Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Irvington, NY
Gate repair in Irvington typically costs $180-$340 for hinge and alignment work, $220-$500 for electric gate repairs, and $650-$1,200 when a brick pillar needs rebuilding. Most calls are same-day or next morning, because a broken gate on a narrow urban lot means an unsecured property overnight. Call (877) 610-2993 and a live person picks up, 24 hours a day.
Irvington’s pre-WWII housing stock, freeze-thaw cycles, and the aging wrought-iron gates from the late-1990s security push make this town’s gate problems different from anywhere else in Essex County. We’ve been at this since 2001, and Hal Gatewood still answers his own phone.
Why Irvington Homes Are Different
Irvington sits in the 07111 ZIP code with a dense concentration of 1910s to 1950s two-family homes and attached rowhouses on narrow concrete or brick driveways. The housing stock matters because these gates weren’t installed yesterday. Most are single- or double-leaf swing designs bolted into brick pillars that have settled for seventy or eighty years, and the freeze-thaw cycle here is relentless. Water gets into hairline cracks, freezes, expands, and heaves the post a fraction of an inch. Do that for twenty winters and the gate frame racks out of square.
The late-1990s crime-deterrence push added another layer. A significant share of Irvington properties got wrought-iron driveway gates installed during that era, and those gates are now 20-25 years old with original hinges and latches that are seizing or shearing. Matching period hardware is no longer stocked by suppliers, so what looks like a simple hinge swap often turns into a full hardware overhaul. Summer humidity then accelerates rust on any iron with compromised paint or stressed welds. We see this pattern most often around Springfield Avenue, Chancellor Avenue, and the Union Avenue neighborhoods.
Gate Repair in Irvington
Gate repair in Irvington almost always comes down to one of three things: a gate that won’t open, a gate that won’t stay closed, or a gate that’s sagging so badly it’s carving a groove in the concrete. The housing stock and climate here mean the fix usually starts below ground level, with a post or footing that moved, not with the gate itself. Gate Repair is what we do most in this township, and we’ve learned to diagnose the structure before we touch the hardware.
Hinge and Post Repair
This is the heart of what we do in Irvington. The township’s 1910s-1950s housing stock means gate posts are bolted into brick pillars or set in footings that have been through 70-plus Essex County winters. Brick spalls, mortar crumbles, the post leans, and the gate starts binding. We rebuild the pillar base, reset the post with fresh concrete, and weld or bolt on new hardware sized to the actual leaf weight. A gate sags in the hinge post, not in the middle, and that’s where we start. A full hinge and post repair where the brick pillar needs rebuilding lands between $650 and $1,200 depending on the pillar damage and leaf weight.
Electric Gate Repair
When an electric gate in Irvington stops responding, the first thing we check is whether it’s a motor problem or a structural problem. About half the time it’s both. A gate that’s out of alignment puts load on the operator, burns out the board or the capacitor, and you’re left thinking you need a new motor when the real issue is a post that heaved two inches over the winter. We diagnose the whole system before replacing anything. Electric gate repairs, a failed capacitor, board, or limit switch, typically run $220-$500 in parts and labor.
Gate Realignment
On narrow Irvington lots, a gate that’s out of alignment by an inch and a half will scrape the driveway, bind against a brick wall, or fail to latch because the catch bar no longer lines up. Realignment isn’t just cranking hinges. It means checking the post plumb, checking the leaf camber, and sometimes adjusting the hinge-side post so the latch side lands true. We do this on swing gates and sliding gates both. Gate realignment runs $180-$350 when the posts are sound.
Why do so many Irvington driveway gates sag after winter?
Irvington gate posts are set in footings that heave from Essex County’s freeze-thaw cycles each winter. Water seeps into the footing or the brick pillar base, freezes, expands, and pushes the post out of plumb. The gate then sags because the hinge post moved. Most springs we find posts that shifted a half-inch to two inches. The fix is resetting the footing with fresh concrete and rebuilding damaged pillar brick.
My Irvington gate dates from the late 1990s and the hinges are seizing. Do I need a full replacement?
Usually not. Irvington’s late-1990s crime-deterrence gates are now 20-25 years old with original hinges that are seizing or shearing. Matching period hardware is no longer stocked by suppliers, so we machine or source equivalent heavy-duty hinges and weld or bolt them on. You keep the gate, lose the problem. A full replacement is only warranted when the gate frame itself is rusted through beyond a safe weld repair. Call (877) 610-2993 for a free look.
Gate Installation in Irvington
New gate installation in Irvington usually runs $2,800-$6,400 for a single-leaf driveway gate, and a properly hung double swing gate on new posts lands between $4,500 and $9,000, depending on ironwork and automation. Most Irvington jobs take one to three days once materials are ordered, and we coordinate scheduling from our New York City office while crews work locally in Irvington every week. Gate Installation here demands measuring the actual opening, not pulling from a catalog, because these narrow driveways don’t forgive a sloppy fit.
Driveway Gate Installation
A new driveway gate in Irvington typically runs $3,200-$8,500 installed, with the spread depending on single versus double leaf, ironwork weight, and whether we’re replacing posts or working with existing masonry. On the narrow concrete driveways between Springfield Avenue and the older rowhouse blocks, we size gates to the actual opening, not a catalog. Most Irvington driveways can’t fit a sloppy four-inch gap on either side.
Pedestrian Gate Installation
Pedestrian gates in Irvington usually land between $1,400 and $3,600, including posts, hinges, latch, and concrete work. These are the gates people use every day, and the ones most likely to be hanging crooked because the original installer set a post in three inches of concrete. We set footings below the frost line so the freeze-thaw cycles that hit Essex County every winter don’t shove your gate out of square by February.
Security Gate Retrofit
Security gates in Irvington deserve a separate mention, because a meaningful number of the gates installed here went up during the late-1990s community crime-deterrence push. Those gates were heavy, and they were meant to be a barrier. If you’re replacing one, we spec the frame, hinges, and operator for daily hard use, not curb appeal. A security gate that sags after eighteen months isn’t security. It’s a liability. A security gate retrofit with safety upgrades and a new operator typically runs $1,900-$4,500.
Why does my Irvington gate keep sagging after a simple hinge replacement?
Because the hinge isn’t the problem. In Irvington, the freeze-thaw cycle heaves the brick pillar or concrete footing, which racks the entire gate frame out of alignment, and new hinges just wear out faster against the same misalignment. We repair the post or footing first, then reset the gate with sag correction brackets. Fix the panel without the post and you’ll fix it twice.
Can a 1990s-era Irvington wrought-iron gate be retrofitted with a modern safety system?
Yes, most 1990s-era Irvington wrought-iron gates can be retrofitted with modern photo-eyes, safety edges, and a new operator without replacing the gate itself, as long as the frame and hinges are sound. We do this all the time on the old security gates off Clinton Avenue and Ellis Avenue. The gate leaf usually stays in place while we weld new hardware brackets, add entrapment protection, and swap the operator. Call (877) 610-2993 to schedule a free measure and written quote.
Gate Motor & Opener in Irvington
If your driveway gate in Irvington won’t open, grinds halfway, or just sits there humming, you want the person who shows up to already know the difference between a tired capacitor and a stripped gear. Gate Motor & Opener work here is structural before it’s electrical, because Essex County’s freeze-thaw cycles push brick pillar footings and gate posts up and out of line every winter. The motor then works harder every cycle until it burns out.
Motor Repair
A motor that runs but won’t move the gate is usually binding against a shifted post or a seized hinge, especially on the older swing gates common off streets like Springfield Avenue. We diagnose the whole drive train, not just the motor. If the armature, capacitor, or limit switch is done, we replace the part and re-tune the opener to the gate’s actual weight and travel. A typical motor repair, replacing a capacitor or limit switch and re-tuning the opener, runs $260-$620.
Motor Installation
When a 20-year-old opener’s control board is obsolete and no longer sourced, repair stops making sense. We install modern operators sized for the gate leaf, with safety photocells and battery backup where the property needs it. On Irvington’s narrow driveways we often recommend a slower, higher-torque operator rather than a fast residential swing kit, because a heavy wrought-iron leaf on two 100-year-old brick pillars moves differently in February than it does in August. A full opener replacement for a single-leaf swing gate runs $1,100-$1,800, and a double-leaf wrought-iron gate with heavier operators runs $1,800-$2,800.
Slide Motor Service
Slide gates hold their own set of problems. A slide motor that strains or trips its breaker is often trying to drag a gate whose roller trucks are pitted or whose rail has settled out of level. In Irvington, where freeze-thaw cycles move buried footing pads a quarter inch every decade, that drift adds up. We correct the gate path first, then set the motor’s torque limits correctly so it isn’t fighting the frame. That’s the difference between a slide motor that lasts three years and one that lasts fifteen.
Why does my Irvington swing gate motor keep burning out after winter?
Because the pillar has moved and the motor is fighting the gate. Irvington’s freeze-thaw cycles heave the footing under the hinge post, the gate leaf sags a half inch, and the motor draws more current every cycle until it burns out. Replacing only the motor without fixing the post means you’ll replace it again in two winters. We start with the post. That’s the actual repair.
Can you add battery backup to an existing Irvington gate opener?
Yes, in most cases. We can retrofit battery backup to nearly any modern AC-powered gate opener, including 1990s-era units that are still running. The battery cabinet mounts beside the operator and takes over during power outages, which matters in Irvington where summer storms and winter ice both knock out grid power. We’ll confirm your specific opener model is compatible during the estimate. The add-on runs $350-$750 installed. Call (877) 610-2993 to check yours.
Gate Access Control in Irvington
Gate access control in Irvington is rarely a simple swap-out. The township’s pre-WWII two-family homes and rowhouses, built tight against each other on narrow lots off Clinton Avenue and Springfield Avenue, mean most jobs involve retrofitting modern keypad entry or phone entry onto aging swing gates whose hinge posts have shifted inside cracked brick pillars. Gate Access Control here starts with stabilizing the masonry, then mounting the electronics.
Keypad Entry
A keypad mounted on a brick pillar in Irvington has a specific failure pattern: freeze-thaw heave cracks the mortar, the mounting screws loosen over two or three winters, and the keypad loses its ground to the operator. Then intermittently the code doesn’t open the gate, usually at the worst possible time. We don’t just screw it back in; we reset the mounting with stainless anchors and grout, then calibrate the operator so the gate’s travel is true again. Typical keypad entry repair or install in Irvington runs $350-$900.
Phone Entry
Phone entry is the most common retrofit request we get from Irvington landlords and owner-occupants alike. A 1990s-era phone entry box, usually DoorKing or Linear, has lasted twenty-five years and is now corroded inside. In summer humidity, oxidized conduit loses ground, and the system opens the gate on its own, or doesn’t open it at all. We replace the control board, re-pull the low-voltage wire where it’s rotted, and tie it into the existing gate operator. Phone entry installation starts around $900 and goes to $2,200 depending on the gate and wiring condition.
Remote Control
Remote control access issues in Irvington are often less about the remote and more about the receiver location. On tight shared driveways where the gate operator sits behind a brick wall or under a carport, the antenna picks up interference from neighboring WiFi and the signal drops. We relocate receivers, add external antennas where the operator model allows it, and reprogram rolling-code remotes so a tenant’s old remote doesn’t keep opening the gate after they move out. Remote replacement or reprogramming runs $150-$400 for a single-digit setup.
Can you retrofit a modern keypad entry onto an Irvington brick pillar that has shifted?
Yes, and this is exactly the kind of job we do most in Irvington. The key is that the pillar has to be stabilized before the keypad will hold calibration. We reset the pillar footing or repoint the mortar, set stainless anchors, mount the new keypad, and then tune the operator to the gate’s true travel. If you skip the masonry, the keypad will drift out of alignment in a season.
Our shared driveway gate has two keypads, and the tenant pad works but the owner pad doesn’t. Can you fix only the access control?
Yes, that’s an access control repair, not a gate repair. Nine times out of ten, one keypad has lost its ground or its wiring has been compromised at the pillar. We test the good pad, trace the bad pad’s line, and either repair the connection or swap the pad. The gate itself is fine. This kind of repair in Irvington usually runs $350-$700. Call (877) 610-2993 and we’ll sort it out.
Gate Parts & Welding in Irvington
When a driveway gate in Irvington won’t close or a hinge shears off its post, the problem is rarely just the broken piece you can see. The real issue is usually years of Essex County freeze-thaw movement working on old iron and aging masonry at the same time. Fix the hinge without checking the post, and you’ll be back in the same spot next spring. Gate Parts & Welding is where we handle both sides of that equation, with on-site welding so the gate stays in your driveway.
Hinge Replacement
Hinges are the first thing to go on Irvington gates, especially the originals from the late 1990s and early 2000s that are now 20-plus years old. We remove the seized hardware, check the post surface underneath, weld in new hinges rated for the gate’s weight, and cut the old ones off clean. In Irvington, hinge replacement usually runs $180 to $320 per hinge, which includes grinding, welding, and paint touch-up. If the hinge has pulled away from the brick, that’s when we recommend checking the pillar itself before we weld anything new to it.
Post Replacement
Freeze-thaw cycles in Essex County push concrete footings up a little more each winter. When a post heaves, the gate starts dragging at the latch end or scuffing the driveway. We core out the old anchor, set a new steel post, weld the gate hinges back, and repair the masonry around it. Post replacement in Irvington averages $550 to $1,150, and the range depends mostly on whether the brick pillar needs rebuilding. On the older two-family properties where pillar brick is original from the 1920s, we almost always rebuild at least the top course.
Custom Welding
Sometimes the part simply doesn’t exist anymore. We fabricate gate hinges, latch plates, ornamental scroll ends, and steel brackets on-site when matching period hardware is no longer stocked by suppliers. If a decorative finial broke off an older gate or a gate stop sheared from its post, we’ll shape and weld a replacement that won’t look like a patch job. Custom welding around Irvington typically runs $140 to $380 per fabricated piece, quoted before we strike an arc.
Why does gate welding cost more in Irvington than in nearby towns?
It doesn’t have to. Our pricing in Irvington is the same upfront structure we use countywide, but the older brick pillars and tight driveways here mean some jobs legitimately take longer. The estimate accounts for masonry repair and limited access, not a city premium. You’ll know the number before we start, and it’s the number on the invoice.
Can you match the decorative ironwork on an old Irvington gate?
In most cases, yes. We shape and weld replacement scroll ends, finials, and brackets on-site to match the existing gate, and we prime the repair so it doesn’t flash rust before painting. If the piece is heavily ornamental cast iron rather than wrought steel, we’ll tell you honestly whether it should be repaired or replaced before we recommend cutting into it. Call (877) 610-2993 to show us what you’ve got.
Brands We Service in Irvington
We carry parts and service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Irvington’s older stock, we most often see Linear, Viking, and FAAC operators from the late-1990s installations, plus BFT on newer commercial jobs. Most parts orders arrive within two business days, and we stock common capacitors, limit switches, and safety edges locally to avoid leaving your gate unsecured overnight. See all brands we service.
Pricing for Gate Repair in Irvington, NY
| Service | Typical Range in Irvington |
|---|---|
| Gate realignment (posts sound) | $180-$350 |
| Single hinge replacement (welded) | $180-$320 |
| Electric gate repair (capacitor, board, switch) | $220-$500 |
| Remote reprogramming or replacement | $150-$400 |
| Motor repair (capacitor, limit switch, tune) | $260-$620 |
| Custom welded piece (on-site fabrication) | $140-$380 |
| Rail repair (per section) | $240-$480 |
| Keypad entry repair or install | $350-$900 |
| Post replacement with new steel post | $550-$1,150 |
| Hinge and post repair (pillar rebuild) | $650-$1,200 |
| Single-leaf opener replacement | $1,100-$1,800 |
| Double-leaf opener replacement | $1,800-$2,800 |
What pushes price up in Irvington is almost always the masonry: brick pillars that need repointing, footings that have heaved and require resetting, or the tight access on narrow driveways that makes every step take longer. Every price is quoted and agreed before work starts. You’ll never get an invoice bigger than the quote.
Neighborhoods We Serve in Irvington
We’re out in Irvington neighborhoods every week. Typical response for a gate repair call is same day or next morning, and emergency calls about a gate stuck open get priority. We cover the full 07111 area.
- Irvington Center
- Stuyvesant Avenue corridor
- Chancellor Avenue area
- Union Avenue neighborhoods
- The Nye Avenue zone
Service Area - Cities Near Irvington
We work throughout Essex County and the surrounding towns with no trip charge inside the county. If you’re near Irvington, we also cover Greenburgh, NY, Dobbs Ferry, NY, Hartsdale, NY, Hastings-on-Hudson, NY, and Scarsdale, NY. Dispatch and scheduling are coordinated from our New York City office, but the crew that shows up at your gate knows these streets.
Serving Irvington, NY - Our Local Coverage Area
Gatewood Fence & Gate crews serve Irvington and the communities around it; dispatch is coordinated from our New York City office. The map shows the Irvington coverage area; if your address is on it, we can help.
Also serving nearby: Greenburgh, NY, Irvington, NY, Dobbs Ferry, NY, Hartsdale, NY, Hastings-on-Hudson, NY, Scarsdale, NY.
FAQs About Gate Repair in Irvington
Most Irvington calls are scheduled same day or the next morning, and for urgent security gates that won’t close, we treat the call as an emergency. A broken gate in Irvington means an unsecured driveway overnight, and we don’t make that wait. Call (877) 610-2993 and a live person will tell you when we can be there.
Gate repair typically doesn’t require a permit in Irvington, but new installation or structural changes to masonry pillars may need township approval, especially if the work faces a sidewalk or street. We check local requirements before starting any job that involves new footings or changes to the property line. If a permit is needed, we’ll tell you upfront and coordinate the paperwork.
We cover the entire 07111 ZIP code, including every neighborhood listed above and the blocks beyond. If your address is in Irvington, we’ll come to you with no trip charge inside the county. The standing offers apply everywhere we work: $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans.
Call (877) 610-2993 for a free estimate. A live person answers 24 hours a day, and Hal Gatewood stands behind every job with the 90-Day Done Right Promise in writing.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Irvington Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg