Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Fast, Reliable Gate Installation Across Parkchester
Gate installation in Parkchester means something different than anywhere else in the Bronx. You’re not calling about a driveway on a side street. You’re calling about a courtyard gate that’s part of a 129-acre co-op complex built by MetLife between 1938 and 1942, and the person on the other end of the line needs to understand that. We do. A new gate in Parkchester typically runs $2,800 to $11,000 depending on the span, the operator, and whether the post footings need resetting. Call (877) 610-2993 and you’ll reach a live person who knows exactly what co-op board approval means and how to work through it.
We’re Gatewood Fence & Gate. Hal Gatewood’s name is on the shop, and he’s been at this since 2001. We work in Parkchester every week, and we know the buildings, the parking facilities, and the facilities managers who run them. You don’t need a gate company that treats 10462 like every other zip code. You need someone who has pulled a work order for a courtyard on Metropolitan Avenue and knows how the process actually goes.
Why Gatewood Fence & Gate Is Parkchester’s Preferred Gate Installation Company
When a gate fails in Parkchester, it fails on shared infrastructure. That’s not a small detail. The co-op board wants to know who’s coming onto the property, what the gate will look like, whether the work will hold up against the next winter’s freeze-thaw cycle, and whether the contractor will still be around in six months if something shifts. Hal has been answering yes to those questions for over two decades. He welds on site. He doesn’t haul your gate to some shop across town. The gate stays in your courtyard or parking lot, and the person who quoted the job is the person doing the job.
We’ve installed gates in Parkchester’s courtyards, rebuilt ornamental iron from the original MetLife era, and replaced barrier arms in the flat parking lots where ice heave racks everything out of alignment by March. We show up when we say we will. The 90-Day Done Right Promise comes in writing on every job. If it’s not right, one call brings Hal back. No runaround. We also answer the phone 24/7, and I mean a person, not a voicemail tree.
- Locally owned and owner-operated since 2001 – Hal Gatewood’s name is on the shop and on every invoice.
- 90-Day Done Right Promise in writing – if it’s not done right, we make it right.
- On-site welding – your gate stays in Parkchester, fixed where it stands.
- Live person answers every call, 24/7 – no dispatch queue, no chatbot.
- Upfront pricing with standing offers – $40 off any repair over $200, free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans.
We serve the entire Parkchester complex, including the courtyards off Metropolitan Oval, the parking facilities near White Plains Road, and the building entries throughout 10462. When a facilities manager calls us about a gate that’s sagging in a hinge post, we come out, look at it, and tell you straight whether that post needs resetting or whether the gate itself is done. No upsell. No swapping parts that don’t need swapping.
Our Gate Installation Services in Parkchester
Here’s what we actually install in Parkchester, and what each one looks like on this property.
Sliding Gate Installation
Most of the parking facility gates in Parkchester are sliding gates, and they take a beating. The large flat lots pool water at the gate bases, and when that water freezes, it heaves the track. We install sliding gates on a properly reset post footing, not just bolted to whatever was there before, so they track smoothly through the worst of a Bronx winter. We also stock replacement rollers and track sections locally for Gate Parts & Welding in Parkchester, which means we’re not waiting on a freight truck when a gate binds mid-February.

Swing Gate Installation
Swing gates in Parkchester usually hang on posts set into original MetLife-era masonry. That masonry is over 80 years old, and the anchor points at ground level are often corroded. We cut out the old footing, set a new post base into the concrete, and build up from there. A swing gate on a fresh post swings true and stays that way. A swing gate on a failing post sags again by the next season, and you’ll pay twice.

Double Gate Installation
Double gates are common on the wider vehicle entries in Parkchester’s parking lots. Two leaves mean twice the hardware, and the leaves have to meet cleanly at the center stop. We set both posts, hang both leaves, and adjust the center alignment so the gate latches without slamming. When a double gate gets out of sync, it’s almost always the post, not the leaf.

Pedestrian Gate Installation
Pedestrian gates serve the courtyard entries and building access points throughout Parkchester. These are the gates people actually touch every day, so the hardware matters. We install self-closing hinges, proper latching systems, and keypad or intercom entry where the co-op board wants Parkchester Gate Access Control. We also fabricate replacement panels to match the original ornamental iron, which matters in a complex that still carries its 1938 MetLife aesthetic.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Parkchester
We’re certified to work on a full range of gate operators and hardware, including FAAC, BFT, Linear, Viking, LiftMaster, DoorKing, Ghost Controls, Elite, and Mighty Mule. For Parkchester’s parking facilities, we regularly recommend FAAC underground operators for swing gates where surface space is tight, and BFT for sliding gates on long runs. The underground FAAC units survive the freeze-thaw cycles far better than surface-mount alternatives because the operator housing sits below the frost line. We keep common replacement parts for these brands in our service vehicles, so when a Parkchester gate goes down, we’re not ordering from a warehouse and making the co-op wait.
Our Gate Installation team handles everything from a single pedestrian gate at a courtyard entry to a full parking lot barrier system with automated operator, safety loops, and keypad access. We don’t sub out the welding. We don’t sub out the electrical. The person you see on site is the person paid to do the job right.
Common Gate Installation Problems We See in Parkchester Homes
Parkchester’s housing stock is unlike anything else in the Bronx, and the gate problems follow the architecture.
- Corroded hinge posts in original MetLife masonry. The 1938-1942 ornamental iron gates were set directly into brick and concrete, and after 80 years, the steel at ground level is often eaten through. A new gate bolted to a failing post will sag within a season unless we cut and reset the footing.
- Freeze-thaw heaving in flat parking lots. Parkchester’s large parking facilities are flat and hold water at the gate bases. Each winter, that water freezes, expands, and racks the gate frames and operator housings out of alignment. By spring, barrier arms bind and strip the rack and pinion on the operator.
- Co-op approval delays leaving temporary panels in place too long. A simple pedestrian gate replacement can take weeks through board approval, and by the time we’re cleared, the temporary chain-link panel has already sagged. We plan for this, and we’ll tell you honestly whether the existing post can carry the new gate or whether you need a full reset.
- Identical gate models across dozens of courtyards. Parkchester’s courtyards repeat the same gate model across the entire complex. That means one failed gate usually means two or three more on the same model are about to fail. We flag this when we see it, and the co-op can decide whether to fix one or contract for several at once.
Pricing for Gate Installation in Parkchester, NY
A pedestrian gate installation in Parkchester typically runs $1,400 to $3,200, depending on whether we’re reusing the existing post or resetting it. A sliding gate for a parking lot entry runs $3,800 to $7,500, plus the operator, which adds $1,200 to $3,500 depending on brand and duty rating. A double swing gate for a wider vehicle entry runs $5,000 to $11,000 with both posts reset and both operators installed. If the work requires co-op board approval, we’ll help you put together the material specs and drawings the board asks for, and the price is quoted and agreed before any work starts. You’ll know the number before we touch a tool.
We offer free estimates on every installation, and if you’ve already got a written estimate from another company, we’ll give you a free second opinion. Call (877) 610-2993 and ask for Hal.
We Also Serve Cities Near Parkchester
If you manage a property just outside Parkchester, we work throughout the surrounding Bronx neighborhoods as well. We serve Morris Park, The Bronx, Van Nest, and East Tremont regularly, and the same Gate Installation in Parkchester team handles those jobs with the same standards and the same 90-Day Done Right Promise.
Serving Parkchester, NY - Our Local Coverage Area
We’re based in the Parkchester area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs – Gate Installation in Parkchester
Yes. Nearly every gate installation in Parkchester sits on shared co-op infrastructure, which means the property manager or co-op board must approve the materials, design, and access window before work begins. We provide whatever documentation the board needs, including material specs, drawings, and insurance certificates, and we’ll quote the job so the board’s review process doesn’t stall. Call (877) 610-2993 if you need help getting a proposal ready for your board.
Usually, yes. We weld on site, and the original Parkchester ornamental iron is heavy enough to be worth saving in most cases. We cut out the corroded sections, fabricate replacement pieces to match the original pattern, and weld them into place in your courtyard. The built work keeps the complex’s historic character, and it’s often cheaper than a full replacement. Show us the gate and we’ll tell you honestly whether it’s worth rebuilding.
We generally recommend FAAC underground operators for Parkchester’s swing gates because the housing sits below the frost line and survives the freeze-thaw cycles that wreck surface-mount units. For sliding gates, we lean toward BFT. The right operator depends on the gate’s weight, span, and duty cycle, and we’ll size it correctly when we come out. Call (877) 610-2993 with the gate location and we’ll set a time to look.
The base has to drain, and the post has to be set in a poured footing that reaches below the frost line. In Parkchester’s courtyards, standing water pools at gate bases, freezes, and heaves the track. We reset the footing, grade the base for drainage, and install the track on a solid pad. Then the gate tracks cleanly through the winter instead of binding every March.
Yes. Double gates work well on the wider vehicle entries in Parkchester’s parking facilities, especially where the entry lane is too wide for a single leaf. We set both posts into fresh poured footings, hang both leaves, and adjust the center stop so the gate closes cleanly every time. The quote includes both operators, the safety loops, and the keypad or intercom if the board wants controlled access.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Parkchester since 2001.





Before
After
Before
After
Before
After