Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Arlington Heights
Gate parts and welding in Arlington Heights usually comes down to two problems: a post that frost has heaved out of square, or a weld that cracked during the off-season. We fix both on site, at your house, without hauling the gate back to some shop. Hal Gatewood has been doing this work since 2001, and we answer the phone with a live person at (877) 610-2993 when you call. If your swing gate is dragging, your slide gate won’t roll, or a hinge pulled loose from the post, we can usually get someone out to you within the same day.
Why Gatewood Fence & Gate Is Arlington Heights’s Preferred Gate Parts & Welding Company
We work throughout the 18360 ZIP and the lake-community roads around it, so we know what Monroe County winters do to a gate. The frost line here runs 36 inches deep or more, and a lot of these vacation-home gates were set in shallow footings back in the 1970s, 80s, and 90s. That means posts shift, welds crack, and hinges bind. None of that surprises us anymore.
Hal’s name is on the shop and on every invoice. Call us and a live person answers. That person can tell you what we’ll do, when we’ll be there, and what it will cost before we ever load the truck. We don’t hand your call to a phone tree. We hand you a straight answer. If the work isn’t done right, our 90-Day Done Right Promise means one call brings us back, no runaround. That’s in writing on every job.
We also hear from Arlington Heights homeowners who got a national company’s quote on the phone and a different number at the door. That’s not how we work. The price we quote is the price you pay, agreed before any work starts. You’ll see the same face at the hardware store that you saw in your driveway.
Our Gate Parts & Welding Services in Arlington Heights
Our Gate Parts & Welding crew handles the repairs that keep an older gate alive. In Arlington Heights, that usually means post work, hinge work, and custom welding rather than full gate replacement.
Hinge Replacement
Hinges on swing gates in Arlington Heights take a beating from freeze-thaw cycles. A hinge pin seizes, the leaf bends, or the weld breaks at the post. We replace the hinge and repair the mounting surface in one trip. If the gate is still sound, there’s no reason to replace it. We weld on site, so the gate never leaves your property.
Post Replacement
Around Arlington Heights, a gate rarely sags because the rail failed. It sags because the post moved. Many posts were set in shallow concrete footings that Monroe County’s frost heaves every winter. We dig the old post out, set the new one on a footing that goes below the 36-inch frost depth, and square the gate back up. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Bottom rails on swing gates drop and crack, especially where a driveway apron has heaved. We can weld reinforcement plates to a cracked rail, straighten a bowed section, or replace the rail if the steel is too far gone. On gates that have sat closed all winter, we often find the bottom rail has been dragging across a frost-heaved apron since March. That’s a standard catch here, not an add-on.
Custom Welding
Sometimes the part doesn’t exist anymore. Older ornamental iron gates from the 1980s weren’t built around today’s replacement catalogs. We weld brackets, patch cracked pickets, rebuild hinge plates, and fabricate small steel parts on site. If a hinge post pulled out and tore a chunk of the gate frame with it, we can weld a new mounting tab and get the gate hung again the same day.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Arlington Heights
We service and carry parts for the operators and gates we see most around Arlington Heights, including FAAC, Linear, and Viking. That covers a lot of the legacy swing-gate operators installed in Monroe County lake communities. If you’ve got an old FAAC control board with moisture damage, we can often get the replacement board or a compatible retrofit. For Linear and Viking slide-gate operators, we keep common rollers, limit switches, and receiver parts on the truck. Our Gate Parts & Welding in Arlington Heights service is built around getting your gate working again without waiting on a parts warehouse across the country.
Common Gate Parts & Welding Problems We See in Arlington Heights Homes
Here’s what we run into most often on gates in the 18360 ZIP and the roads around the lake communities:
- Frost-heaved posts. Shallow footings shift every winter, cracking the hinge welds and racking the gate out of alignment. By April, a swing gate that worked fine in October won’t latch or won’t open at all.
- Seized rollers on slide gates. Gates in seasonal communities sit unmaintained from November to May. Water gets into the roller bearings, rust sets in, and the gate grinds to a stop on its first open of the season.
- Obsolete control boards. An old LiftMaster or FAAC operator with a dead battery backup and moisture in the keypad often fails right when the owner returns. We diagnose what’s salvageable before recommending anything.
- Cracked hinge welds on ornamental iron. Older iron gates weren’t designed for decades of freeze-thaw flex. The welds at the post side are usually the first thing to crack.
Last spring, a call came from a gated lake-community home off a winding road in Arlington Heights. A swing gate’s bottom rail had dropped into a frost-heaved driveway apron and the hinge post had pulled out of its footing, racking the gate so hard the LiftMaster operator’s safety photocell had faulted. We reset the post on a 42-inch footing, welded reinforcement plates to the cracked rail, and rewired the keypad entry after confirming the operator’s entrapment protection was functioning. One trip covered the full post reset, sag correction, and operator service. That’s standard here, not upsell.
Pricing for Gate Parts & Welding in Arlington Heights, PA
Here are honest ranges for the work we do in Arlington Heights:
- Hinge replacement, single swing gate: $180-$340
- Post replacement (set below 36-inch frost line): $450-$900 depending on post size and gate weight
- Rail repair and reinforcement welding: $220-$520
- Custom welding (brackets, tabs, picket patches): $150-$400 per job
- Roller replacement for slide gates: $120-$280
What moves the number is how much digging and welding is actually required. A post that pulled out of a shallow footing costs more than a hinge swap. A rail that needs full replacement costs more than a weld reinforcement. We quote the job before any work starts, and you get $40 off any repair over $200, plus no trip charge inside the county. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Arlington Heights
Our gate repair and welding service covers Arlington Heights and the surrounding towns, including Bangor, Nazareth, Easton, and Palmerton. If your gate is in one of those communities, the same crew, the same parts, and the same 90-Day Done Right Promise apply. Call us and we’ll let you know when we can get there.
Serving Arlington Heights, PA - Our Local Coverage Area
We’re based in the Arlington Heights area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Arlington Heights
Because the post footings are heaving. Monroe County’s frost line runs 36 inches or deeper, and many Arlington Heights gates were set in footings shallower than that. The freeze-thaw cycle moves the post a fraction of an inch each winter, which translates to a gate that racks out of square by spring. The permanent fix is resetting the post below frost depth, not re-hanging the gate on the same shifting footing. Call (877) 610-2993 and we’ll come look at what’s moving.
In most cases, yes. An older LiftMaster operator can often accept a retrofit photocell set and updated entrapment protection without replacing the whole operator. We check the control board’s compatibility first, because some obsolete boards from the 1990s don’t support modern sensor wiring. If the board is still sound, retrofitting is usually the cheaper answer. Call us for a straight assessment.
Almost always the post. A gate sags in the hinge post, not in the middle, and that’s where we start. The rail takes the blame, but the post moved first. Around Arlington Heights, frost heave is the most common cause. We check post plumb, hinge wear, and rail condition before quoting anything, so you’re not paying for a rail repair that won’t hold.
Open the gate manually and listen. A grinding or rumbling sound at the track means the roller bearings have rusted or seized. If the gate binds partway through travel and won’t roll smoothly, the rollers are shot. In Arlington Heights, gates in seasonal lake communities go months without moving, and moisture in the bearings does the damage. We replace rollers and clean the track in one visit. Don’t force the gate open with the operator, because a seized roller can burn out the motor. Call us at (877) 610-2993 and we’ll diagnose it before it gets worse.
You don’t need to be home. Many of our Arlington Heights customers are only here from May to October, and we regularly handle post resets and hinge replacements while the owner is out of state. We’ll walk you through the quote by phone, confirm the work order, and send photos when the job is done. Price is agreed before any work starts, so there are no surprises when you get back.
Call Gatewood Fence & Gate for Gate Parts & Welding in Arlington Heights
If your gate is dragging, sagging, or not opening at all, call (877) 610-2993. We’ll answer with a live person, not a voicemail. Hal Gatewood leads every job, and his name is on the shop and on your invoice. You get upfront pricing, on-site welding, and the 90-Day Done Right Promise in writing. If you’re in Arlington Heights or any of the surrounding towns, one call gets the gate fixed the right way.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Arlington Heights since 2001.