Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in West Memphis, AR
A gate that won’t close in West Memphis is usually a security problem, not just an annoyance. Most calls we get start the same way: the gate swung fine last fall, but by spring it’s dragging across the driveway or missing the latch by an inch. That’s the Delta gumbo clay doing what it does-swelling when saturated, shrinking when dry, and pushing your post out of plumb while you sleep. We answer the phone with a live person at (877) 610-2993 any hour of the day, and we’ll give you a straight answer on when we can be there.
Why West Memphis Homes Are Different
West Memphis sits on the Mississippi River alluvial floodplain, and the soil underneath most of the city is buckshot gumbo clay. It swells hard when the water table rises, then cracks and shrinks during dry spells, and that cycle repeats every year. A gate post set without extra depth and proper drainage will heave, tilt, and lose plumb fast. The low-lying lots near the I-55/I-40 interchange and the older neighborhoods closer to the river see this every spring-gates that closed in October won’t latch by April because the clay has shifted the post outward a full inch.
The housing stock makes it worse. Most homes in the 72301 and 72303 zip codes were built between the 1940s and 1970s, and chain-link dominates the fences. Many of those gates are original or close to it, with decades of deferred maintenance. The river-bottom humidity accelerates rust at hinge pivot points and ground-level frame sections. We regularly find gates in Holiday Park and along the Mound City Road corridor where the frame has rusted through at the concrete line but the homeowner never noticed until the gate sagged.
Gate Repair in West Memphis
Gate repair in West Memphis almost always involves soil movement. The gumbo clay under your lot is the first thing we check, because it’s the first thing that fails. A typical hinge replacement or gate re-hang runs $180-$320. Post re-setting and re-plumbing, which is the most common repair here, typically lands between $250 and $475 depending on depth, concrete condition, and whether the post needs a new footing. Every price is quoted in writing before we start, and that price doesn’t change at the door.
Electric Gate Repair
Electric gates in West Memphis take a beating from humidity and the constant rumble of trucks off I-55 and I-40. When a board fails or a capacitor burns out, we trace it, test it, and replace only what’s dead. We service Viking, DoorKing, Ghost Controls, and Elite opener systems, and we’ll tell you straight if the box can be rebuilt instead of replaced. Electric gate board or capacitor replacement runs $175-$400 for most residential systems. In most cases we can have your opener running the same day.
Hinge & Post Repair
This is the repair we do most in West Memphis, and for a reason people here know well. The Delta gumbo clay under your lot swells when it rains and shrinks when it dries, and that cycle pushes gate posts out of plumb fast. A gate sags in the hinge post, not in the middle, and that’s where we start. We re-set posts, re-plumb them, weld hinge plates back square, and re-hang the gate so it swings like it should. Post re-setting and re-plumbing typically runs $250-$475.
Gate Realignment
When your gate won’t latch or drags across the concrete apron in front of your house off Broadway or Rich Road, the gate has moved and the frame hasn’t. We re-align gates in West Memphis driveways regularly, often as part of post work. Fixing the panel without the post means you’ll fix it twice, so we do the post first and the panel second. A full gate realignment with latch adjustment typically falls between $150 and $275. The result is a gate that closes and latches with one hand.
We handle all types of Gate Repair in West Memphis, from chain-link re-hangs to ornamental iron weld repairs.
How fast can you get to my house in West Memphis?
Most calls inside the 72301 and 72303 zip codes get same-day service when you call before early afternoon, and we run emergency calls around the clock. A live person answers the phone 24/7, and for urgent jobs like a gate stuck open, we’ll get someone out fast. Call (877) 610-2993 and we’ll give you a straight answer on when we can be there.
Why does my gate opener work fine in October but bind every April?
It works in October because the gumbo clay has dried and shrunk, pulling away from the post. Every April, the spring water table rise re-saturates that clay, swelling it against the footing and pushing the hinge post outward. That outward shift binds the rack and pinion, which forces the motor to work against extra resistance until the gears strip or the overload trips. The fix is resetting the post in a deeper footing with crushed stone drainage before remounting anything. Call (877) 610-2993 for a free estimate.
Gate Installation in West Memphis
New gate installation in West Memphis usually runs $1,200 to $4,800 depending on style, size, and material. Most standard driveway gates land between $1,800 and $3,200. If you live here, you already know the ground doesn’t sit still. That’s why we treat every new install as a job where the post is the project, not the gate. We set posts deep enough with proper drainage to hold against the gumbo clay, so your gate stays plumb through the wet spring, not just on install day.
Driveway Gate Installation
A driveway gate in West Memphis is usually the first thing people see from the road. We build and hang steel frame, ornamental iron, and chain-link driveway gates sized to your opening, and we set the posts deep enough to hold against the gumbo clay. A single driveway swing gate in steel frame typically runs $1,800-$3,200 installed, while a double driveway swing gate runs $2,800-$4,800. If you want a gate that swings or slides, we’ll match the hardware to how your driveway drains.
Pedestrian Gate Installation
Pedestrian gates get the most abuse because they’re opened and closed dozens of times a day. We install them with heavier post settings and welded frames so they don’t sag in the first two years. On the mid-century homes around West Memphis, most existing pedestrian gates are chain-link and rusted at the pivot points. A new pedestrian chain-link gate installed with proper post depth typically runs $450-$900, including post and hardware.
Sliding Gate Installation
Sliding gates make sense on West Memphis properties where the driveway slopes toward the house or where there isn’t room for a swing arc. We install track and cantilever sliding gates, and the track matters more than most people realize. Wet seasons here leave silt on the ground, and a poorly set track clogs and binds. A sliding driveway gate typically runs $2,200-$4,200 installed, depending on track length and gate weight. Hal’s crew welds on site, so the gate is built to your actual opening, not a template.
For more details on materials and scheduling, see our Gate Installation page.
Why does gate installation cost more in West Memphis than in drier Arkansas towns?
It mostly comes down to the soil. The gumbo clay in the bottomland requires deeper post settings and sometimes concrete collars to hold against seasonal heave, which is more labor than a standard post hole in drier upland soil. In West Memphis you’re paying for a gate that stays plumb through a wet spring, not just one that looks right on install day. Call (877) 610-2993 for a written price before any work starts.
What does your warranty cover on a new gate installation in West Memphis?
Every job carries Hal’s 90-Day Done Right Promise in writing. If something’s not right within 90 days, one call brings him back. That covers the installation workmanship and the hardware we supplied. If a post shifts, a hinge binds, or a gate doesn’t latch right, we make it right. No fine print, no runaround. Call (877) 610-2993 and we’ll come take a look.
Gate Motor & Opener in West Memphis
A gate motor or opener repair in West Memphis usually costs between $225 and $520, and most jobs are completed the same day we arrive. If your swing gate stopped responding or your slide gate is binding after heavy rain, the problem usually comes down to one thing: the post shifted in the gumbo clay. That’s the first thing we check, because it’s the first thing that fails here. We don’t replace motors that are still good-we fix what’s actually broken.
Motor Installation
Installing a gate motor in West Memphis means accounting for wind load on solid infill gates, especially on properties closer to the river where storms hit harder. We size the operator to the gate’s actual surface area and weight, not just a generic horsepower chart. A typical motor installation here runs $1,100-$2,400 depending on gate width and whether we’re adding a new operator arm or reusing existing hardware. Before we touch anything, you get a written price. Nothing changes at the door.
Motor Repair
Most motor repair calls in West Memphis start with a post check. The Delta clay swells after rain and shrinks during dry spells, and that movement torques the operator bracket, binds the rack and pinion, and eventually strips gears or trips the overload. We re-plumb the post, reset the operator alignment, and only then replace what actually failed. A typical motor repair runs $225-$520, with $40 off any repair over $200. The quote is agreed before any work starts.
Slide Motor Service
Slide gates in West Memphis have a specific enemy: gumbo clay pushing against the footing and twisting the track. When the track flexes even a quarter inch, the gate chatters, the rollers wear uneven, and the motor’s amperage spikes. We reset the track on compacted crushed stone, re-level the rollers, and verify the motor isn’t drawing beyond its rated load. Slide motor repair generally runs $250-$550. We quote it before we start, and we stand behind it for 90 days.
We service all major brands-learn more on our Gate Motor & Opener page.
Can you install a battery backup on my existing opener in West Memphis?
Yes, we can add a battery backup to most major brands. In West Memphis, where Delta storms knock out power regularly and gates get forced open by hand in the dark, battery backup pays for itself after one outage. Installation typically runs $350 including the battery and wiring. We stock compatible backup units for LiftMaster, FAAC, and Linear operators, so the job usually happens same day. Call (877) 610-2993 to check compatibility.
Why does my slide gate motor trip the breaker after heavy rain near the interchange?
Heavy rain on low-lying lots near the I-55/I-40 interchange means standing water, and standing water means a saturated ground track and a motor pulling more amperage than it should. Water gets into the motor housing or the conduit connections, the ground fault trips, or the overload protection kicks in because the gate is dragging against a wet, misaligned track. We dry out and seal the electrical connections, re-level the track, and quote everything before we start. Call (877) 610-2993.
Gate Access Control in West Memphis
Access control in West Memphis has to survive the same conditions that kill gates and motors: humidity, ground shift, and the occasional flood. We install and repair keypads, remotes, intercoms, and telephone entry systems that hold up to the river-bottom climate. A typical keypad or remote receiver installation runs $450-$1,100 depending on wiring distance and whether we’re trenching through gumbo clay or working with existing conduit.
Keypad & Intercom Installation
Keypads mounted on posts in West Memphis need sealed housings rated for the humidity here, and the post itself needs to be set deep enough that it doesn’t heave out of alignment. We see plenty of keypads that worked fine in dry weather but failed after the first wet season because water got into the contacts. We use marine-rated enclosures and seal all penetrations. A new keypad or intercom installation with proper post setting typically runs $450-$850.
Telephone Entry & Remote Systems
Telephone entry systems let you buzz visitors in from inside the house, which matters on properties where walking to the gate in a thunderstorm isn’t appealing. We wire these with underground cable rated for wet locations, and we test the full path before we leave. Remote receiver upgrades and multi-button transmitters typically run $350-$650 installed. If your existing system is intermittent, we check the antenna placement first-humidity can corrode connections that look fine on a dry day.
For more on access control options, visit our Gate Access Control page.
Will a keypad survive the humidity and flooding in West Memphis?
Yes, if it’s installed right. We use sealed, marine-rated keypads and mount them on posts set deep enough to resist heave. We also seal every wire penetration and use underground-rated cable. Cheap keypads mounted on shallow posts with exposed connections fail fast here. We do it once and do it right, with the 90-Day Done Right Promise behind it. Call (877) 610-2993 for a free estimate.
Can you add remote access to my existing gate opener?
In most cases, yes. We can add a remote receiver to most major brands, including LiftMaster, Linear, and FAAC systems. The receiver needs clean power and a stable mounting location, which means checking the operator bracket first-if the post has heaved, the receiver antenna won’t align right. Receiver installation typically runs $350-$650. Call (877) 610-2993 and we’ll tell you if your system is compatible.
Gate Parts & Welding in West Memphis
We weld on site in West Memphis because hauling a gate to a shop and back costs you money and time you don’t have. Our truck carries a portable welder, cutoff saw, and stock steel, so we can repair a rusted frame, fabricate a new hinge plate, or extend a post right in your driveway. On-site welding repair typically runs $120-$280 depending on rust damage and material needed. We also stock common parts-hinges, rollers, latches, chain-link hardware-so most jobs don’t wait on an order.
On-Site Welding
When a gate frame rusts through at the ground line or a hinge plate tears off the post, the fix is welding, not replacing the whole gate. We cut out the rotted section, fit new steel, and weld it solid while the gate stays where it is. This is especially common on the older chain-link gates around West Memphis, where decades of humidity have eaten the frame from the bottom up. A typical frame weld repair runs $120-$280, and we treat the repair so it doesn’t come back next year.
Parts & Hardware
We carry hinges, rollers, latches, chain-link fittings, and operator hardware on the truck, and we can source specialty items for Viking, DoorKing, and Elite systems within a day or two. If your gate needs a part we don’t have, we’ll tell you upfront how long it takes and what it costs-no surprises. Most hinge replacements and hardware swaps in West Memphis run $80-$160 including labor, and we don’t charge a trip fee inside the county.
See our full Gate Parts & Welding capabilities.
Can you weld my rusted chain-link gate instead of replacing it?
Usually, yes. If the frame has localized rust at the ground line or a hinge point, we cut out the bad section and weld in fresh steel. We do this regularly on the mid-century chain-link gates common in West Memphis. If the frame is rotted through more than 30 percent of its length, we’ll tell you straight that replacement makes more sense. Either way, you get a written price before we strike an arc. Call (877) 610-2993.
Do you stock parts for older gate brands?
We stock hardware for the nine major brands we service, including Viking, DoorKing, and Elite, and we can source discontinued parts through our supplier network. For the older gates common in West Memphis, we often fabricate a replacement part on site rather than hunting for an exact match. That saves you time and money, and it’s why we carry the welder. Call (877) 610-2993 with your brand and model.
Brands We Service in West Memphis
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for Viking, DoorKing, and Elite locally, which means faster turnaround on repairs for those systems. For a full list of what we service and stock, see our brands page.
Pricing for Gate Repair in West Memphis, AR
| Service | Typical range in West Memphis |
|---|---|
| Hinge replacement or gate re-hang | $180-$320 |
| Post re-setting and re-plumbing | $250-$475 |
| Electric gate board or capacitor replacement | $175-$400 |
| Gate realignment with latch adjustment | $150-$275 |
| On-site frame weld repair | $120-$280 |
| Single driveway swing gate (steel frame) | $1,800-$3,200 |
| Double driveway swing gate | $2,800-$4,800 |
| Sliding driveway gate | $2,200-$4,200 |
| Pedestrian chain-link gate | $450-$900 |
| Gate motor installation | $1,100-$2,400 |
| Gate motor repair | $225-$520 |
| Keypad or intercom installation | $450-$850 |
What pushes the price up in West Memphis is almost always the ground work. Gumbo clay requires deeper post settings, better drainage, and sometimes concrete collars that drier soils don’t need. Every price we quote is agreed in writing before any work starts, and that number does not change at the door. We don’t charge a trip fee inside the county, and we offer $40 off any repair over $200 plus a permanent 10% discount for seniors and veterans.
Neighborhoods We Serve in West Memphis
We run trucks throughout West Memphis and response in Crittenden County is typically same-day on weekdays with emergency availability nights and weekends. Here are the areas we’re in most often:
- Holiday Park
- Mound City Road corridor
- Old Town and streets near Missouri Street
- Subdivisions off North Avalon in 72301
- Lakeview and Meadowbrook areas
Service Area - Cities Near West Memphis
We cover all of West Memphis in the 72301 and 72303 zip codes, and we also serve Marion, AR and surrounding Crittenden County communities. Dispatch and scheduling are coordinated from our Memphis office, but crews serve West Memphis, AR locally with no trip charge inside the county.
Serving West Memphis, AR - Our Local Coverage Area
Gatewood Fence & Gate crews serve West Memphis and the communities around it; dispatch is coordinated from our Memphis office. The map shows the West Memphis coverage area; if your address is on it, we can help.
Also serving nearby: West Memphis, AR, Marion, AR.
FAQs About Gate Repair in West Memphis
Most residential gate repairs in West Memphis don’t require a permit, but new installations and any work that modifies the fence line or adds electrical service may need approval from the city. We know the local requirements and will tell you upfront if your job needs a permit. If it does, we handle the paperwork as part of the job. Call (877) 610-2993 and we’ll walk you through it.
Listen first. If the motor runs but the gate doesn’t move, or if the gate moves partway and stops, the opener is probably fine and the post has shifted. If the motor hums but nothing happens, the motor may be stripped. In West Memphis, we always check the post first because the gumbo clay causes more failures than the motor does. Call (877) 610-2993 and we’ll diagnose it properly.
Yes, every estimate is free and comes with no obligation. We’ll come out, look at the gate, check the post and the soil, and give you a written price before any work starts. We also offer a free second opinion on any written estimate you’ve already received. Call (877) 610-2993 to schedule a time that works for you.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What West Memphis Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath