Gate Repair in Tyrone - Same-Day Repair, Priced Before We Start

Gate Repair in Tyrone, GA

Gate repair in Tyrone, GA usually comes down to one thing: a gate that was installed when the house was built, somewhere between 1990 and 2008, and has finally given out. The original swing-gate operators those homes came with are now 15 to 30 years old, and they’re failing in a concentrated wave across the 30290 zip code. We fix the gate in your driveway, weld on site, and put the 90-Day Done Right Promise on every invoice. Call (877) 610-2993 and a live person picks up, any hour.

Call (877) 610-2993

Why Tyrone Homes Are Different

Tyrone’s residential buildout filled Fayette County’s large estate lots with upscale homes on half-acre to several-acre properties. Those homes came with heavy dual-swing gates, long-run slide gates, and brick-column entrances that were built to match the house, not ordered from a catalog. The gates themselves are ornamental iron, wide, and heavy. A light-duty operator from a home improvement store never had a chance out here.

Then there’s the climate. Fayette County’s winter ice storms coat gates in freezing rain rather than snow. That sudden weight strips gear assemblies and bends actuator arms on swing operators that were never fitted with slip clutches. Summer humidity gets to work on the wrought-iron hinges and pivot points the ice already stressed. What a homeowner sees is a gate that won’t open. What we see is years of accumulated damage from a climate that punishes metal in two directions.

The other Tyrone-specific factor is under the gate itself. Red Georgia clay swells and contracts with seasonal rainfall, and over a decade it shifts brick gate posts out of plumb. When a technician just replaces limit switches or the operator and calls it fixed, the gate will be out of alignment again inside a year. The real fix is re-setting the post footer. We check the column with a level before we touch the motor, because in Tyrone the post is where the problem starts.

Gate Repair in Tyrone

Most gate repairs in Tyrone run between $180 and $550, and the most common job we do out here is replacing or retrofitting the original operator that came with the house. The homes off Tyrone Road and Palmetto Road built in the 1990s and 2000s often came with Apollo, LiftMaster, or Viking automated gates, and those units are failing now, decade by decade. We stock parts for those brands, repair what can be repaired, and tell you straight when a replacement makes more sense than a patch.

We handle the full range of Gate Repair work in Tyrone, from a gate that won’t open to one that scrapes the driveway every cycle. Hal runs the jobs himself, and the person who shows up is the person whose name is on the invoice.

Electric Gate Repair

Most of the electric gates in Tyrone were installed when the house was built, and that was often between 1995 and 2008. The operator that came with the house has outlived its warranty by a decade. We repair what can be repaired, and when the board or motor is truly done, we replace the operator with something sized for the specific gate, not just whatever’s on the shelf.

Electric gate operator replacement, which is the most common job we do in Tyrone because of the 1990s and 2000s buildout, runs $600 to $1,800 installed depending on brand and gate weight. Every price is quoted in writing before we start.

Automatic Gate Repair

Automatic gates on large-lot Tyrone properties are usually dual-swing or long-run slide systems. These require commercial-grade operators, even on a home. We carry boards, arms, and gear assemblies for the brands most common in this area, including Viking, DoorKing, and Elite.

A hinge and post repair on an ornamental iron gate typically lands between $250 and $475, depending on whether the footer needs to be re-set or just re-shimmed. Simple labor calls like realigning a gate that drags start around $150.

Hinge & Post Repair

A gate sags in the hinge post, not in the middle. That’s the first thing we check. In Tyrone, the red clay under your brick columns is constantly working against you, and a post that’s drifted half an inch makes the gate bind and the operator strain. We re-set footers, rebuild hinge mounts, and weld cracked hinge barrels on site.

Fix the panel without the post and you’ll fix it twice. We quote the full job before any work starts, and the number on the written estimate is the number you pay.

Can you repair a gate the same day in Tyrone?

For most hinge, realignment, and operator troubleshooting calls, yes. Jobs that need parts we don’t have on the truck usually get finished the next day, because we stock for the brands most common in Tyrone. If your original 2002 LiftMaster is dead, we’ll likely quote you a replacement the same day and schedule the swap quickly. Call (877) 610-2993 and we’ll tell you honestly when we can be there.

Do you cover all Tyrone neighborhoods and the 30290 zip code?

Yes, we cover the entire 30290 zip code, including the older estate sections off Senoia Road, the neighborhoods around Sandy Creek Road, and the larger properties toward Palmetto Road. There’s no trip charge inside Fayette County, and Tyrone is fully inside that coverage area.

Gate Installation in Tyrone

If you need a new driveway gate in Tyrone, you’re probably dealing with one of two things: an original operator from the early 2000s that’s finally given out, or a gate that’s sagged because the clay soil underneath shifted the posts. Either way, you want someone who understands Tyrone’s properties, not a franchise that’s never seen red Georgia clay. We size every Gate Installation to the actual gate weight and driveway width, and we quote the full price up front.

Driveway Gate Installation

Most driveways in Tyrone run long, and the properties sit on half-acre to several-acre lots. A light-duty kit from a big box store won’t hold up. A double swing gate across a 16-foot drive needs a commercial-grade operator, even at a residence.

A single swing driveway gate, steel or aluminum, typically lands between $2,400 and $5,200, including operator and safety edges. Double swing gates across a wide drive start around $5,500 and can reach $12,000 or more for ornamental iron with matched columns.

Sliding Gate Installation

For properties where the driveway slopes toward the house or where swing gates would eat up too much apron space, a slide gate is the better answer. Tyrone’s long-run slide gates sit on concrete aprons that heave with the freeze-thaw cycle. We pour and level the track base with that movement in mind, and we check the rack and pinion alignment twice before we call it done.

Sliding gate installations run $4,800 to $9,500 depending on track length and operator class.

Pedestrian Gate Installation

A walk gate at the side of the house or along the fence line still needs a proper footer. In Tyrone’s clay soil, we dig deeper than the minimum and set the post in concrete. That’s the difference between a gate that latches clean for fifteen years and one that binds in eighteen months. A new pedestrian walk gate with a basic latch runs $600 to $1,400.

Why do so many gate operators in Tyrone need replacement at the same time?

Tyrone’s residential buildout peaked between 1990 and 2008, when automated driveway gates became standard on the estate lots here. Those original Apollo, LiftMaster, and Viking operators are now 15 to 30 years old and hitting the end of their service life all at once. If your gate is original to the house, a retrofit control board or full operator replacement is probably the fix, not a whole new gate.

How does Tyrone’s red clay affect a new gate installation?

The clay under your gate posts expands with rain and contracts in dry months, and over enough years that movement shifts brick columns out of plumb. A proper gate installation in Tyrone starts with checking the post footings and often re-setting them with poured concrete before hanging the gate. Skip that step and you’ll get a gate that binds within a season or two, no matter how good the hardware.

Gate Motor & Opener in Tyrone

A failing gate motor in Tyrone usually gives you warning signs before it quits entirely: a grinding sound on the track, a gate that starts then stops, or an opener that hums but won’t move the gate. Most repairs in the 30290 area run between $180 and $340 for parts and labor, and we can usually have your gate working again the same day we look at it. We service nine major brands, including Viking, DoorKing, and Elite, and we stock parts for the operators most common in Tyrone’s original buildout.

For full Gate Motor & Opener work, from board swaps to complete operator replacement, we diagnose in the driveway, show you exactly what’s failed, and hand you a written quote before we turn a wrench.

Motor Installation

When a LiftMaster or Viking unit finally dies, we don’t patch it with a band-aid. We spec the right commercial-grade replacement for your gate’s weight and length, mount it correctly, and set the travel limits so it doesn’t fight itself on every cycle.

A full motor installation on a typical Tyrone driveway gate runs $850 to $2,200 depending on whether it’s a single swing, dual swing, or slide configuration.

Motor Repair

Most motor repairs in Tyrone are control-board failures, stripped gear assemblies, or limit switches that drifted out of adjustment. Fayette County’s freezing rain events are particularly hard on gear assemblies, because ice adds sudden weight to the gate leaf and the motor takes the strain. Common repair jobs run $180 to $480. If the repair exceeds $200, you get $40 off. That’s a standing offer, not a negotiation.

Slide Motor

A long-run slide gate on a two-acre Tyrone lot needs a heavy operator, and when the motor starts to strain on the rack gear, you’ll hear it before you see it. The real culprit on slide gates in this area is often the concrete pad shifting over time with Fayette County’s clay soil, which throws the chain alignment off just enough to overload the motor. Slide motor replacement runs $850 to $1,800 depending on the run length and operator class.

Can you handle a gate that won’t close after a winter ice storm?

Yes, and this is one of the most common calls we get in Tyrone. Freezing rain adds weight that strips gears and bends actuator arms, especially on older swing operators without slip clutches. We’ll diagnose the damage, quote a repair, and in most cases have the gate operating the same day. Call (877) 610-2993 and mention the ice event when you call.

What kind of warranty do you give on gate motor work in Tyrone?

Every job we do carries the 90-Day Done Right Promise in writing. If the same problem comes back within 90 days, one call brings Hal back to make it right, no charge and no runaround. That goes for installations, repairs, and parts we supply.

Gate Access Control in Tyrone

Gate access control in Tyrone usually means one of six things: a keypad that’s gone dead, a remote that stopped triggering the opener, a phone entry system that won’t buzz the gate open, a card reader that’s intermittent, a video intercom that’s dropped offline, or a smart access setup that never quite worked right after a power surge. Most jobs run $240 to $680 for the repair itself, and we can usually have someone at your driveway the same day you call.

We work on all of it as part of our Gate Access Control service, and we test the whole path, not just the box at the gate. That matters in Tyrone, where long driveway runs and older wiring corrode connections in ways a quick swap won’t fix.

Keypad Entry

A keypad that types but won’t open the gate, a keypad with buttons that only work when it’s warm out, a keypad that flashes but never fires: in Tyrone, these symptoms show up constantly on systems wired through long driveway runs. The fix is often a corroded connection or a failing relay, not necessarily a new keypad.

Keypad replacement or repair runs $180 to $420 depending on the keypad and whether we’re re-pulling wire to it.

Phone Entry

Phone entry systems on Tyrone estate gates tend to fail at the house side: the relay that answers the call, the phone line itself, or the DTMF decoder that’s supposed to hear the “9” and fire the opener. Phone entry system repair runs $240 to $580, and we quote the specific relay, decoder board, or line-interface work before we start.

Remote Control

Remotes that work 10 feet from the gate but not 40, remotes that eat batteries, remotes that only trigger the gate when the car is pointed a certain way, these are the everyday calls we run in the 30290 area. Sometimes it’s the remote. More often it’s the receiver antenna, the control board input, or a frequency issue on an older LiftMaster.

Remote reprogramming or receiver replacement runs $95 to $280. Reprogramming a working receiver is the low end; a new receiver and antenna is the high end.

Do you handle emergency access control failures in Tyrone?

Yes, and we answer the phone 24/7 with a live person. A keypad that dies on a Friday evening leaves you either locked out or holding the gate open all weekend. Call (877) 610-2993, tell Hal what the system is doing, and he’ll tell you whether it can wait until morning or whether someone should head your way now.

Does your warranty apply to access control work in Tyrone?

Every job, including keypad, remote, phone entry, card reader, video intercom, and smart access work, carries the 90-Day Done Right Promise. If it isn’t done right, Hal comes back and makes it right, no runaround. That’s a written promise on every invoice, and it applies to every home in Tyrone the same way it does everywhere else we work.

Gate Parts & Welding in Tyrone

Gate parts and welding in Tyrone usually comes down to one of three things: a hinge that has finally worn through, a post the red clay has pushed out of plumb, or an operator from the 1990s that quit mid-cycle on a long private driveway. We fix all three on site, and we weld in your driveway rather than hauling the gate to some shop across the county.

Our Gate Parts & Welding work means the gate stays in your driveway. Hal welds on site, matches the profile of the original ironwork, and primes and paints the repair so it disappears into the rest of the gate.

Hinge Replacement

On Tyrone’s ornamental iron gates, the hinge is where clay movement and humidity get together to do damage. A half-acre lot five or ten years past its last hinge job will show a gate sagging toward the latch side, dragging on the driveway, and stressing the operator arm every single cycle. A sealed-bearing hinge replacement on a standard ornamental iron gate typically runs $220 to $480 per hinge, depending on gate weight and whether we’re welding a reinforced plate.

Post Replacement

Brick gate posts in Tyrone sit in red Georgia clay that swells after spring rain and shrinks in August. Over a decade, that cycle quietly shifts the post out of plumb. You see it as a gate that won’t line up with the latch or an operator that trips its obstruction sensor for no obvious reason. Post re-setting with a new concrete footing usually falls between $450 and $900 per post.

Custom Welding

Some Tyrone homeowners have gates that were fabricated to match the house, not ordered from a distributor. When a decorative scroll breaks or a hinge plate tears off the frame, you need someone who can weld to the original design, not swap in a part that looks close. Custom welding repairs, like matching a broken scroll or re-welding a torn hinge plate, run $180 to $600 for most residential ironwork.

Can you straighten a brick gate post that has leaned over a decade, or does it need full replacement?

In most Tyrone cases, yes, the post can be salvaged. The lean comes from clay movement at the footing, not from the column itself failing. We excavate the old footer, reset the post on a new concrete pier, and weld any reinforcement before re-hanging the gate. Full replacement is only needed when the brick column itself has cracked through or the rebar has rusted beyond structural value.

Do you match custom gate welding to the original ornamental design on older Tyrone homes?

Yes. We weld on site and match the profile of the original ornamental ironwork, including leaf patterns, scrolls, and frame pipe dimensions. The repair gets primed and painted, not left as a raw weld. That matters on Tyrone’s estate homes where the gate was fabricated to match the house. Call (877) 610-2993 with a photo and we’ll tell you what’s involved.

Brands We Service in Tyrone

We service the gate brands most common in Tyrone’s original 1990s and 2000s buildout, including Viking, Ghost Controls, DoorKing, and Elite. We stock boards, arms, gear assemblies, and receivers for those units locally, which keeps most repairs to a same-day or next-day turnaround instead of waiting on a distributor. See our brands for the full list of what we work on.

Pricing for Gate Repair in Tyrone, GA

Neighborhoods We Serve in Tyrone

We cover all of Tyrone, zip code 30290, with typical response times measured in hours, not days. Our Fayette County crew is usually already working within 20 minutes of your neighborhood when you call. You’ll see our trucks regularly in:

• River Oaks
• Lakeside at Tyrone
• Estates of Tyrone
• Briarwood
• Homes along Senoia Road and Tyrone Road

Service Area - Cities Near Tyrone

We serve Tyrone, GA and the surrounding Fayette County and south metro communities. Our crews also work regularly in Fairburn, GA, Fayetteville, GA, Union City, GA, Riverdale, GA, and College Park, GA. Dispatch and scheduling are coordinated from our Atlanta office; the crews serving Tyrone live and work in this part of the county.

FAQs About Gate Repair in Tyrone