Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Calabasas
Gate parts and welding in Calabasas usually means one of two things: a residential driveway gate that’s sagging or stalling, or a community entrance system that answers to an HOA board. We handle both, and we do most of the work right in your driveway or at the gate itself. Gatewood Fence & Gate has been owner-operated since 2001, and Hal Gatewood’s name is on the shop. When a gate in The Oaks or Calabasas Park Estates needs a hinge replaced, a post re-set, or a custom weld, we’re the ones who show up with a truck stocked for Calabasas specifically. Call (877) 610-2993 and you’ll get a live person, not a recording.
Why Gatewood Fence & Gate Is Calabasas’s Preferred Gate Parts & Welding Company
Most gate companies in Los Angeles County will look at a rusted hinge post on a 1998 wrought-iron swing gate and tell you to replace the whole gate. We won’t. Our Gate Parts & Welding crew welds on site, which means your gate stays in your driveway instead of getting hauled to a shop across the Valley. That matters in Calabasas, where the gates are heavier, the HOA standards are stricter, and the homeowners remember the last company that quoted $400 on the phone and billed $1,900 at the curb.
We answer every call with a live person, 24/7. Not a voicemail. Not a call center three states away. When a swing gate at Mulholland Estates won’t close at 9 p.m., the person who answers is going to understand why that’s urgent. Hal Gatewood founded this company in 2001 and still runs it himself. Crews are background-checked and uniformed. Every job, from a $180 hinge replacement to a full post re-set, carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings him back. No runaround.
Local Knowledge That Actually Matters in Calabasas
Calabasas is not Woodland Hills. The gates here are older, heavier, and governed by CC&Rs that most contractors never read. When we roll into Gate Parts & Welding in Calabasas, we already know the difference between a residential driveway gate off Mulholland Highway and a community entrance on Parkway Calabasas. That’s not a marketing line. It’s the difference between fixing a gate in one visit and scheduling three return trips.
Our Gate Parts & Welding Services in Calabasas
Hinge Replacement
Hinges on Calabasas gates take a beating. Santa Ana winds gust 50-70 mph through the passes at the foot of the Santa Monica Mountains, and every gust loads the hinges on a heavy iron panel. A worn hinge is rarely just a hinge. In Calabasas, we usually find the hinge post has rusted at the weld points too, especially on older gate installations in Calabasas from the mid-1980s to early 2000s. We replace the hinge, weld the post reinforcement if it needs it, and the gate swings true again.
Post Replacement
Here’s the thing most people get wrong: a gate sags in the post, not in the middle. If the post footing is failing, no hinge swap will fix it. We see this all over Calabasas, particularly at The Oaks, where original posts from the 1990s have rusted below grade where nobody can see it. We cut out the old post, set a new one in concrete, weld the panel back onto fresh steel, and send you photos of the work before it’s buried. Post replacement in Calabasas typically runs $400-$900 depending on post size and footing condition.
Rail Repair
Slide gates have a top and bottom rail that carries the panel along the track. After years of Santa Ana wind loads, powder-coated aluminum rails near Calabasas Park Estates warp just enough to let the rack skip teeth on the pinion gear. We straighten or replace the rail, check the rack alignment, and make sure the gate travels without binding. Sometimes the fix is a full rail replacement. Sometimes it’s a weld repair and realignment. We’ll tell you which one before we start, and the price won’t change at the end.
Custom Welding
Wrought-iron and steel gates in Calabasas are not interchangeable. A finial snapped off by wind debris, a decorative scroll cracked at the weld, a cracked hinge plate on a 2003 Gatecrafters unit: these are custom welding jobs, not parts-catalog swaps. We TIG and MIG weld on site, match the existing powder coat or paint as closely as the material allows, and hand you the piece back looking like it belonged there. Custom welding in Calabasas runs $150-$500 for typical repairs, more for structural reinforcement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Calabasas
We’re certified to service nine major gate brands, including Linear, Viking, Ghost Controls, and DoorKing. That’s not a catalog of logos. It means when a Linear operator on a 2004 Calabasas swing gate fails during a wind event, we know whether the board is salvageable or whether you’re better off retrofitting a modern Calabasas gate motor & opener that fits the existing mount. We keep common legacy parts on the truck for Calabasas specifically, because we know how many 20-35-year-old operators are still out here cycling through their second or third control board. Fast turnaround, no special-ordering a capacitor when your gate is stuck open.
Common Gate Parts & Welding Problems We See in Calabasas Homes
- Wind-warped slide gate rails: Santa Ana gusts through local passes warp powder-coated aluminum rails, causing the rack and pinion to skip teeth under load. The gate stalls halfway, then reverses. This isn’t a motor problem. It’s a rail and alignment problem.
- Rusted hinge posts at the weld points: Twenty-to-thirty-year-old wrought-iron swing gates at The Oaks rust where the hinge plate meets the post. Sag correction gets misdiagnosed as a panel issue when the post footing is the actual failure. Fix the panel without the post and you’ll fix it twice.
- Obsolete loop detectors from the 1990s: FAAC and Elite loop detectors from the original buildout fail intermittently at community entrances. The gate won’t hold open. The HOA calls. We replace the loop or the detector, but we also check whether the CC&R blocks swapping to modern non-matching hardware before we touch anything.
- Woolsey Fire damage grafted onto older infrastructure: The 2018 fire destroyed gates and wiring across large portions of the 91302 ZIP. Rebuilt properties now have new hardware bolted onto older posts and operators. We see wiring harnesses from 2019 connected to gate frames from 1992. It works until it doesn’t.
Pricing for Gate Parts & Welding in Calabasas, CA
Here are honest ranges for Calabasas, not vague estimates. Hinge replacement runs $180-$450 per hinge depending on the gate weight and whether we’re welding reinforcement. Post replacement runs $400-$900. Rail repair runs $250-$600. Custom welding runs $150-$500 for typical repairs. A full operator retrofit on a community entrance, including labor and a modern board, runs $800-$2,400 depending on the existing mount and what the CC&R allows. We quote the price up front, and that’s the price. No trip charge inside Los Angeles County. $40 off any repair over $200. Free second opinion on any written estimate you bring us. And a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Calabasas
We work throughout the western San Fernando Valley and the mountain communities around it. That includes Woodland Hills, West Hills, Las Flores, and Topanga. If your gate is in one of those areas, you’re still getting the same crew, the same 90-Day Done Right Promise, and the same live person on the phone at (877) 610-2993. Our Calabasas customers just happen to have the oldest gates and the strictest HOAs in the area, which is why we keep so many legacy parts on the truck.
Serving Calabasas, CA - Our Local Coverage Area
We’re based in the Calabasas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Calabasas
Sometimes, and we’ll tell you honestly before we start. Many Calabasas CC&Rs, especially at The Oaks and similar communities, prohibit swapping legacy FAAC or Elite operators for a different brand without a full board vote. That’s why we keep obsolete FAAC control boards and capacitors on our trucks. If we can rebuild the existing operator with a legacy board and reinforcement welding, we do that first and the board never has to vote. If a retrofit is the only real fix, we’ll prepare a written proposal you can take to your property manager. Call (877) 610-2993 and we’ll look at the gate before you schedule any board meeting.
Usually both. A gate sags in the hinge post, not in the middle. At Mulholland Estates, we regularly find 25-year-old hinge posts that have rusted at the weld points where the hinge plate meets the post. The panel gets blamed, but the footing is the failure. We’ll inspect the post, check the welds, and tell you exactly what needs replacing before we touch a single bolt. That’s the 90-Day Done Right Promise working, not a sales pitch.
Because the wind is loading the panel and the rail has warped enough to let the rack skip teeth on the pinion gear. When the gate moves into the wind, the motor pulls harder, the gear slips, and the safety circuit kicks in. You’re not imagining it. Calabasas slide gates from the early 2000s are especially prone because the original powder-coated aluminum rails were never meant for repeated 50-70 mph gusts. We straighten or replace the rail, check the alignment, and the stalling stops. Call (877) 610-2993 for a site visit.
Yes. Gatecrafters used a lot of FAAC and Linear internals during that era, and we’re certified on both. The challenge is sourcing specific boards that Gatecrafters discontinued years ago. We keep the common ones stocked. If your operator is beyond repair, we can often retrofit a modern FAAC or Linear unit with gate access control in Calabasas onto the existing mount, which usually satisfies CC&R requirements because the hardware stays manufacturer-consistent. We’ll walk you through the options and the board-vote reality before we quote anything.
We see three patterns consistently. First, hinge plates that warped from heat and need straightening or replacement. Second, post footings that were undermined by fire damage and are now settling, which requires re-setting the post and re-welding the panel. Third, wiring and operator mounts that were replaced with new hardware but grafted onto older steel, creating stress points that crack over time. Those are all weld-on-site jobs for us. The gate stays in Calabasas until it’s right.
If your gate is sagging, stalling, or making a noise it didn’t make last month, call (877) 610-2993. A live person answers. We’ll schedule a time, show up with the right parts, and quote the price before any work starts. Hal Gatewood has been doing this since 2001, and his name is on every invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Calabasas since 2001.