Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in New South Memphis, TN
Gate repair in New South Memphis typically costs $180-$380 for hinge and post work, with same-day service available for most calls in the 38106 ZIP. The combination of pre-1960 housing stock, Memphis shrink-swell clay, and high-humidity lowland conditions means most gates here fail at the post footing or ground-level rust, not in the panel itself. Call (877) 610-2993 and you’ll reach a live person, 24 hours a day.
Why New South Memphis Homes Are Different
New South Memphis sits in a dense, older residential and light-industrial corridor where security fencing is a practical necessity, not an aesthetic choice. Gate systems here take a constant operational beating from high-use traffic while simultaneously corroding in Memphis’s high-humidity, flood-prone lowland air. The 38106 ZIP is dominated by pre-1960 shotgun houses, craftsman bungalows, and modest frame homes, many now rentals with years of deferred maintenance on perimeter fencing and gates.
The Memphis shrink-swell clay that underlies most of South Memphis shifts enough between wet winters and dry summers to visibly rack gate frames out of square within a few seasons. Any gate repair here that doesn’t address post depth and concrete footing integrity is almost guaranteed to be a repeat call. Original wrought iron and galvanized chain-link installations from the 1950s through 1970s are common, with corroded hinges, sagging frames, and out-of-plumb posts being the norm rather than the exception.
Standing water after heavy rains on low-lying South Memphis streets accelerates rust exactly where posts meet soil. We’ve replaced hinge posts off Florida Street that were set in the 1960s at 18 inches deep with no rebar, and they didn’t stand a chance against this clay. The housing stock and the terrain together mean we start every job by looking at what’s below ground, not just what’s swinging.
Gate Repair in New South Memphis
Gate repair in New South Memphis usually means dealing with a gate that’s older than the house’s current owner, hung on posts that have shifted in the 38106 clay, and operated by a control board that’s taken ten years of Memphis humidity. We typically get to New South Memphis within 90 minutes for emergency calls, and most hinge, post, and realignment work is finished the same day with the gate left square and latching. Gate Repair is what we’ve built our name on, and in this ZIP, that means fixing what others want to haul away.
Hinge & Post Repair
Hinge and post work is the backbone of what we do in New South Memphis. The 38106 ZIP is full of pre-1960 shotgun houses and craftsman bungalows where original wrought iron and galvanized chain-link gates from the 1950s through the 1970s are still hanging. Most have corroded hinges and out-of-plumb posts because decades of deferred maintenance finally caught up. A typical hinge or post repair in New South Memphis runs $180-$380 depending on whether we’re pouring a new footing or working with the existing one. We dig out the footing, pour concrete deep enough to hold through a wet winter, and weld or shim the hinge so the gate stops dragging.
Electric Gate Repair
Electric gates in New South Memphis get hit hard by high humidity, and older boards sealed in what was supposed to be a weatherproof enclosure eventually fail when condensation works its way in. We carry replacement boards and receivers for Viking, Ghost Controls, and DoorKing operators, so most electric repairs in 38106 don’t wait on parts. Electric and automatic gate diagnosis runs $95, and control board replacement on a Viking, Ghost Controls, or DoorKing operator typically lands between $280-$650 installed, parts included. When a summer thunderstorm passes through and a board shorts, we start with the board, then check the loop detector and the power feed, then the motor itself, in that order.
Gate Realignment
Memphis shrink-swell clay under most of South Memphis shifts enough between wet winters and dry summers to visibly rack gate frames out of square within a few seasons. A gate that latched fine in February drags by August, not because the gate sagged, but because the posts moved. Gate realignment runs $120-$250, and usually happens the same visit once the post is set. Realignment on a New South Memphis property isn’t just loosening bolts and pulling the frame back square; it’s checking post depth, footing integrity, and hinge wear so the next dry spell doesn’t undo the work.
Why does my wrought iron gate keep sagging a few months after a repair in New South Memphis?
Almost always because the hinge post is moving in the shrink-swell clay under 38106. A gate sags in the hinge post, not in the middle. If someone repaired the gate by pulling the frame back and tightening hinges without addressing the post’s footing, the next wet-dry cycle undoes it. We reset the post deep and let the concrete cure before hanging the gate, which is the only way a repair lasts. Call (877) 610-2993 for a free inspection.
Is it cheaper to replace an old slide gate operator or keep repairing the original on a rental property in 38106?
It depends on what’s failing. A control board replacement runs $280-$650, and a motor replacement is usually less than a full operator swap. But when the gearbox, motor, and board all show their age, a new operator from Viking, Ghost Controls, or DoorKing starts around $900 installed and resets the clock. For a rental property in New South Memphis, we’ll tell you plainly which one costs less over the next five years. Call (877) 610-2993 for an exact quote.
Gate Installation in New South Memphis
Gate installation in New South Memphis means dealing with clay that moves, iron that rusts at the soil line, and gates that were hung before modern safety rules existed. A new driveway gate in 38106 typically runs $1,800 to $4,500 installed, depending on whether we’re replacing a rotted post or starting from clean ground. Gate Installation here requires knowing what actually holds up against Memphis humidity and South Memphis clay, not just what looks good in a catalog.
Driveway Gate
A driveway gate in New South Memphis sits in the hardest-working part of your property. High-use traffic from rentals and working-class households means the operator cycles constantly. A single swing gate on new posts runs $1,800 to $3,200, depending on width, steel gauge, and whether we’re reusing the existing operator. We size the post footings for Memphis shrink-swell clay and set the hinges for the grade, because a gate that drags after the first wet winter was never hung right to begin with.
Sliding Gate
Sliding gates are the practical choice for narrow driveways between shotgun houses or when a swing gate would block the street. Sliding gate installations run $3,000 to $5,500, including the concrete track bed. In New South Memphis, the old chain-link sliding gates from the 1960s and 1970s often have rollers seized with rust and track sections sunk into soft ground. We pour new concrete track beds, set the post to true plumb, and hang the gate so it rolls clean through wet and dry seasons alike.
Swing Gate
Most older swing gates in 38106 were hung before frost-line and clay-swell standards required deep footings. A double swing gate runs $3,500 to $6,500. The result of shallow footings: hinge posts heave out of plumb, the gate drags at the latch side, and the frame racks out of square. We remove the old shallow footing, pour a 36-inch pier with rebar, and set galvanized posts before hanging a new steel frame. Fix the panel without the post and you’ll fix it twice. We tell you that up front.
Can you retrofit a 1960s-era swing gate in 38106 with a modern operator, or should I replace the whole gate?
It depends on the post condition and the frame itself. If the hinge posts are still plumb and the frame isn’t racked, we can weld new hinge plates and mount a modern operator like a Ghost Controls or DoorKing on the existing structure. If the posts have rusted at ground level or shifted in the clay, retrofitting is throwing money at a gate that will sag again. We’ll show you which is which before you spend a dollar. Call (877) 610-2993 for a free measure and written quote.
How deep should gate posts be in South Memphis to avoid repeat calls?
Thirty-six inches minimum, with a rebar cage and concrete pier that extends below the shrink-swell zone. Anything shallower is a temporary fix in this clay. We replaced a sagging double swing gate on a rental property off South Parkway East where the original 1960s wrought iron hinge posts had rusted at ground level and shifted out of plumb. Our crew cut out the old footings, poured new 36-inch deep concrete piers, and hung a gate that’s still square three years later. Call (877) 610-2993 for a free estimate.
Gate Motor & Opener in New South Memphis
Gate motor and opener repair in New South Memphis is rarely just an electronics swap. It’s usually a soil-and-post-footing problem wearing a motor-shaped costume. The 38106 ZIP sits on Memphis shrink-swell clay that heaves between wet winters and dry summers, and that movement racks gate frames out of square within a few seasons. When the frame shifts, the motor stalls, the arm binds, and the safety photocell faults. Gate Motor & Opener service here means fixing the footing first, then the opener.
Motor Installation
A new gate motor install in New South Memphis starts with the post, not the electronics. If the post is out of plumb or the concrete footing is shallow, the new motor is going to fight the frame from day one. A full operator replacement with new motor, control board, and remotes usually lands between $850 and $1,650 installed. We dig to the proper depth, set posts with rebar and new concrete where needed, then mount and square the operator. We install LiftMaster, FAAC, Linear, BFT, DoorKing, and Elite openers, and we’re certified on nine major brands.
Motor Repair
Most motor repair calls in 38106 come from older gates hung before modern safety requirements existed. A typical gate motor repair runs $180 to $340, depending on what’s actually wrong. The control board is obsolete. The terminal strips are corroded from Memphis humidity. The motor overloads because the hinge post shifted. We repair what can be repaired and we’re honest when replacement is the cheaper answer. That’s not a sales pitch. It’s the difference between fixing a 1970s swing gate for $200 and selling you a package you don’t need.
Slide Motor Service
Slide gates in low-lying South Memphis have a specific failure pattern. Slide gate realignment with rack reset runs $250 to $500, and if the concrete pad needs resetting that’s additional. The Memphis clay shrinks in dry summers and swells in wet winters, and that seasonal movement shifts the concrete pad the track sits on. The rack and pinion bind. The motor pulls more amps. The thermal protection trips. We realign the track, reset the rack, and when the soil is the culprit we address the footing depth so the same call doesn’t come back next spring.
Why does my slide gate motor in South Memphis bind every spring after the ground dries out?
Because the clay under the concrete track pad shrinks during dry spells and the pad settles unevenly. The rack and pinion get out of alignment, the motor pulls more current, and the gate binds halfway through its travel. The fix that lasts is resetting the pad with deeper footings below the shrink line. Quick realignments last a season. A proper footing fix lasts. Call (877) 610-2993 for a pad evaluation and written quote.
Can I put a battery backup on my FAAC swing gate operator in New South Memphis, or is that only for slide gates?
You can absolutely put a battery backup on a FAAC swing gate operator. Battery backup add-ons for existing FAAC or LiftMaster swing gate operators run $200 to $450. Power in this part of South Memphis drops every time a summer storm rolls through, and a swing gate without backup becomes a manual wrestle in the rain. We’ll size the kit to your operator and quote it before we start. Call (877) 610-2993 for details.
Gate Access Control in New South Memphis
When a gate keypad goes dead in the 38106 ZIP, you’re not dealing with a minor nuisance. You’re dealing with a home that no longer closes, a driveway anyone can pull into, or a tenant who can’t get out for work. Gate access control in New South Memphis is about more than convenience. This is a dense, older residential and light-industrial corridor where security fencing is a practical necessity. Gate Access Control systems here take a constant operational beating, and the electronics have to survive Memphis humidity and the occasional standing water at the post base.
Keypad Entry
The workhorse of New South Memphis gate access. Keypads fail here for predictable reasons: humidity eats contacts, hard rain gets into cheap seals, and renters wear buttons out. A waterproof keypad properly sealed for Memphis weather typically runs $180-$320 installed. We replace worn keypads, rewire corroded connections, and reprogram codes on site. If your keypad works partially, or only when it’s dry out, we can usually save the panel rather than replace it. That’s the repair-first philosophy. We fix the gate in your driveway, not haul it off and swap parts that don’t need swapping.
Remote Control
Your opener stops responding to the remote. Nine times out of ten, it’s not the remote. It’s a corroded antenna wire, a receiver board with a blown capacitor, or a frequency conflict from a neighbor’s system. Programming a replacement remote in New South Memphis runs $75-$150 depending on the opener model. We diagnose the actual cause before selling you a part. We service LiftMaster, FAAC, and BFT openers among others, and we keep common remote models stocked for same-visit fixes.
Phone Entry
Phone entry systems let you answer the gate from your cell and buzz someone in. For rental properties and home offices across New South Memphis, this is the most practical upgrade. Replacing a phone entry control board runs $220-$400, and programming and wiring checks run $95-$160. The Memphis cellular signal is strong across the 38106 ZIP, so connection is rarely the problem. The failure point is usually the control board or the landline transition. If your phone entry stopped calling your phone, we’ll test the board first and quote the exact fix before touching anything.
How fast can you get to New South Memphis for a gate access emergency?
We can usually reach most of the 38106 ZIP within about an hour for true emergencies like a gate stuck open or a keypad that won’t release. The drive from our Memphis office is short, and we know the neighborhood grids. When you call (877) 610-2993, a live person picks up, not a machine. Tell us the address and we’ll tell you honestly when we can be there. Estimates are always free.
What does a full gate access control install include in New South Memphis?
A full install includes the keypad, reader, or phone entry unit, wiring to the opener, programming, and testing at the gate. We also check the gate’s mechanical condition and post alignment while we’re there. If the gate doesn’t swing level, the best access control in the world won’t work for long. The price we write up covers all of that. Nothing added at the door afterward. For exact pricing, call (877) 610-2993.
Gate Parts & Welding in New South Memphis
Gate repair in New South Memphis usually comes down to two things: how the clay soil moved this season and how long the gate has been taking the humidity. We fix both. A sagging gate off Florida Street, a slide gate dragging on a shared driveway in 38106, a hinge post that’s rusted through at ground level. Gate Parts & Welding is where we save gates that other companies want to replace entirely, welding on site so your gate never leaves the driveway.
Hinge Replacement
Hinges fail in New South Memphis faster than in most places because the humidity never really lets up. A hinge replacement typically runs $180-$325 per hinge, depending on the gate’s weight and whether we need to reinforce the post while we’re there. A hinge that’s been on a 1960s wrought iron gate for fifty years has eaten enough moisture to rust from the inside out. We cut out the old hinge, weld in a new one rated for the gate’s actual weight, and we don’t pretend the post is fine if it isn’t. Fix the hinge and leave a rotten post, and you’ll call us again in eight months. We’d rather fix it once.
Post Replacement
This is the big one in 38106. Post replacement runs $350-$700 per post, including digging out the old concrete, setting the new post deeper, and rehanging the gate. The shrink-swell clay under New South Memphis moves enough between wet winters and dry summers to visibly rack gate frames out of square within a few seasons. A post that was plumb in March is leaning by August. We dig it out, set the new post deeper than the original, and pour concrete below the frost line so the soil has to work harder to move it. A new post without proper depth is just a future callback. We don’t do future callbacks.
Rail Repair & Custom Welding
Chain-link and wrought iron gates in New South Memphis have dealt with decades of moisture at ground level, where standing water sits after heavy rain. Rail repair on a corroded chain-link or wrought iron frame runs $220-$480, and custom welding is $95 an hour plus materials. Lower rails rot there first. We cut out the corroded section, weld in new steel, and reinforce the corners so the whole frame carries load evenly again. Sometimes the part your gate needs doesn’t exist anymore. A bracket, a custom latch plate, a reinforcement gusset for a sagging corner. We fabricate it in the driveway, fit it to the gate, and weld it in place. National outfits want to sell you a whole new gate because they don’t weld. We do.
How do I know if my sagging gate in New South Memphis needs hinge post replacement and not just a new hinge?
Look at the post. If the hinge itself is rusted or the pin is worn, a new hinge usually fixes it. But if the post leans, even slightly, or if you can see a gap where the concrete footing has pulled away from the soil, the post has moved. In 38106, it’s almost always the clay. A new hinge on a leaning post lasts a few months. Call (877) 610-2993 and we’ll tell you which one it is, free.
Can you weld a slide gate back into square on a shared driveway in 38106 without taking it down?
Yes. We weld in place, on site, and we keep the gate on its track while we work. Cutting out a rusted section and welding in new steel while the gate is still hung is standard for us, especially on tight shared driveways where there’s nowhere to lay the gate down. Vehicle and pedestrian access stays open the whole time. Call (877) 610-2993 to schedule.
Brands We Service in New South Memphis
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common boards, remotes, and receivers for Viking, Ghost Controls, and DoorKing operators locally, so most New South Memphis repairs don’t wait on parts. Turnaround on a standard electric gate repair is usually same day once we’re on site. our brands
Pricing for Gate Repair in New South Memphis, TN
| Service | Typical Range in New South Memphis |
|---|---|
| Hinge & post repair | $180-$380 |
| Gate realignment | $120-$250 |
| Electric/automatic gate diagnosis | $95 |
| Control board replacement (installed) | $280-$650 |
| Full operator replacement | $900+ |
| Single swing gate installation | $1,800-$3,200 |
| Double swing gate installation | $3,500-$6,500 |
| Sliding gate installation | $3,000-$5,500 |
| Gate motor repair | $180-$340 |
| Full motor/opener replacement | $850-$1,650 |
| Keypad replacement (waterproof) | $180-$320 |
| Post replacement | $350-$700 |
What pushes price up in New South Memphis is almost always post work: digging out old concrete from the 1950s or 1960s, pouring deeper footings with rebar to beat the clay, and dealing with rust at ground level where standing water has done its damage. Every quote is a firm number, agreed before any work starts, and the number we give you on the phone is the number we honor in person. We also take $40 off any repair over $200, there’s no trip charge inside the county, and seniors and veterans get 10% off, every job.
Neighborhoods We Serve in New South Memphis
We work throughout the 38106 ZIP, and we’re usually at your gate within a couple of hours for repairs, depending on the time of day. The streets we serve regularly include:
- Areas along Elvis Presley Boulevard south of McLemore
- The residential blocks around Southside High School
- Streets off Porter and Lauderdale near the old industrial corridor
- Homes around Georgia Avenue and the Belt Line
- Neighborhoods east of Airways Boulevard toward I-240
Service Area - Cities Near New South Memphis
We run gate repair and installation calls across Shelby County and into the surrounding communities from our Memphis office. If you’re looking for service in New South Memphis, TN, Memphis, TN, Germantown, TN, Bartlett, TN, Millington, TN, or Lakeland, TN, the same crew and the same standards apply. No call centers, no dispatch queues, no passing you between three different people.
Serving New South Memphis, TN - Our Local Coverage Area
Gatewood Fence & Gate crews serve New South Memphis and the communities around it; dispatch is coordinated from our Memphis office. The map shows the New South Memphis coverage area; if your address is on it, we can help.
Also serving nearby: New South Memphis, TN, Memphis, TN, Germantown, TN, Bartlett, TN, Millington, TN, Lakeland, TN.
FAQs About Gate Repair in New South Memphis
Yes. We cover the entire 38106 ZIP, from the residential streets near the old industrial corridors up to the neighborhoods bordering Memphis proper. We’re a local shop, not a national outfit, so we don’t sort you into a far-off dispatch system. We know the area, and we’re already on the road here most days. Call (877) 610-2993 for a free estimate.
No, not meaningfully. The cost is driven by the equipment and the condition of the existing gate, not by the ZIP code. That said, older gates in the 38106 ZIP often need extra post-leveling or hinge work before access control can be installed properly, which adds labor. We quote that honestly up front. The gate access control hardware itself runs the same ranges as Memphis or Germantown. For senior and veteran discounts, call (877) 610-2993.
Every job carries our 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back, no runaround. That’s not a marketing line. It’s stamped on every invoice, and the phone number on it is answered by a live person. If you have a problem within 90 days, call (877) 610-2993 and we’ll come back.
Ready to get your gate fixed right? Call (877) 610-2993 for a free estimate. A live person answers 24 hours a day, and we’ll give you a firm price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What New South Memphis Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond