Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Stallings
Gate installation in Stallings runs about $2,800 to $9,500 for a full driveway or HOA entrance system, depending on whether you’re replacing a failed builder-grade operator or putting a new slide gate in from scratch. Most single-family driveway gates in the 28079 zip land in the $3,500 to $6,500 range, while community entrance gates with automation and safety edges run higher. Call (877) 610-2993 and we’ll give you a straight number before any work starts.
We know Stallings not as a dot on a map but as the town we drive through on our way to HOA entrances off Chestnut Lane, Pleasant Plains Road, and the neighborhoods branching from Stallings Road. The subdivisions here went up fast in the early 2000s, and a lot of the gate hardware did too. We show up when we say we will, and the person who answers the phone is the same person whose name is on the invoice.
Why Gatewood Fence & Gate Is Stallings’s Preferred Gate Installation Company
Hal Gatewood has been owner-operating this shop since 2001. That means when you call about gate installation in Stallings, you’re talking to someone who knows what a Linear swing operator from 2005 sounds like when the capacitor starts to go. You’re not getting shuffled through a menu. You’re getting the person who will be standing in your driveway with a welder and a level.
Stallings homeowners and HOA board members keep our number for one reason: we fix what’s there before we sell you something new. If a hinge post is out of plumb, we brace it and weld it true rather than quoting a whole new gate. That repair-first habit has built our reputation across Union County over more than two decades. The 90-Day Done Right Promise is on every invoice in writing. If it’s not right, one call brings us back.
Response time to Stallings from our Charlotte office is typically same day for gate failures that leave an entrance inoperable, and next morning for installations that need measuring and ordering. A live person answers 24 hours a day. Not a voicemail. Not a chatbot. Hal’s cell number isn’t a secret.
Our Gate Installation Services in Stallings
Sliding Gate Installation
Sliding gates are the workhorse of Stallings HOA entrances because they don’t swing into traffic and they handle the gentle slopes common along Pleasant Plains Road. We install cantilever and V-track slide systems sized to the opening, including concrete pad work for the operator post and steel rack welded level. When we replace a slide gate in Stallings, we check the original post footings because Union County clay moves more than the builder who poured them planned for. A gate that binds six months after install was usually set on a footing we would have deemed too shallow.
Swing Gate Installation
Swing gates are the standard for brick-front driveway entrances in the newer subdivisions off Stallings Road. We install single and double swing configurations with hinge posts set below frost and braced against seasonal clay swell. If the gate will be automated, we insist on proper thrust bearings and reinforced posts. A gate sags in the hinge post, not in the middle, and that is where the work starts.
Double Gate Installation
Double gates are two leaves that meet in the middle, and every double gate we install in Stallings gets a paired operator setup or a heavy-duty single operator with a slave arm, depending on width. The common failure we see on older double gates in 28079 is one side drifting out of alignment as the clay under one post settles faster than the other. We set both posts on a shared footer with welded brackets during installation so they move together, or not at all.
Pedestrian Gate Installation
A separate pedestrian gate keeps people from wearing out your big driveway gate. In Stallings, where nearly every subdivision off Zebulon Road or Mill Grove Road includes community walking paths, HOA boards often ask us to install a pedestrian gate alongside an existing automated entrance. These are smaller, lighter, and can be matched to the ornamental aluminum style already on the property. We install them with self-closing hinges and, when requested, keypad or card-reader access.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Stallings
We’re factory-certified to service and install nine major gate brands, and for Stallings jobs we most often work with FAAC, BFT, Linear, and LiftMaster. That matters because a lot of the HOA entrances here were built with mid-2000s Linear or LiftMaster operators that are now past their rated service cycles. We keep common control boards, limit switches, and actuator arms on hand so an install or replacement in Stallings doesn’t stall waiting for a part to ship from somewhere else. If you’re replacing an old Viking or Elite unit, we’ll match the mounting to avoid re-drilling concrete unless the footing itself needs rework.
Common Gate Installation Problems We See in Stallings Homes
- Builder-grade operators failing on a schedule. The operators installed during Stallings’s 2000-2015 subdivision boom were often the cheapest unit that met code. Fifteen to twenty years later, the control boards are corroding and the motors are burning out at roughly the same time. We replace them with heavier-duty units built to run cycles measured in decades, not election cycles.
- Clay soil racking hinge posts out of plumb. Union County’s expansive Piedmont clay absorbs water and swells in winter, then contracts in summer. Over years, that seasonal movement pushes gate posts off vertical. A gate that scrapes or binds is usually a footing problem, and we correct the post before we hang anything new on it.
- Adding automation to a gate that was installed manual. A lot of Stallings driveways have perfectly good ornamental gates that were never set up for automation. The posts are often fine, but there’s no power run and no operator mount. We retrofit these every month, trenching conduit and installing a transformer with proper depth and weather protection.
- Ice storm damage to aluminum pickets and actuator arms. The Piedmont gets ice, not snow, and a quarter inch of ice on an aluminum gate adds hundreds of pounds. We see sheared actuator arms and cracked pickets after a single bad freeze. Full gate replacement or reinforcement is sometimes cheaper than chasing cracks every winter.
Pricing for Gate Installation in Stallings, NC
Here are real numbers for the Stallings market, not national averages that mean nothing, and every price is agreed in writing before we start.
- Pedestrian gate installed: $900-$2,200
- Single swing driveway gate with new posts: $3,200-$6,500
- Automatic slide gate for HOA entrance: $5,500-$9,500
- Adding automation and safety sensors to existing gate: $2,800-$5,200
What moves the price is post footing depth, gate material thickness, whether we’re correcting an existing out-of-plumb post, and the operator brand you choose. A FAAC or BFT unit costs more than an entry-level Linear but runs cleaner and lasts longer. We quote the job before any metal is cut. Call (877) 610-2993 for an exact number. Estimates are free, and if you have a written estimate from another company, we’ll give it a second look at no charge.
We Also Serve Cities Near Stallings
Our Gate Installation team works throughout Union County and the east side of the Charlotte metro. If you’re in Stallings or just over the line in Indian Trail, Wesley Chapel, Matthews, or Mint Hill, the same crew and the same 90-Day Done Right Promise apply.
Serving Stallings, NC - Our Local Coverage Area
We’re based in the Stallings area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Stallings
Yes, in most cases the existing gate leaf can be converted if the hinge posts are still plumb and structurally sound. We trench a power run from the nearest exterior-rated circuit, install a rated operator with UL 325 compliant safety edges and photocells, and add whatever access control you want, whether that’s a simple keypad or an HOA gate with remote fobs. The gate itself usually stays put. Call (877) 610-2993 and we’ll tell you if your specific gate is a candidate.
Because they were all installed around the same time by the same Charlotte-area developers using the same mid-2000s operators and weld-on hinge hardware. When one community gate off Chestnut Lane starts faulting, we usually hear from two more within a month. The control boards were never rated for 20 years of humid-summer oxidation and ice-storm cold cycles, and now they’re all reaching the end together.
For swing gates, choose an articulated arm operator with a soft-stop feature rather than a linear piston. The articulated arm tolerates the slight post movement that clay swell causes. For slide gates, either a pad-mount motor with drive chain or a rack-and-pinion system on a properly over-engineered concrete footer. We always dig the footer below the shrink-swell zone so the operator post doesn’t heave in winter.
For a vehicle gate, yes on the loop detector. A loop detector or photo-eye setup is what stops the gate from closing on a car, and modern UL 325 standards require entrapment protection on any automated gate. Keypad entry is optional but standard for gated driveway installs in Stallings because most homeowners want access for delivery drivers and family without handing out remotes. We install free-exit loops and safety edges on every automated system.
Usually, if you have enough lateral space along the fence line for the gate to slide open. In Stallings, many 2000s-era subdivision lots have the side setback to convert a swing gate to a slide gate without touching the existing fence panels. We install a steel V-track or cantilever system, move the operator post, and reuse or extend the existing fence sections as needed. The old swing hinge posts are either removed or cut flush and capped, then we weld the new gate to match the existing ornamental style. Call (877) 610-2993 and we’ll measure it free.
Call Gatewood Fence & Gate for Gate Installation in Stallings
If your gate is sagging, the operator is throwing fault codes, or you’re ready to put a real gate and opener where a cheap one has been for 20 years, call (877) 610-2993. Hal Gatewood will answer, or he’ll call you back within minutes. This is the same number we’ve had for years, and the same person shows up who looked at your gate the first time. A gate installation in Stallings should be done by someone who knows the soil, the weather, and the builder-grade shortcuts we keep having to undo. That’s us.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Stallings and surrounding Union County communities since 2001.