Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Eastchester, NY
Gate repair in Eastchester, NY typically runs $180-$340 for common issues like hinge rebuilds, operator adjustments, and post re-alignment, and most repairs are finished the same day we look at the gate. Eastchester is the kind of town where the gate at the end of the driveway isn’t just a decoration, it’s the first thing a commuter sees at 6:40 in the morning and the last thing they check before locking up at night. When it stops closing, you want somebody who knows the difference between a motor problem and a post problem on a 1960s colonial with original ironwork. That’s us. Call (877) 610-2993 and you’ll get a live person, not a recorded menu, and the person who answers will tell you when Hal can be there.
Why Eastchester Homes Are Different
Eastchester sits in the kind of Westchester County climate that eats a gate from the bottom up. We get 30 to 40 freeze-thaw cycles a winter, and every one of them works like a slow crowbar under a concrete footing. Frost heave tilts gate posts out of plumb a fraction of an inch a year, and that fraction changes the swing arc just enough to make the operator work harder every single day until the drive motor burns out. A homeowner sees a dead motor and calls for a new one, but if the post underneath moved half an inch, the new motor will burn out too. The real fix starts with re-plumbing and re-anchoring the post.
It doesn’t help that most of Eastchester’s housing stock went up in the 1940s through the 1960s. Those colonials and split-levels often have original or early-retrofit concrete gate post footings that have been shifting for six or seven decades. When we dig down, we find footings that were poured long before modern frost-depth codes existed. The original wrought iron is frequently still in place too, beautiful stuff that just needs the right hinge work rather than a trip to the scrapyard. And because Eastchester’s lots are compact and many gates sit within ten feet of a public sidewalk, post alignment isn’t just a mechanical issue, it’s a village code issue. A gate that drifts half an inch toward White Plains Road can end up swinging over the pedestrian zone.
Road salt is the other enemy here. The salt trucks on California Road and White Plains Road throw spray onto adjacent gate hardware all winter. Iron hinges corrode fast, and exposed low-voltage wiring on gate operators develops intermittent faults that drive homeowners crazy because the gate works fine one day and dead the next. We’ve learned to trace the whole circuit, not just the obvious break.
Gate Repair in Eastchester
Gate repair in Eastchester usually means one of three things: a swing gate that won’t swing, an operator that hums but doesn’t move, or a post that’s leaning toward the sidewalk. Most jobs run $220-$680 depending on what’s actually wrong, and we can usually have someone at your house the same day you call. Hal Gatewood has been fixing gates since 2001, and the person who answers the phone at (877) 610-2993 is the same person who’ll show up in your driveway, look at the gate, and tell you what’s really going on. Gate Repair is what we built this company on, and Eastchester’s mix of original ironwork and mid-century footings is exactly the kind of work we specialize in.
Electric Gate Repair
Electric gates in Eastchester put up with a lot: road salt spray on exposed wiring, freeze-thaw cycles that stress every connection, and intermittent faults that only show up when the temperature drops below 25 degrees. We trace the whole circuit, not just the obvious break, because in our experience the visible problem is usually downstream of the real one. Most electric gate repairs in Eastchester run $180-$420, including the trip inside the county.
Hinge and Post Repair
This is the work we do most often in Eastchester. A gate sags in the hinge post, not in the middle, and the posts on these 1940s to 1960s lots are often original concrete footings that have shifted out of plumb over decades of frost heave. Hal welds and rebuilds hinges on site, re-anchors posts, and gets the gate swinging on its original arc again. Repairs run $260-$680 depending on the damage, always quoted before we touch anything.
Gate Realignment
A gate that drags, binds, or won’t latch usually isn’t broken. It’s out of alignment. In Eastchester that misalignment is almost always caused by a post that moved, not a gate that bent. We re-plumb the post, reset the hinges, and adjust the operator’s travel limits so the gate closes on its own without straining. Realignment work starts around $220 and includes checking the safety sensors while we’re there.
Why does my Eastchester swing gate keep burning out its motor every winter?
Because your post is moving. Eastchester’s frost-susceptible soil goes through 30-40 freeze-thaw cycles each winter, and every cycle nudges the concrete footing a fraction of an inch. Once the post shifts even a half-inch, your gate’s swing arc changes, and the operator has to work harder every time it opens and closes. Eventually the drive motor overheats and dies. Replacing the motor without re-plumbing the post means you’ll replace the motor again next February. Call (877) 610-2993 and we’ll show you what’s actually happening underground.
Can you retrofit an old wrought-iron gate with modern safety photocells?
Yes, and we do it regularly in Eastchester. Most of the original wrought-iron gates on these 1940s-1960s lots predate UL 325 safety standards, so they have no photocells and no reversing edge. We can retrofit modern safety sensors and an auto-reverse function onto an old gate while preserving the original ironwork. It’s a repair-first approach that keeps your gate’s character and brings it into compliance. Estimates are free at (877) 610-2993.
Gate Installation in Eastchester
Gate installation in Eastchester, NY typically runs $2,800 to $9,500 for a complete automated driveway gate, with most swing-gate systems on Village streets landing between $3,500 and $5,800. We quote every job before work begins, in writing, and the number you see is the number you pay. If you’re off White Plains Road, near Lake Isle, or tucked into one of the side streets around Mill Road, we know the lots, the setback rules, and the mid-century footings you’re dealing with. Gate Installation is measured, ordered, and scheduled, never rushed, because a gate that isn’t measured against your actual post alignment will fail the first hard winter.
Swing Gate Installation
Swing gates are the majority of what we install in Eastchester, and for good reason. The mid-century colonials and Tudors here were built with ornamental ironwork in mind. But here’s the thing most installers miss: those original concrete footings were poured decades before modern frost-depth codes existed. Every winter, 30 to 40 freeze-thaw cycles heave those footings a measurable half-inch. We set new posts below the frost line, re-anchor properly, and then hang the gate. That’s the only way a swing gate survives a Westchester winter without burning out its operator.
Driveway Gate Installation
Eastchester driveways are compact by Westchester standards. Many sit just feet from public sidewalks, which means clearance tolerances matter more here than in towns with acreage. We measure for village-required setbacks before we order a single piece of steel. Whether you want ornamental aluminum to match your 1950s colonial or a solid privacy setup, we install it to swing true and clear the walk safely. A non-automated ornamental driveway gate runs $1,800 to $4,000 depending on width and material.
Sliding Gate Installation
Some Eastchester lots have driveways too steep or too short for a swing gate’s arc. That’s where sliding gates come in. They ride on a track, which means the track and the motor both need protection from road salt kicked up by Village plow trucks. We install slides with sealed bearing systems and elevated operator mounts so February doesn’t shut you down. Adding automation to a swing or slide gate brings the total to roughly $3,500 to $9,500, including the operator, safety edges, mounting, and electrical work.
Why does my Eastchester swing gate stop working every February, then recover in spring?
Frost heave is the culprit. Eastchester gets 30 to 40 freeze-thaw cycles each winter, and the original post footings on mid-century homes weren’t poured to modern frost-depth standards. The footing shifts a half-inch or so, the swing arc changes, and the operator overloads. When the ground thaws, the footing settles back just enough that the gate limps along again. The permanent fix is resetting the post below the frost line before installing any new operator. Call (877) 610-2993 for a free measure and written price.
Can you install a gate operator on my original 1950s wrought iron drive gate?
Usually yes, if the gate itself is structurally sound. The problem is rarely the iron; it’s the hinge post, the hinge barrels, and the footing. We’ve retrofitted operators onto original Eastchester wrought iron gates many times, but only after rebuilding the hinges and confirming the post is plumb and stable. If the post is heaving or the hinge pins are worn to half their thickness, adding an operator just burns it out. We’ll tell you honestly which category you’re in.
Gate Motor & Opener in Eastchester
When a gate motor fails in Eastchester, it usually isn’t the motor’s fault. That’s the first thing Hal Gatewood will tell you after twenty-nine years of fixing gates across Westchester County. In Eastchester, where automated wrought iron and aluminum swing gates sit on compact lots just feet from the sidewalk, a binding post or a shifted concrete footing overloads the operator until the drive motor burns out. We get to Eastchester quickly, diagnose what’s actually going on, and repair it right. Gate Motor & Opener service is what separates a one-season fix from a gate that runs for years.
Motor Repair
We repair gate motors more often than we replace them. A drive motor that’s humming but not moving, or a gate that opens halfway and reverses, usually points to something upstream: a misaligned post, a corroded limit switch, or a control board with water intrusion from a March nor’easter. Hal will open the motor, test the capacitor, the limit switches, and the circuit board, and tell you what actually needs replacing. Often it’s a $40 part, not a $900 motor. A typical gate motor repair in Eastchester runs $220 to $480, which includes diagnostics, labor for the repair, and the replacement part.
Motor Installation
New operators on Eastchester’s older swing gates require more than bolting a box to the post. The gate itself has to swing true. If the hinge post is out of plumb by even three degrees, a new motor will fight that resistance until it wears itself out early. That’s why our installations start with the gate, not the operator. We measure the gate’s weight, length, and swing arc, check the post alignment, and only then match the right motor to the load. New swing-gate operator installation runs $1,200 to $2,600 depending on gate weight and whether we’re building new posts or working with the existing ones.
Linear Motor Service
Linear arm operators are common on Eastchester swing gates, and they fail predictably when the gate’s swing arc changes. Frost heave from the 30 to 40 freeze-thaw cycles we get each winter tilts a post half an inch, and suddenly the arm has to push harder than it was specced for. The gears strip, or the internal limit switch rides past its mark. We keep Linear gears, limit cams, and control boards in our service stock, so a repair usually finishes the same day. Linear arm motor replacements typically land between $350 and $700 when the arm itself is serviceable.
How fast can you get to Eastchester for a gate motor repair?
We typically reach Eastchester within 45 to 90 minutes for emergency calls, depending on traffic on the Bronx River Parkway and the Cross County. We keep regular service days in southern Westchester, so non-emergency repairs are usually scheduled within one or two days. A live person answers the phone 24 hours a day, and Hal will give you a realistic window, not a vague promise. For a same-day repair quote, call (877) 610-2993.
What warranty do you offer on gate motor work in Eastchester?
Every job we do in Eastchester carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back to make it right. No runaround, no “it must have been something else.” We also honor manufacturer warranties on all new motors and parts we install. The promise is stamped on every invoice, not buried in fine print.
Gate Access Control in Eastchester
In Eastchester, a gate access system has to do more than open and close. It has to look right on a 1950s colonial, hold up through dozens of Westchester freeze-thaw cycles, and stay reliable when you’re rushing to catch a Metro-North train. Typical access control work in Eastchester runs $280-$1,150 depending on whether we’re rebuilding an existing keypad, adding a phone entry unit, or wiring a full card reader system into an older operator. We dispatch our Gate Access Control crew with the right parts for Eastchester’s salt-heavy, frost-heave conditions, not generic hardware that fails the first wet March.
Keypad Entry Systems
Keypads take the worst weather in Eastchester: snow, road salt mist from White Plains Road, direct sun on south-facing gate posts. We replace weather-warped membranes, re-seat corroded wiring terminals, and program new codes the same visit. Most keypad swaps or rebuilds in Eastchester run $280-$450 fully installed.
Phone Entry and Video Intercom
Older phone entry boxes on Eastchester’s split-levels and Tudors often date back to the original gate installation. Running new low-voltage wire from the gate to the kitchen line or adding a video intercom with a small standalone monitor is work we do without trenching your walkway. Expect $600-$1,150 for a full phone entry or video intercom install depending on wire run length and mounting conditions.
Remote Control and Receiver Upgrades
If one opener remote works and the other doesn’t, the problem is rarely the button in your hand. On homes near Lake Isle and the Post Road corridor, we regularly find deteriorated receivers or interference from newer LED security lighting on neighboring properties. We test signal strength, swap receivers, and re-sync all your remotes while we’re there. Remote receiver replacement runs $220-$380.
How do Eastchester prices compare to nearby towns like Scarsdale or Bronxville?
Our pricing is the same across all of southern Westchester, including Eastchester, Scarsdale, Bronxville, and Tuckahoe. We don’t mark up based on the zip code. Typical access control repairs in Eastchester run $280 to $450, and new installations run $600 to $1,150 depending on system type and wire condition. You’ll get a written quote before any work begins, and a free second opinion on any written estimate from another company.
What kind of warranty comes with gate access control work in Eastchester?
Every job we do carries the 90-Day Done Right Promise in writing. If the work isn’t done right, one call brings Hal back. That promise covers the labor and the parts we supplied. You don’t chase anyone down, and you don’t get told the original problem somehow wasn’t included. The name is on the shop, and the shop is down the road, that is the oldest accountability there is.
Gate Parts & Welding in Eastchester
Gate parts and welding in Eastchester usually means one of three things: a hinge that’s rotted through, a post that frost heave has pushed out of plumb, or an operator that’s burning out because the gate’s swing arc changed by half an inch. We handle all three, and we do the welding on site, in your driveway, so the gate never leaves your property. Gate Parts & Welding is where our repair-first philosophy shows most clearly: Hal would rather weld a new hinge on 50-year-old iron than sell you a gate you don’t need.
Hinge Replacement
On original wrought iron gates in Eastchester, the hinge is almost always the first thing to fail. Road salt from the compact street grid gets into the pin, the pin corrodes, and the gate starts to drag. We weld new hinges on site. We don’t swap the panel, we don’t sell you a new gate. A welded hinge on 50-year-old iron is stronger than the original and it looks right. Most hinge replacements on residential gates in Eastchester run $180-$380 per hinge, depending on the weight of the leaf.
Post Replacement
This is the one Eastchester homeowners never see coming. The post looks fine at the top, but down at ground level it’s rotted or the frost heave has tilted it. On these compact lots, a post that’s out of plumb by half an inch changes the gate’s swing arc enough to overload a motor every January. We excavate the old footing, bore a new hole below the frost line, set a new steel post, and weld the gate back to it. Post replacement in Eastchester typically runs $600-$1,400 including concrete work.
Rail Repair
A rusted bottom rail is common on old iron gates near Lake Isle and the streets that see heavy salt spread. The rail rots through, the gate sags on the hinge side, and the whole thing looks tired. We cut out the rusted section and weld in new solid steel rail stock. We can match the profile of the original iron close enough that you can’t tell where the repair starts. Rail repair generally runs $250-$600 depending on how much of the rail we’re replacing.
Why does my Eastchester swing gate keep burning out its operator every January?
Because the post is moving. Frost heave pushes your 1950s-era concrete footing up and over, even half an inch, and that changes the gate’s swing arc enough to overload the motor every time it cycles. On Eastchester lots the footing is often original and shallow, so winter is when it shows. The real fix is to excavate the old footing, bore below the frost line, and re-anchor the post. Replacing the operator without fixing the post is throwing good money away. Call (877) 610-2993 and we’ll show you what’s underground.
Can you weld a new hinge on my original wrought iron gate without replacing the whole panel?
Yes, and that’s usually the right approach. We cut off the old hinge, grind the area clean, and weld a new steel hinge barrel to the existing rail. The original panel stays. On Eastchester’s older ironwork, a welded hinge often outlasts the rest of the gate. Most hinge replacements run $180-$380 per hinge, including the weld work and the pin. We’ll quote it before we strike an arc.
Brands We Service in Eastchester
We stock parts and carry factory training for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. On most Eastchester repair calls, we finish the same day because the part is already on the truck. For specialized Linear, Viking, or Ghost Controls components we don’t have in stock, our New York City office coordinates overnight delivery so we’re back on your property within 24 hours. our brands
Pricing for Gate Repair in Eastchester, NY
| Service | Typical range in Eastchester |
|---|---|
| Basic electric gate repair (capacitor, limit switch) | $180-$320 |
| Electric gate repair (full diagnostic) | $180-$420 |
| Gate realignment | $220 |
| Hinge and post repair | $260-$680 |
| Hinge replacement (per hinge, welded) | $180-$380 |
| Rail repair and weld-in patch | $250-$600 |
| Post replacement with new footing | $600-$1,400 |
| Gate motor repair | $220-$480 |
| Linear arm motor replacement | $350-$700 |
| New swing-gate operator installation | $1,200-$2,600 |
| Slide-gate operator installation | $1,500-$3,100 |
| Keypad entry system | $280-$450 |
| Remote receiver replacement | $220-$380 |
| Phone entry / video intercom | $600-$1,150 |
| Custom bracket or latch fabrication | $120-$450 |
| Full swing-gate realignment with operator reset | $350-$800 |
What pushes price up in Eastchester is almost always post condition and wire condition. Original footings from the 1950s and 60s need deeper excavation than modern posts, and low-voltage wiring that has been exposed to road salt for decades often needs full replacement rather than a quick splice. The price we quote is the price you pay, period. No trip charge inside the county, and every quote is agreed in writing before any work starts.
Neighborhoods We Serve in Eastchester
We cover all of Eastchester, including the 10709 zip code, and we’re typically on site within a couple of hours for repair calls. Here’s a sample of the areas where you’ll see our truck regularly:
- Lake Isle area
- Garth Road corridor
- California Road neighborhood
- White Plains Road area
- Eastchester Town Hall district
If you don’t see your street listed, don’t read anything into it. If you’re in Eastchester, we come to you.
Service Area - Cities Near Eastchester
We work throughout southern Westchester County. If you’re near the border, you might be closer to one of our other regular stops. We also serve Tuckahoe, NY, Wykagyl, NY, Bronxville, NY, Scarsdale, NY, and New Rochelle, NY. Dispatch and scheduling are coordinated from our New York City office, but the crew that shows up at your gate knows these streets. Eastchester, NY remains our home base for this part of Westchester.
Serving Eastchester, NY - Our Local Coverage Area
Gatewood Fence & Gate crews serve Eastchester and the communities around it; dispatch is coordinated from our New York City office. The map shows the Eastchester coverage area; if your address is on it, we can help.
Also serving nearby: Eastchester, NY, Tuckahoe, NY, Wykagyl, NY, Bronxville, NY, Scarsdale, NY, New Rochelle, NY.
FAQs About Gate Repair in Eastchester
Most gate repairs don’t require a permit in Eastchester, but any new installation or structural modification to the gate post may need Village approval, especially if the gate swings within ten feet of a public sidewalk. We know the setback rules and can tell you during our free estimate whether your job triggers a permit. If it does, we’ll point you to the right Village office and document the work to their standard.
For emergency calls, we typically arrive within 45 to 90 minutes depending on parkway traffic. A live person answers the phone 24 hours a day, and we’ll give you a real arrival window, not a four-hour guess. Non-emergency repairs are usually scheduled within one to two days. Call (877) 610-2993 and we’ll tell you exactly where we are.
Yes. We work throughout Eastchester’s 10709 zip, including homes near Lake Isle, the streets off White Plains Road, the Garth Road corridor, and the neighborhoods bordering Tuckahoe. We’re familiar with local building codes and the common gate styles on Eastchester’s older housing stock. If your property is in Eastchester, you’re in our service area.
Call (877) 610-2993 for a free estimate. A live person will answer, and Hal will show up when he says he will. Every job carries the 90-Day Done Right Promise in writing, and the price we quote is the price you pay. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Eastchester Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath