Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Cibolo
Gate parts and welding in Cibolo usually comes down to one of three jobs: a hinge post that’s drifted out of plumb, a bottom rail that’s dragging concrete, or a latch that won’t catch because the whole frame has twisted. Most Cibolo gates are under 15 years old, and the failure isn’t age. It’s the clay. We fix the post, weld the rail, and realign the opener on site, in your driveway, without hauling the gate to a shop. Call Hal at (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Cibolo’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and his name is on the shop. The person who shows up in Cibolo is the person you’ll see again at the hardware store off FM 78, not a rotating crew from three counties away. We get called into Cibolo after national outfits quote a full gate replacement because a hinge post shifted. Most of the time, the gate itself is fine. We weld it, reset it, and it’s working again for a fraction of what a swap would cost.
Cibolo homeowners deal with something most gate companies don’t understand: Blackland Prairie clay. When it rains, the ground swells under your gate post. When it dries, it shrinks and leaves a void. That cycle throws posts 2 to 4 inches out of plumb inside a few seasons. A gate that looks straight can still bind at the latch because the frame is quietly twisting. We look at the post base first, and that’s usually where the answer is.
Our Gate Parts & Welding team stocks HOA-grade ornamental steel profiles and heavy-duty hinges on the truck, so most Cibolo jobs are done in one visit. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back. No runaround, no fine print.
Our Gate Parts & Welding Services in Cibolo
Hinge Replacement
HOA communities in Cibolo often mandate specific hinge styles to match the original architectural spec. If your subdivision’s design guidelines call for a barrel hinge or a heavy strap hinge in a particular finish, we weld what the committee approved, not whatever the parts store had on the shelf. A misaligned hinge isn’t just noisy; it transfers stress down the post and accelerates the clay-heave damage every Cibolo gate eventually deals with.
Post Replacement
This is the big one in Cibolo. Blackland Prairie clay heaves and settles, and a post set in a shallow footing will tilt like a fence post in wet weather. We cut the old footing, dig deeper, pour a concrete pier with rebar, and set the post plumb before anything else moves. If your gate is sagging at the latch side, the post is usually the culprit, even when the gate itself looks brand new.
Rail Repair
Bottom rails on swing gates catch the worst of it. They drag concrete, collect water at the weld points, and rust from the inside out where the factory coating was thinnest. We cut out the bad section and weld in new rectangular steel tubing, then grind and finish it to match the existing frame. In a Cibolo HOA, the finish has to match. We know that, and we match it before anyone files a complaint.
Custom Welding
Sometimes the part doesn’t exist. HOA-approved gates with non-standard post spacings, decorative scrollwork, or a rack and pinion mount that doesn’t match any catalog part need a torch and a steady hand. We weld custom brackets, shim plates, rack mounts, and hinges in the driveway. The gate stays in place while we work, so there’s no flatbed, no shop time, and no week-long gap in your fence line.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Cibolo
Most Cibolo driveway gates are automated, and a lot of them run on Viking, DoorKing, or Elite operators. We’re certified to service those and six more: LiftMaster, FAAC, BFT, Linear, Ghost Controls, and Mighty Mule. When a control board fails or a limit switch is acting up in 78108, we’ve usually got the part on the truck or can have it in hand within a day. Parts are useless if the frame isn’t plumb, though. We always check the post and hinge geometry before we blame the electronics, because that’s where Cibolo’s problems usually start.
Common Gate Parts & Welding Problems We See in Cibolo Homes
- Hinge posts shifted 2-4 inches out of plumb from clay heave. Swing gates bind at the latch, trip the operator’s force limit, and fail to close. The gate often looks fine. The post base tells the real story.
- HOA-approved gates with non-standard hinge spacing or custom rack mounts. Off-the-shelf replacement parts don’t fit without field welding or redrilling. We weld on site so the gate stays within architectural specs.
- Broken underground sensor wiring and misaligned photocells on community entry gates. Clay movement snaps or stretches buried loops and knocks beam eyes out of alignment, causing false obstructions during morning and evening rush.
- Bottom rails rusting at the factory welds. Cibolo’s summer heat plus wet-dry clay cycles means moisture sits at weld points long after the rain stops. We cut out the rot and weld in new steel rather than patching over it.
Pricing for Gate Parts & Welding in Cibolo, TX
Hinge replacement in Cibolo typically runs $185-$320. A single post reset with a deeper concrete pour and welded shim usually lands between $450-$900, depending on how much of the old footing has to come out. Rail repair runs $250-$550 for a cut-and-weld section, and custom bracket or rack welding starts around $150 and goes up with the complexity of the HOA-approved profile. Operator realignment after a post shift is $175-$375, including re-leveling the arm and adjusting limits.
The quote you get is the price you pay. We write it down before the torch comes off the truck, and we don’t tack on trip charges inside the county. Seniors and veterans get 10% off, permanently. Any repair over $200 gets $40 off. If you have a written estimate from another company, bring it. We’ll give you a free second opinion, and you might be surprised how often a gate that was quoted as a full replacement just needs a resession and a weld.
| Service | Typical Price in Cibolo |
|---|---|
| Hinge replacement (single gate) | $185-$320 |
| Single post reset with deeper footing | $450-$900 |
| Bottom rail cut-and-weld repair | $250-$550 |
| Custom welded bracket or rack mount | $150-$450+ |
| Operator realignment after post shift | $175-$375 |
Call (877) 610-2993 for an exact quote. The estimate is free, and the number you hear on the phone is the number on the invoice.
We Also Serve Cities Near Cibolo
If you’re in Schertz, Selma, Universal City, or Converse, the same crew that handles Gate Parts & Welding in Cibolo covers your area too. Same 90-Day Done Right Promise, same on-site welding, same live person on the phone. We coordinate scheduling from our San Antonio office, and most of the time, we’re in your driveway within a day or two of the call.
Serving Cibolo, TX - Our Local Coverage Area
We’re based in the Cibolo area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Cibolo
Yes, in nearly every Cibolo subdivision, the architectural committee must sign off before you change any visible gate structure, including the weld pattern on a replacement rail or the height of a new post. Most master-planned communities in 78108 require a written approval that references the community’s design standards, and that approval can take a week or two. We can weld to the exact profile the committee specifies, and we’ll wait for the paperwork rather than start work that gets you a violation letter. Call (877) 610-2993 to go over what your specific HOA requires.
Your gate post shifted because it’s set in Blackland Prairie clay, which swells when Cibolo gets rain and shrinks during drought. That cycle creates voids under shallow footings and tilts posts out of plumb. A 7-year-old gate with a 3-inch post shift is common along the FM 1103 corridor. The gate looks fine because the damage is below grade. We confirm it by checking the post base before touching any electronics. Call (877) 610-2993 and we’ll look at it for free.
If the post is still structurally sound and less than an inch or so out of plumb, yes, we can weld a new hinge or reinforcement plate onto the existing post and adjust the gate to match. If the post has moved two inches or more, resESSION the footing is the honest fix. Welding a new hinge to a heaving post just means you’ll call us again next spring. We’ll tell you which situation you have before we quote anything. Call (877) 610-2993.
Yes, and most Cibolo HOAs require both. The keypad handles entry for residents with a code, but the loop detector is what tells the gate a car is still in the swing path and prevents it from closing on a vehicle. If your community gate faults during backup at the FM 78 entrance, it’s usually the loop wiring, and clay movement is often what snapped it. We repair and replace loop detectors, photocells, and the welded mounting brackets that hold them. Call (877) 610-2993 to schedule an inspection.
We start by measuring the post’s plumb and the gate’s swing arc, then decide whether the post needs resetting or the operator arm just needs re-leveling. On a minor shift, we’ll weld a wedge plate or shim onto the mounting surface to get the arm parallel again and recalibrate the open and close limits. On a bigger shift, we reset the post first, because aligning an operator to a moving post is a waste of your money. Call (877) 610-2993 and we’ll tell you which fix applies before any work starts.
Call Gatewood Fence & Gate for Gate Parts & Welding in Cibolo
If your Cibolo gate is sagging, binding, or tripping its opener, we’ll come out, look at it, and tell you exactly what’s wrong and what it costs. The quote is free. The work is welded on site. The 90-Day Done Right Promise covers it in writing. Hal Gatewood has been at this since 2001, and his name is on the shop and on every invoice. Call (877) 610-2993 now, and a live person picks up.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Cibolo and surrounding communities since 2001.