not every entrance in Citrus needs to carry a vehicle. Pedestrian gates alongside driveway gates or at side yard entries are common on these ranch lots. We match the style to the main gate, set the posts in concrete, and hang the leaf so it swings true. If you’re adding an intercom or keypad, we’ll run the low-voltage wiring at the time of install so you’re not digging twice.

For more on what a full installation involves, see our Gate Installation page.

Why does my Citrus swing gate drag on the uphill side, and can a new installation fix that permanently?

The drag happens because the gate arc intersects the driveway grade, a direct result of original installs on 1960s and 70s ranch lots that were never regraded. A new installation fixes it permanently by setting the hinge post on a reinforced footing above grade and sizing the leaves to clear the concrete, or by converting to a slide gate. Call (877) 610-2993 and we’ll look at your specific grade.

How do I know if my Citrus property needs a slide gate instead of a swing gate?

If a swinging leaf would drag across the uphill concrete, bind at the hinge, or block more than half the driveway at full open, you need a slide gate. We measure the actual grade and arc before recommending one over the other. Many Citrus driveways that climb toward the house are better served by a slide gate with a properly aligned track and the right operator.

Gate Motor & Opener in Citrus

When a gate motor dies in Citrus, it’s rarely at a convenient time. You’re either stuck in the driveway or the gate is hanging half-open on a slope, and the Santa Ana winds are already working on the hinges. Gate motor and opener work here means matching an operator to a gate that was never designed for one, usually a heavy wrought iron swing gate from the 1960s or 70s on a sloped lot. We size the motor to the actual gate weight, the grade, and the wind load that funnels down from the canyons.

Motor Installation

Many of the ranch-style homes on the old grove parcels have gates that were retrofitted with operators years ago, and the original sizing was usually a guess. We install operators rated for the real load, not the brochure number. A typical swing gate motor installation in Citrus runs $900 to $1,800 depending on the gate weight and the condition of the existing mounting.

Motor Repair

Most motor repair calls in Citrus are things we can fix the same day: dead capacitor, burned control board, stripped limit switch, a gearbox full of foothill dust. If the motor still has life in it, we repair it. We don’t push replacements on people who don’t need them. A control board replacement in Citrus typically runs $190 to $380 installed, and a full swing gate motor swap usually runs $550 to $950.

Slide Motor

Slide motors are the workhorses for Citrus properties with long fence lines and narrow driveway frontages, especially along the busier sections off Citrus Avenue. We see a lot of chain-driven slide operators that have been neglected for decades, and the usual failure points are the nylon travel nut, the chain guide, and the limit switch. Repair work on a slide motor in Citrus usually falls between $250 and $650 for parts and labor.

For more on what we service and repair, see our Gate Motor & Opener page.

How fast can you get to my house in Citrus for a motor repair?

For motor repairs, we usually get a truck to Citrus the same day you call. Most service calls in the 91702 area are handled within a few hours during normal business, and we run 24/7 emergency service because an open gate off a main road at night is a real safety problem. Call (877) 610-2993 and a live person will tell you exactly when to expect us.

Is there an extra charge for emergency gate service in Citrus?

No trip charge inside the county, even for after-hours calls. The repair itself is quoted before any work starts, and our emergency pricing is the same as daytime pricing. The only thing that changes is our arrival time. We still answer the phone live at 3 a.m. because that’s when a gate motor usually decides to fail during a wind storm.

Gate Access Control in Citrus

When a keypad stops accepting the code you’ve used for years, or a phone entry system goes silent right before a delivery you scheduled, it derails the whole day. In Citrus, access control problems tend to show up differently than they do in flatter neighboring cities. The long driveways off Barranca Avenue, the older swing gates, and the hillside properties tucked below the foothills all put specific stress on wiring runs, keypads, and receivers.

Keypad & Intercom Repair

Dead keypads and silent intercoms in Citrus often trace back to corroded wiring connections in old junction boxes, or a receiver that’s been baked by years of foothill sun. We troubleshoot the full circuit, not just the device. Keypad replacement or intercom repair in Citrus typically runs $180 to $340 depending on the system and the wiring condition.

Phone Entry Systems

Weak cell signal at the gate is a common issue in Citrus, especially on sloped or low-lying parcels. We install higher-gain antennas, switch systems to dual-band modules, or relocate the unit to a spot with clean reception. A phone entry repair or antenna upgrade typically runs $220 to $480.

Receiver & Remote Service

When remotes stop working intermittently, the receiver is usually the culprit. We test signal strength, replace receivers, and reprogram remotes on site. Receiver replacement and reprogramming for a single gate in Citrus runs $125 to $275.

For more on what we can integrate and repair, see our Gate Access Control page.

Can you fix a phone entry system if my cell signal is weak at the gate in Citrus?

Yes, we do that regularly in Citrus. Weak signal on sloped or low-lying parcels is a common issue here. We install higher-gain antennas, switch systems to dual-band modules, or relocate the unit to a spot with clean reception. Call (877) 610-2993 and we’ll check your signal first.

How do your access control prices in Citrus compare to nearby cities?

Our Citrus pricing is consistent with Azusa, Vincent, Covina, and Glendora. What changes is the nature of the work, not the hourly rate. Citrus homes often require longer wire pulls and grade-specific mounting because of the sloped lots, so a job can cost a bit more in labor while parts remain the same price.

Gate Parts & Welding in Citrus

Gate parts and welding in Citrus typically runs $140 to $680 depending on whether we’re replacing a hinge, rebuilding a post, or cutting and welding a sagging rail back into square. We answer the phone around the clock, and we can usually have Hal or one of his crew at your driveway fast when a gate has dropped and won’t close. That matters here because Citrus sits right at the base of the foothills, where a Santa Ana wind event can leave a gate hanging by one hinge.

Hinge Replacement

Most original swing gates in Citrus were hung on barrel hinges welded straight to a square post. Fifty years of opening and closing on a sloped driveway has wallered out the hinge barrels until the gate drags on the uphill side. We cut the old hinges off, weld on new heavy-barrel ones, and shim the gate so it clears the grade. Hinge replacement on a single swing gate typically runs $180 to $340 including labor and materials.

Post Replacement

Citrus sits on what used to be working grove land, and the soil drains fast and shifts with the seasons. Gate posts set in the original thin pads from the 60s and 70s lean and crack. We cut the post at grade, core out the old concrete, set a new steel post deeper, and weld the gate back on. A full post replacement runs $420 to $680.

Custom Welding

Not everything that needs welding is a gate. We weld gate extensions for wide driveways, custom latch plates, steel reinforcement for sagging frames, and brackets for automation retrofits. Citrus has a lot of long, sloped driveways that were never designed for an operator, and the geometry often means an off-the-shelf opener won’t work without a custom arm. Custom welding is quoted at $95 to $140 per hour, with most small fabrication jobs falling in the $250 to $500 range.

For more on what we can fabricate and repair, see our Gate Parts & Welding page.

Is on-site welding safe for older gate frames and wrought iron in Citrus?

Yes, for most original steel and wrought iron it’s not only safe but the most durable repair option. We prep the area, shield surrounding materials, and weld in a controlled manner that preserves the gate’s appearance. If the steel is too thin or rusted through in multiple places, we’ll tell you before we weld, and we’ll explain what replacement would cost.

Does the 90-Day Done Right Promise apply to welding work in Citrus?

Yes, and it’s in writing on every invoice. Every job we do in Citrus carries our 90-Day Done Right Promise. If something isn’t right within 90 days, call us and we’ll come back and make it right. No charge, no argument. That’s the whole point of having Hal’s name on the shop.

Brands We Service in Citrus

We service FAAC, BFT, Linear, and Viking openers and control boards in Citrus, among others. We keep common replacement parts stocked on the truck, which means most motor and control board repairs happen same-day rather than waiting on a parts order. See our brands page for the full list of what we work on.

Pricing for Gate Repair in Citrus, CA

Neighborhoods We Serve in Citrus

We cover every part of Citrus, 91702. These are the areas we visit most often:

• The ranch-style parcels along Barranca Avenue
• The larger lots between Foothill Boulevard and the 210
• Hillside streets near the San Gabriel foothills
• Neighborhood streets running south toward Covina
• The older grove-parcel lots along Citrus Avenue

Typical response time across Citrus runs fast, usually same-day for urgent repairs. Call (877) 610-2993 and we’ll tell you exactly when to expect us.

Service Area - Cities Near Citrus

Gatewood Fence & Gate serves Citrus, CA and the surrounding foothill communities, including Azusa, CA, Vincent, CA, Covina, CA, Glendora, CA, and Charter Oak, CA. If you’re near the boundary and aren’t sure whether we cover your street, call and ask.

FAQs About Gate Repair in Citrus