Gate Repair in Plano - Same-Day Repair, Priced Before We Start

Gate Repair in Plano, TX

Gate repair in Plano usually comes down to one of three things: a sagging ornamental iron gate that won’t latch, an operator that hums but won’t move, or an HOA notice taped to your front door. We handle all three, and we’re in Plano neighborhoods every week. Call (877) 610-2993 and a live person picks up, day or night.

Call (877) 610-2993

Why Plano Homes Are Different

Plano sits on the Blackland Prairie, and the black clay under your gate does something the sandier soil west of here doesn’t: it heaves. After a wet spring and a dry August, the ground shifts enough to tilt a hinge post a few degrees. A gate that pinned perfectly in March suddenly scrapes the driveway in September. We see this every season in Plano.

On top of that, Plano’s residential boom left two very different gate populations. East Plano’s 75074 and 75075 neighborhoods have operators from the late 1980s and 1990s that are failing in clusters: control boards dying, capacitors bulging, underground loop detectors shorting out. West Plano’s 75093 has larger lots, heavier decorative iron panels, and high-torque commercial-grade operators on six-figure estate gates. The east side needs electrical and mechanical repair. The west side needs precision fabrication and HOA-spec work, especially around the Legacy corridor in 75024 where architectural review committees watch every repair.

Gate Repair in Plano

Gate repair in Plano runs from about $175 for a basic limit switch or photo eye up to $950 for custom fabrication on a west-side estate gate where HOA review and powder-coat matching are required. The spread is real because the jobs are real: a shifted hinge post on east-side clay, a dead 1990s control board in a 75074 subdivision, or a twisted ornamental panel that an HOA committee in 75093 says must match the original exactly. We quote the price before any work starts, in writing, and that price doesn’t change when we show up.

Electric Gate Repair

Electric gate repair in Plano covers control boards, capacitor failures, dead receivers, and shorted transformers. In east Plano ZIPs like 75074 and 75075, a lot of the original 1990s operators are dying in clusters right now because they were all installed in the same building boom. Boards fail, capacitors dry out, and loop detectors quit sensing. We stock common boards for LiftMaster, FAAC, Viking, and DoorKing, so on most calls we complete the Gate Repair the same day we diagnose it. A control board swap on a commercial-grade operator typically lands between $350 and $600 installed.

Automatic Gate Repair

Automatic gate repair in Plano usually splits into two categories: slide gates with ground tracks and swing gates with arm operators. The slide gates here grind and bind because Blackland Prairie clay shifts the track base, especially between wet spring and dry August. The swing gates fail more often at the operator arm or the limit switches. We work on Ghost Controls, Elite, Mighty Mule, and the rest. If your gate opens halfway and stops, that’s a limit switch or a photo eye failure, not a mystery, and electric or automatic gate repair ranges from $175 to $600 depending on what failed.

Hinge & Post Repair

This is the one Plano homeowners ignore until the gate starts dragging concrete. The clay under Plano swells when it rains and shrinks when it dries. That cycle, year after year, tilts posts, cracks footings, and pulls hinge alignment out of plane. A gate sags in the hinge post, not in the middle, and that’s where we start. Hinge and post repair on a standard ornamental iron swing gate runs $275 to $500 depending on footing depth and whether we pour new concrete.

Gate Realignment

If your ornamental iron gate in Plano has a wider gap at the top latch than at the bottom hinge, the post has moved. We see it constantly on the west side, especially in neighborhoods off Legacy and along Tennyson Parkway where the custom estate gates are heavy, single-piece iron panels. Gate realignment alone typically runs $150 to $350. HOA architectural committees in 75093 and 75024 watch those gates closely, and realignment done wrong leaves weld marks and mismatched angles. Done right, you can’t tell we were there except the gate closes cleanly again.

Why do gate posts in Plano shift so much, and how does that affect my gate?

Gate posts in Plano shift because the Blackland Prairie clay under most of the city expands when wet and contracts when dry. That seasonal heave tilts posts, cracks the concrete footing, and throws the hinge line out of plane. You’ll notice the gate dragging at the bottom latch or leaving a wider gap at the top. The repair starts with the post, not the panel. Call (877) 610-2993 for an exact diagnosis, estimates are free.

My Plano HOA requires architectural review for gate repairs. How do you handle that?

We handle HOA-driven gate repair in Plano by matching your existing gate exactly. If you’re in a west Plano HOA in 75093 or near the Legacy district in 75024, your committee typically requires any replacement panel to match the original powder-coat color and picket profile. We source custom fabrication rather than stock panels and document the work so you can submit it for approval. Call (877) 610-2993 and we’ll walk you through what your committee will ask for.

Gate Installation in Plano

Gate installation in Plano usually costs between $3,800 and $14,500 for a complete driveway gate with operator, depending on whether it’s a lightweight aluminum pedestrian gate or a heavy ornamental iron double swing on concrete footings. The bigger variable isn’t the gate itself, it’s the approval process. Most Plano neighborhoods sit under an HOA, and west Plano especially has architectural review committees that want to see materials, finish colors, and picket profiles before a single post hole gets dug.

Driveway Gate Installation

This is the most common job we do in Plano, and it’s also the one where HOA friction shows up most. A typical driveway gate installation runs $4,200 to $14,500, covering everything from a single aluminum swing gate with a basic operator to a dual iron gate with custom fabrication, safety photocells, and a keypad entry. In west Plano’s 75093, where lots are larger and gates are heavier, plan toward the upper end of that range. We coordinate custom fabrication so the first submittal passes.

Pedestrian Gate Installation

Pedestrian gates in Plano run $900 to $3,600 installed, depending on width, material, and whether you want a matching operator or mechanical keypad. These smaller gates still need architectural approval if they’re visible from the street, and we pull together the finish sample and spec sheet your HOA will ask for. We rarely see a pedestrian gate get denied when the color and profile match the driveway gate. For a full Gate Installation, we handle everything from the first measure to the final inspection.

Swing Gate Installation

Swing gates are the dominant style in Plano’s HOA neighborhoods, especially the double swing gates on estates in Willow Bend and along Legacy Drive. A swing gate installation runs $3,800 to $13,000 in Plano. The cost depends heavily on post footings. Blackland Prairie clay moves, and a swing gate that’s heavy to begin with will lean if the footings aren’t poured deep and wide enough. We over-dig as a rule.

Sliding Gate Installation

Sliding gates make good sense on Plano lots where the driveway slopes toward the street or where a swing arc would hit landscaping. Expect to pay $4,500 to $12,500 for a sliding gate installation in Plano, including the track, rollers, motor, and safety edges. HOA boards in 75024 and 75093 tend to accept sliding gates when they match the fence line and use the same finish color. We handle the full power run and safety edge wiring so everything is code-compliant before inspection.

Does a gate installation in a Plano HOA community require architectural review before work begins?

Yes, nearly always. If you live in a Plano HOA neighborhood, especially in 75093 or 75024, you’ll need to submit a request to your architectural review committee before any work starts. That includes gate material, dimensions, finish color with a physical powder-coat sample if requested, picket profile, operator model, and a site plan showing post placement. Call (877) 610-2993 and we’ll prepare the submittal with you.

My east Plano home has an original 1990s gate operator that finally died. Can I replace just the operator?

In most cases, yes. East Plano homes in 75074 and 75075 often have perfectly good gates still standing, but the 25-to-35-year-old control boards and loop detectors are done. We’ll check the gate’s condition, and if the panel and posts are salvageable, we’ll swap the operator, loop detector, and safety photocells without touching the gate. Call (877) 610-2993 for a free on-site assessment.

Gate Motor & Opener in Plano

A gate motor or opener in Plano typically costs $450 to $1,800 to replace, depending on whether you have a light residential swing gate in east Plano or a heavy ornamental iron driveway gate in west Plano’s estate neighborhoods. Most repairs run $180 to $520 and we can usually get your gate working same day. If your gate won’t open or the opener is grinding, call (877) 610-2993 and Hal will talk you through what’s actually wrong before anyone drives out.

Motor Installation

A new gate motor installation in Plano runs $950 to $2,600 depending on gate weight, panel length, and whether you need a buried loop detector or a photo eye system. In west Plano’s master-planned communities, we regularly install high-torque commercial-grade operators on ornamental iron estate gates that weigh 900 pounds or more. Those jobs are measured, ordered, and scheduled. You get a free measure and a written price up front, and that price is agreed before any work starts.

Motor Repair

Most opener repairs in Plano come down to control boards, capacitors, limit switches, or a gearbox that’s been grinding through North Texas heat for twenty summers. We fix it in your driveway. We don’t haul the gate off to a shop and we don’t quote you a full replacement when a $140 part will do the job. Hal’s repair-first approach is why a lot of Plano HOAs and property managers keep our number saved. For full Gate Motor & Opener service, basic residential opener repair runs $180 to $400.

Slide Motor Repair

Slide gate motors get a workout in Plano’s hotter months. The steel track expands in August, the rollers bind, and the motor strains against a gate that’s fighting it every inch. We see a lot of slide motor failures in the 75023 and 75024 area, especially on back-alley access points and small commercial properties around Legacy. A heavy-duty slide motor replacement runs $1,500 to $2,800. We check track alignment and roller wear first, because a new slide motor bolted onto a worn track will burn itself out in under a year.

How fast can you get to my gate in Plano?

Same-day in most cases. If your gate is stuck open or won’t close at all, call us in the morning and we can usually have someone out to your Plano property before the afternoon. Emergency calls where a gate is stuck open get priority. Call (877) 610-2993 and you’ll talk to a live person who can give you a real arrival window.

Do you cover all Plano ZIP codes?

Yes. We work across all Plano ZIP codes, including 75093, 75094, 75023, and 75024, and we cover the neighborhoods off Custer Road, Independence Parkway, Preston Road, and Legacy Drive. West Plano estate gates, east Plano 1990s subdivisions, and the Legacy business district all get the same response. Call (877) 610-2993 and we’ll tell you when we can be there.

Gate Access Control in Plano

Gate access control in Plano means updating the way you open your driveway gate from inside the car, at the front door, or from your phone. Most Plano homes we visit need a new keypad, a phone entry system, or a card reader added to an existing gate operator, and the work usually takes a couple of hours once we’re on site. We know Plano’s HOAs and how its clay soil fights your gate posts.

Keypad Entry

A keypad at the driveway lets you punch in a code instead of hunting for a remote. This is the access control upgrade we install most often in Plano, especially in the older subdivisions around 75074 and 75075 where original operators never had one. A basic keypad install with existing wiring typically runs $240 to $380. We mount the keypad, wire it to your existing operator, and walk you through setting your own codes before we leave. For a full Gate Access Control upgrade, we’ll spec the right system for your setup.

Phone Entry

A phone entry system lets a visitor call your cell phone from the gate and you buzz them in. That’s useful in Plano’s gated communities, especially in newer west Plano developments in 75093 where guests and delivery drivers expect a call box at the street. A new standalone phone entry system usually lands between $450 and $800 depending on the wiring run from the house to the gate. We install standalone units and integrate them with existing DoorKing or Viking operators.

Card Reader

Card readers make sense for small HOA communities, ranch-style properties, and anyone who doesn’t want to hand out a code that changes hands too often. We install proximity card readers that work with a fob or a card, typically $300 to $550 per reader, and we can add them to most automated driveway gates in Plano. If you’re near the Legacy business district in 75024 and need controlled access for a shared entry, we can help you sort out what fits the existing operator rather than selling you a full replacement.

Can you come today for a dead keypad or gate that won’t open?

In most cases, yes. If you’re in Plano and your gate access control has failed completely, call (877) 610-2993 and we’ll give you a straight answer on timing. We stock common keypad, remote, and control board parts for Plano homes, so many failures get fixed on the first visit rather than after a part gets ordered.

Is gate access control cheaper in Plano than in nearby cities?

Pricing is essentially the same across Plano, Lucas, Allen, Murphy, and Sachse because the labor, parts, and trip are the same. The cost differences come from the job itself, not the city. A keypad on an existing operator runs $240 to $380 in Plano, and we don’t charge a trip fee anywhere inside the county. Call (877) 610-2993 for an exact quote.

Gate Parts & Welding in Plano

Gate parts and welding in Plano usually means one of three things: a hinge post has shifted out of plumb, a builder-grade opener has burned through a control board, or an HOA wants a repair to match the original ironwork exactly. We handle all three, and we do the welding on-site in your driveway so the gate never leaves your property.

Hinge Replacement

Most hinge failures in Plano start in the post, not the barrel. When the black clay under a gate post expands and contracts, the post tilts a few degrees, and that puts the hinge under load it was never designed to carry. A hinge replacement on a standard single swing gate typically runs $180 to $340, including the new hardware and on-site welding. We replace the hinge and re-align the post together, because fixing one without the other is how you get a repeat call.

Post Replacement

Post replacement in Plano is a Clay 101 course. The Blackland Prairie soil under this city is expansive clay, and it moves more in a single wet-dry cycle than most soils move in five years. Post replacement runs $450 to $950 depending on post size, footing depth, and whether we’re matching a custom powder-coat finish. When we set a new post, we dig deeper than the original, pour a footing that resists rotation, and weld the hinge mounts true. For full Gate Parts & Welding work, this is where a lot of repairs start.

Rail Repair

Slide gates in east Plano, particularly in 75074 and 75075, sit on clay that shifts enough to throw the rail out of alignment. When a rack and pinion slide gate binds mid-track, the drive gear eats itself. Rail repair and reweld work usually falls between $150 and $400. We weld cracked rails, straighten bent sections, and re-anchor the track to the slab. Where the slab has cracked, we address the footing first, because welding a rail to a moving slab just moves the problem six inches down.

Custom Welding

Custom welding is the default in Plano, not the exception. When an HOA in 75093 requires a replacement panel to match picket profiles from a 1998 build, you can’t order that from a catalog. Custom welding runs $95 to $150 per hour of fab time plus materials. We fabricate to match scrollwork, spear tops, ring handles, and custom latch brackets. We’ve matched powder-coat colors on-site more times than we can count, because HOAs here don’t accept close enough.

My Plano HOA needs the replacement hinge post to match the original powder-coat color. Can you match it?

Yes. We field-match powder coat colors on-site, and we document the RAL or manufacturer color code so the HOA’s architectural review committee has exactly what it needs. We’ve done this for HOAs across 75093 and 75024, and we know what documentation they ask for before the repair. Call (877) 610-2993 and we’ll walk you through the approval step by step.

My 1990s east Plano gate operator still works but the loop detector is failing. Is it worth replacing just that part?

In most cases, yes. A failing loop detector on a 1990s-era operator in 75074 or 75075 is a common end-of-life part, and replacing it often costs $200 to $400, far less than a full operator replacement. If the rest of the operator checks out, we’ll replace just the detector and you keep the unit for years. We won’t sell you a whole new opener because one part quit.

Brands We Service in Plano

We service and stock parts for the operators Plano homes actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Common boards and capacitors for Viking, Ghost Controls, and DoorKing stay on the truck, which means most repairs get done same day. See our brands for the full list.

Pricing for Gate Repair in Plano, TX

Neighborhoods We Serve in Plano

We work across all of Plano, but we spend a lot of time in these neighborhoods. Typical response time in Plano is same-day for emergency repairs and within 24 to 48 hours for scheduled work.

• Willow Bend (75093)
• Kings Ridge (75093)
• Legacy area near Preston and Legacy Drive (75024)
• Harrington Park and Davis Library area (75074)
• Buckingham and Custer Road corridor (75075)

Service Area - Cities Near Plano

We serve Plano and the surrounding Collin County cities with the same crews and the same 90-Day Done Right Promise. That includes Lucas, TX, Allen, TX, Murphy, TX, Sachse, TX, and Addison, TX. If you’re in one of these cities, the phone number is the same and the live person answering it is the same.

FAQs About Gate Repair in Plano