Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Richland Hills, TX
If your gate drags across the driveway or won’t latch after a North Texas rain, you’re dealing with the most common repair call in Richland Hills: a post that’s shifted in the black clay. Gatewood Fence & Gate fixes that in one visit, usually the same day you call. Hal Gatewood started this shop in 2001 and still answers the phone himself. When you call (877) 610-2993, you’ll get a real person who knows this ZIP code and can tell you what’s wrong before we even pull up.
Why Richland Hills Homes Are Different
Richland Hills is one of the smallest incorporated cities in Texas, roughly 1.7 square miles, and nearly every home is a post-WWII ranch built between 1950 and 1975. That matters because the gate posts were set decades ago, before anyone fully understood what Tarrant County’s Blackland clay does over time. The clay swells when it rains and shrinks when it dries, and every wet-dry cycle nudges a post a little further out of plumb.
The result is what we see across virtually every block in 76180: gates that were hung straight in 1965 now lean toward the house, drag on the concrete, and refuse to latch. North Texas summers top 100 degrees and warp wooden gate frames. Ice storms crack dried-out cedar. But the chronic problem is under the ground. The post heaves, the hinges stress, the frame torques. Tightening hardware without re-plumbing and re-setting the post just brings you back within one rainy season. Show me the gate closing on its own and I’ll show you where it’s failing.
Gate Repair in Richland Hills
Gate repair in Richland Hills usually comes down to one of three things: a hinge post that has heaved out of plumb in the Blackland clay, a worn operator that no longer reverses on obstruction, or a wooden frame that Texas weather has finally gotten to. Most calls we run in the 76180 ZIP are on homes built between 1950 and 1975, with gates that were hung decades after the house went up. That means we’re almost always working on aging infrastructure that needs more than a quick adjustment.
Our Gate Repair team handles everything from post resets to full control board replacements, and every job carries our 90-Day Done Right Promise in writing.
Hinge & Post Repair
This is the dominant repair call in Richland Hills, and the reason is under your feet. Tarrant County’s expansive black clay shrinks and swells with every wet-dry cycle. Posts set in the 1960s and 70s, often without concrete or with shallow footings, heave out of plumb. Tightening the hinges won’t fix a post that has moved. We dig down, re-set the post in new concrete below the clay line, and re-hang the gate so it actually swings square. A typical hinge and post repair runs $225 to $450 depending on the size of the post and whether it needs a new concrete footing. Fix the panel without the post and you’ll fix it twice.
Gate Realignment
A gate sags in the hinge post, not in the middle, and that is where we start. In Richland Hills, where original wooden swing gates are now 20 to 40-plus years old, we see sagging that gets blamed on the gate itself when the real culprit is a leaning post or a stretched hinge. We bring the gate back to level, adjust the latch so it catches cleanly, and set the reveal so it doesn’t bind on the post in summer heat. Gate realignment typically runs $150 to $300.
Electric & Automatic Gate Repair
Electric gate repair in Richland Hills often involves operators that predate current UL 325 safety requirements. We rebuild what can be rebuilt, replace what can’t, and make sure the safety photocells and obstruction reverse actually work. A gate operator that won’t stop when a child or a dog crosses the path is a serious hazard. Electric gate repair starts around $180 for limit switch and wiring fixes and goes up to $600 to $1,200 when a control board or motor replacement is involved. A full operator swap on a single-leaf gate usually lands between $800 and $1,500 installed. We fix the post, then the operator, because fixing one without the other means you’ll call us again next spring.
Why do so many gates in Richland Hills lean even after the hinges are tightened?
Because the hinge post has heaved out of plumb in the expansive Blackland clay, and no amount of hinge tightening corrects a post that has moved. Richland Hills sits on shrink-swell clay that shifts with every wet-dry cycle. The only lasting fix is to re-set the post in new concrete at a depth below the clay line, then re-hang the gate on the now-square post. Call (877) 610-2993 and we’ll check it with a level before touching a wrench.
My 1990s automatic gate opener still runs but the gate won’t reverse on obstruction. Is that repairable in Richland Hills?
Yes, if the control board or photocell pair can be sourced or rebuilt. Many 1990s operators have obsolete boards that are no longer manufactured, but some can be replaced with aftermarket boards that restore obstruction reverse. The safety issue is urgent: a gate that won’t reverse on obstruction can injure a child or pet. We’ll assess the operator, check the photocells, and give you a straight answer on whether a repair or replacement makes more sense.
Gate Installation in Richland Hills
Gate installation in Richland Hills is a different job than it is a mile south. The ground here moves. If you’ve lived in the 76180 for more than one wet season, you already know what Blackland clay does to a post set in concrete. A new driveway gate in this ZIP code usually runs $1,400 to $4,800 installed, depending on whether it’s a single swing panel or a full double security gate with an opener. The price matters less than how deep the posts go, because shallow posts in this clay mean a second install within two years.
Our Gate Installation team measures, welds, and hangs every gate on site.
Driveway & Swing Gate Installation
Most Richland Hills homes were built between 1950 and 1975, and the driveway openings reflect that era: narrower than new builds, with older concrete approaches. That affects gate placement. We account for vehicle swing radius, opener arm geometry, and where the post will sit relative to existing drive strips. A single steel driveway gate for a modest ranch-home opening typically starts around $1,800 here. Double swing gates on wider driveways get matched posts set with extra depth, because the clay will try to move them out of plumb within a year if you cut corners. We don’t cut corners.
Pedestrian & Sliding Gate Installation
Along the 6-foot cedar fences that run through Richland Hills backyards, the pedestrian gate is the piece that gets opened twice a day and ignored the rest of the year. We install walk gates with proper corner bracing and stay wheels where the ground is uneven, which it usually is in this clay. A well-built pedestrian gate in Richland Hills should last 15 years, but only if the hinge post goes deep enough. We go deep. For driveways with a slope or tight turnaround, a sliding gate often beats a swing gate. Sliding gates typically run $2,200 to $4,500 depending on track length and whether a motor goes in.
How fast can you install a gate in Richland Hills?
Most gate installations in Richland Hills are scheduled within five to seven business days, sometimes sooner when weather cooperates. Because we weld on site and stock parts locally, we don’t wait on a warehouse in another state. Call (877) 610-2993 and Hal will give you a straight window, not a four-hour guess.
Do you handle gates on the older ranch homes in Richland Hills?
Constantly. The post-WWII ranch stock that makes up most of Richland Hills has original gate and fence infrastructure that’s now 40 to 70 years old. We’re used to working around mature trees, narrow side yards, and older concrete approaches that new-construction crews won’t touch. That’s most of what we do.
Gate Motor & Opener in Richland Hills
If your gate motor has quit in Richland Hills, the fix usually lands somewhere between $180 and $520 depending on whether we’re replacing a control board or swapping the whole operator. Most repair calls in the 76180 ZIP are handled same-day because we keep common parts stocked locally, not ordered from a warehouse two states over. Hal Gatewood has been working on gates since 2001, and when he says someone will show up, it’s a real person who knows the difference between a Linear slide motor and a Viking swing arm.
Our Gate Motor & Opener service covers repair, replacement, and new installation on nine major brands.
Motor Repair & Installation
This is where Hal gets almost evangelical. A surprising number of dead motors in Richland Hills are fine except for a failed capacitor, a corroded limit switch, or a gearbox someone never greased. Repair is usually $180 to $520, and we’ll tell you plainly if the motor isn’t worth saving. Throwing away a $900 operator because a $40 part failed is the kind of waste that bothers us. When a motor truly can’t be saved, we install a new one sized to your gate’s weight and the post’s condition. A fresh motor on a wooden ranch-style gate in Richland Hills typically runs $650 to $1,400 installed, depending on brand and whether we need to add a mounting plate or re-shim the post.
Linear & Slide Motor Service
Linear operators are common on the sliding driveway gates you’ll see along the wider lots off Rufe Snow Drive and Baker Boulevard. These motors use a toothed rail and drive gear, and when the rail gets caked with dried mud and oak pollen, the gear chatters and strips. A typical linear motor repair in Richland Hills runs $220 to $600. A full linear operator replacement, including rail and brackets, lands between $900 and $1,800. Slide gates in 76180 tend to be on the few parcels with enough frontage for them, often on corner lots in the older sections of town. These operators work hard in summer heat, and the wheels and track take abuse from the same clay that heaves everything else. We’ll tell you if the real problem is the track itself, because putting a new motor on a binding track gets you six months of life instead of fifteen years.
How fast can you get to Richland Hills for a gate motor repair?
Most non-emergency repairs in Richland Hills are scheduled same-day when you call before midday, and emergency calls are handled around the clock. A live person answers the phone 24/7, so you’ll know your window before you hang up. Call (877) 610-2993 for a specific time today.
Does your gate motor work in Richland Hills come with a warranty?
Every job carries our 90-Day Done Right Promise in writing. If the work isn’t done right, one call brings us back to make it right, no fine print and no runaround. That goes for motor repairs, installations, and the post work we do alongside them.
Gate Access Control in Richland Hills
When your gate keypad won’t accept the code or the phone entry box goes silent, you don’t have time for a gate company that treats Richland Hills like a far corner of the map. A dead access control system means you’re either climbing out to key in codes manually or leaving the driveway unsecured. We get calls about this every week from homes along Baker Boulevard, Rufe Snow Drive, and the neighborhoods west of St. John’s Church, and we know the access control wiring in this ZIP code has been through decades of lawn equipment, heat cycles, and amateur splices.
Our Gate Access Control team programs, repairs, and installs keypads, remotes, phone entry, and card readers.
Keypad & Remote Service
The classic drive-up keypad is still the most common access method we service on Richland Hills gates, and the North Texas summer is its worst enemy. Triple-digit heat bakes those plastic housings until the membranes crack, and years of sun exposure on west-facing driveways tends to fade the numbers until nobody can read them. We replace failed keypads, rewire poorly spliced connections, and program new codes on the spot. Most keypad swaps on a Richland Hills driveway run $180 to $320 including the new unit and programming. If your opener remote works only when you’re standing five feet from the gate, or you have to click three times to get a response, the issue is often a receiver antenna that got knocked loose or a control board that’s losing its range. Remote or receiver service lands around $120 to $260.
Phone Entry & Card Reader Installation
Phone entry systems let a visitor press a call button at the gate and reach your cell phone, which is a practical setup for Richland Hills households with long driveways or a gate set back from the house. These systems depend on good cellular signal, and we will tell you plainly whether your location works before you spend money on the hardware. A phone entry install in Richland Hills usually runs $400 to $800. For homeowners who just want to tap a card or fob and roll through, a card reader system is a durable, low-fuss option that holds up better in Texas heat than keypads. A single-family card reader setup in Richland Hills is typically $350 to $650 installed.
How fast can you get to my Richland Hills home for a gate access control problem?
For access control failures that lock you out of your driveway, we can typically get someone to Richland Hills the same day you call. The city is barely 1.7 square miles, so our nearest crew is never far away, and because dispatch and scheduling run from our Dallas-Fort Worth office, we keep Richland Hills calls close to the top of the morning board. Call (877) 610-2993 and we will give you a real arrival window.
Are your prices higher in Richland Hills than in nearby cities?
No. Our pricing is based on the work, not the city line. A keypad replacement costs the same in Richland Hills, North Richland Hills, or Watauga: generally $180 to $320. We don’t add a surcharge for a Richland Hills address, and there is no trip charge inside the county. The price is quoted and agreed before any work starts.
Gate Parts & Welding in Richland Hills
If you live in Richland Hills and your gate sags, drags, or won’t stay latched, there’s a good chance the problem isn’t the gate panel itself. It’s the hinge post heaving in that stubborn Blackland clay. We’ve been fixing exactly this across the 76180 ZIP code long enough to know the soil here does more damage than any storm. We come to you with a welding machine, a post-hole digger, and the parts that actually fit a 40-year-old gate frame.
Our Gate Parts & Welding service covers hinges, posts, rails, and custom fabrication on site.
Hinge & Post Replacement
Gate hinges in Richland Hills take a beating from the Blackland clay shifting underneath them. A gate that scrapes the ground on one corner usually has a bent or seized hinge, not a warped panel. We stock heavy-duty hinges rated for the weight of solid cedar gates, and we weld or bolt them on so they stay put through wet-dry cycles. A standard hinge replacement runs $140 to $280, depending on hinge weight and whether we weld or bolt. If the hinge post itself is leaning, we address that too, because a new hinge on a heaving post is wasted money. Post replacement is the big one: figure $380 to $900 for a single wooden gate post set with new concrete and bracing.
Rail Repair & Custom Welding
Rails crack, rot, and pull loose from hinges over time. On older ranch homes around Richland Hills, we frequently see top rails rotted from the inside while the pickets still look fine. We can weld steel rails onto existing frames or replace wooden rails and re-secure every picket. Rail repairs land between $180 and $450. Some jobs need a fabricated bracket, a reinforced hinge mount, or a completely custom steel gate frame. We bring the welding rig to your driveway and handle it on site. Custom welding jobs start around $150 for a simple bracket or hinge reinforcement and go up from there. That matters in Richland Hills, where a 60-year-old driveway post may not sit square with anything made in a factory.
Can you weld a gate on site in Richland Hills, or does it need to go to a shop?
We weld on site, in your driveway, in your yard, wherever the gate lives. That’s the whole point of our service. Hauling a gate to a shop adds a day you don’t get back and risks warping it in transit. We bring the welder, the generator, and the know-how to Richland Hills and fix it where it stands.
What warranty do I get on gate parts and welding in Richland Hills?
Every job carries our 90-Day Done Right Promise in writing. If a weld fails or a hinge sags within 90 days, we come back and make it right at no charge. No forms, no hassle. Just call the same number you called the first time. Richland Hills is small, and word travels. That’s why we answer the phone, show up when we say we will, and fix the gate instead of talking you into a new one.
Brands We Service in Richland Hills
We stock parts and carry certifications for nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common failures on Viking and Linear operators can be fixed with what’s on the truck today, not ordered next week. See all brands we service.
Pricing for Gate Repair in Richland Hills, TX
| Service | Typical Range in Richland Hills |
|---|---|
| Hinge & post repair | $225 - $450 |
| Gate realignment | $150 - $300 |
| Electric gate repair (wiring/limit switch) | $180+ |
| Control board or motor replacement | $600 - $1,200 |
| Full operator swap (single-leaf) | $800 - $1,500 |
| Single driveway swing gate (new) | $1,400 - $2,800 |
| Double driveway gate (new) | $2,800 - $4,800 |
| Sliding gate (new, with track) | $2,200 - $4,500 |
| Motor repair | $180 - $520 |
| New motor installation | $650 - $1,400 |
| Keypad replacement | $180 - $320 |
| Post replacement with concrete | $380 - $900 |
What pushes price up in Richland Hills is almost always the soil work: posts heaved in Blackland clay need deeper footings and more concrete than a gate hung on stable ground. Every price is quoted and agreed before any work starts, in writing, so the number we give you is the number you pay. No surprises at the door.
Neighborhoods We Serve in Richland Hills
We work in every corner of Richland Hills, from the ranch homes along Baker Boulevard to the streets near Richland High School and the Richland Recreation Center. Our typical response time for the 76180 area is same-day for most gate repair calls.
- Baker Boulevard corridor
- Rufe Snow Drive area
- Near Richland Elementary
- Near Richland High School
- Richland Tennis Center area
Service Area - Cities Near Richland Hills
Gatewood Fence & Gate serves Richland Hills, TX and the surrounding communities from our Dallas-Fort Worth office. We also work in North Richland Hills, TX, Watauga, TX, Hurst, TX, Haltom City, TX, and Bedford, TX. No trip charge applies inside the county.
Serving Richland Hills, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Richland Hills and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Richland Hills coverage area; if your address is on it, we can help.
Also serving nearby: Richland Hills, TX, North Richland Hills, TX, Watauga, TX, Hurst, TX, Haltom City, TX, Bedford, TX.
FAQs About Gate Repair in Richland Hills
Most gate repairs in Richland Hills don’t require a permit, but new installations or changes to the fence line may need approval from the city. We can tell you whether your specific job triggers a permit requirement when we look at it, and we’ll help with the paperwork if it does. Call (877) 610-2993 and we’ll walk you through it.
A live person answers our phone 24 hours a day, and most repair calls in the 76180 ZIP are scheduled same-day when you call before midday. Because Richland Hills is only 1.7 square miles, our crew is never far from any address in the city. Emergency calls are handled around the clock.
Our 90-Day Done Right Promise covers any failure of the gate, posts, hardware, or opener that results from our workmanship. If a post heaves within that window, we fix it at no charge. After that, a properly set post in Richland Hills clay should stay put for years, because we set it deep and in the right amount of concrete from day one.
Call (877) 610-2993 today for a free estimate on any gate repair, installation, or welding job in Richland Hills. Hal answers the phone himself, and he’ll tell you straight whether you need us now or whether it can wait.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Richland Hills Customers Say
"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth