Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Roxborough Park
Gate installation in Roxborough Park means dealing with wide openings, long gravel drives, 60 mph Chinook winds, and an HOA that actually checks what you build. We know because we’ve set gates along Roxborough Drive, off Rampart Range Road, and up against the hogback where the sun disappears by mid-afternoon in December. A new driveway gate here starts around $2,800 and a solar-powered operator on a 16-foot double swing gate typically runs $6,800 to $9,400 installed. If you’re looking at a gate across a wide agricultural opening or a long western-facing driveway, call us at (877) 610-2993 and Hal will talk through what makes sense for your property. We’re the local gate company that welds on site and stands behind the work with a 90-Day Done Right Promise, in writing, on every job.
Why Gatewood Fence & Gate Is Roxborough Park’s Preferred Gate Installation Company
Hal Gatewood has been running this company since 2001, and the name is still on the shop. That matters when you’re spending six or ten thousand dollars on a gate that has to survive wind, deer, and an HOA review. We publish our address and license number. If something isn’t right, you can drive to the shop and look Hal in the eye. That’s the oldest accountability there is, and it’s why homeowners in Roxborough Park call us before the national outfits.
Our Gate Installation team has set gates on custom foothill homes from the late 1980s through the 2000s for over two decades now. The difference shows in what we check before we quote: post footings under 6×6 cedar that has been racking for 25 years, north-facing solar panel orientation against the hogback shadow line, and HOA finish standards that a flatland installer from Littleton would never think to ask about. We answer our own phone 24/7, and when you call, a live person picks up. Not a voicemail tree, not someone three states away.
Our Gate Installation Services in Roxborough Park
Driveway Gate
A driveway gate in Roxborough Park is rarely a simple swap. The average driveway here is a quarter-mile of gravel off Roxborough Drive or Waterton Road, and the gate at the end of it is the first thing the HOA sees. We install swinging and sliding driveway gates built from wrought iron and cedar to match the existing custom home styles, and we handle the full operator mount, safety edges, and access control so the gate actually works for the next twenty years, not the next two.
Double Gate
A 12-foot or 16-foot double swing gate across a wide entrance takes two posts set in 36-inch footings, a matched pair of operators if you want automation, and alignment hardware that can take mule deer shoulder hits without throwing the photocell path off. We set a 16-foot double gate for a property at the end of a quarter-mile gravel drive off Roxborough Drive, pairing a LiftMaster LA500 dual swing operator with a 20-watt solar kit because running conduit would have meant trenching through 220 feet of decomposed granite and mature scrub oak. The existing hinge posts were 6×6 cedar set in 1997, so we pulled them and set 8×8 pressure-treated posts in 36-inch footings after finding both racked a full two inches out of plumb from repeated 65 mph wind events. That’s the standard we hold.
Swing Gate
Swing gates look simpler and cost less upfront, but a 12-foot cedar swing gate at 6,000 feet acts like a sail in a Chinook. The wind load goes straight into the hinge post, not the panel, and that’s where cheap installs fail. We size post footings for the actual wind exposure on your side of the hogback, not a generic chart. Then we match the gate material and finish to the HOA’s approved palette so you don’t get a correction notice two weeks after the pour cure.
Sliding Gate
For openings over 20 feet or driveways with a steep grade right at the road, a sliding gate is usually the right call. You need a proper steel track or cantilever beam, enough setback for the gate to fully retract, and a motor with the torque to move a heavy iron gate in winter. We install sliding gates with FAAC and BFT operators, and we stock the parts locally so a repair call to Roxborough Park doesn’t wait on a parts truck from Texas.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Roxborough Park
We install and service FAAC, BFT, Linear, LiftMaster, and Viking operators, and when we put a motor on a gate in Roxborough Park, we size it for the altitude and the winter sun angle. A 20-watt solar panel that works fine in Highlands Ranch will brown out here between November and February unless the battery bank is oversized. We account for that on day one, not when you’re standing outside in a snow squall wondering why the gate won’t open. If you already have an operator from another brand, bring us the model number and we’ll tell you whether it’s worth repairing or replacing. Honest answer, no upsell.
Common Gate Installation Problems We See in Roxborough Park Homes
- Hinge post failure from Chinook wind racking. A 12-foot cedar swing gate in 60-plus mph downslope gusts loads the post footing, not the panel. The gate sags, the latch misses, and someone slams it harder until the post shears or the hinges pull loose. We set deeper posts from the start because we know what the wind does up here.
- Solar operator brownouts in winter. Panels on north-facing posts near the hogback shade lines produce almost nothing from November to February. If the battery bank wasn’t oversized, the low-voltage lockout leaves the gate stuck closed at 7 a.m. on a workday. We size panels and batteries for the shortest day of the year, not the average.
- Deer shoulder-check damage on double gates. Mule deer moving between Roxborough State Park corridors push against the center gap of wide double swing gates, bending alignment brackets and throwing off the safety photocell path. The operator refuses to close, and the homeowner assumes the motor failed. It didn’t. The gate got shoved.
- HOA compliance flags on material and finish. Roxborough Park’s design standards require gates to match the natural red-rock aesthetic. A non-compliant swap or a finish that doesn’t match the approved palette triggers HOA review and a correction order. We handle the finish and material spec before you buy, so you don’t end up repainting or replacing a gate the board rejects.
Pricing for Gate Installation in Roxborough Park, CO
Here are honest numbers for this market, based on what we’ve quoted and built around Roxborough Park in the past few years. A single swing gate with post replacement and hardware runs $2,200 to $3,600. A standard 12-foot driveway gate with a solar operator and safety edges runs $5,500 to $7,800. A 16-foot double swing gate with dual operators, matched panels, and HOA-compliant finish runs $6,800 to $9,400. A sliding gate setup with a track, cantilever hardware, and operator starts around $7,500 for a 20-foot opening. What moves the number: post condition, run of electrical conduit if you skip solar, gate weight, and whether we’re pulling old posts out of 25-year-old granite-hard backfill. The price we quote is the price you pay, agreed before we start. No door knock markup. Standing offers apply: $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside Douglas County, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote on your gate. Estimates are free.
We Also Serve Cities Near Roxborough Park
We set and service gates across the foothills and the flatland suburbs that ring Roxborough Park, including Littleton, Highlands Ranch, Columbine, and Ken Caryl. If you’re on acreage near Roxborough State Park or in a newer subdivision just down the road, the same crew and the same 90-Day Done Right Promise apply. Learn more about our work across the region on our Gate Installation in Roxborough Park page.
Serving Roxborough Park, CO - Our Local Coverage Area
We’re based in the Roxborough Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Roxborough Park
Yes. Roxborough Park is a private master-planned community, and the HOA design standards require gates to conform to approved materials, finishes, and styles that reflect the natural red-rock aesthetic. Wrought iron and cedar/redwood are the dominant approved materials. A simple swap-out with a non-compliant finish is a code violation that triggers HOA review, so we spec material and finish against the current standards before you buy anything. Call (877) 610-2993 and we’ll walk your lot and tell you what will pass review.
For a 20-foot opening, yes, a sliding gate is almost always the right call. A swing gate that wide needs massive posts, takes a huge wind load, and eats driveway space when it arcs open. A sliding gate with a steel track or cantilever beam handles the width cleanly and holds up to wind and deer better. We’ll measure the setback and grade on your lot off Roxborough Park Road and tell you which track system fits. Estimates are free at (877) 610-2993.
Yes, if it’s sized correctly for the short days and the shade lines. A 20-watt panel on a north-facing post near the hogback will brown out between November and February unless the battery bank is oversized. We size for the shortest day of the year, not the annual average, and we orient panels south where the lot allows. If your gate sits in a shaded draw, we may recommend a larger panel, a bigger battery bank, or a hardwired feed. Call us and we’ll check your sun exposure before quoting.
Build the gate with deer-rated alignment hardware and a center gap that doesn’t invite pushing. Mule deer moving between Roxborough State Park corridors will shoulder-check a double gate at the center gap, bending the alignment brackets and knocking the safety photocell path out of line. We install heavy-duty center stops, reinforced brackets, and photocell mounts positioned out of the impact zone. It costs a little more upfront and saves you repeated service calls every spring. Call (877) 610-2993 to talk through the spec.
In most cases we can re-weld it on site, and that’s our first recommendation. We carry welding gear on the truck, and Hal has been welding iron and steel gates since 2001. If the frame is cracked at the hinge mount, the fix is often a gusset plate and a proper weld, not a whole new gate. We’ll tell you honestly whether the frame has life left or whether the metal is too fatigued to hold. The second opinion is free, and so is the drive inside Douglas County.
Get Your Roxborough Park Gate Installed Right
When you’re ready to talk about a gate across your driveway or the wide opening off Roxborough Park Road, call (877) 610-2993. A live person answers 24/7. We’ll come measure, check your posts and sun exposure, and give you a written price before any work starts. Ninety days after we leave, if it isn’t done right, one call brings Hal back. No runaround, no fine print. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Roxborough Park and the surrounding foothills since 2001.