Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Lynwood, CA
When a driveway gate stops opening in Lynwood, the problem usually traces back to two things: rust from the marine layer that settles on bare metal overnight, and hinge posts that were never set deep enough in the first place. We fix both, and we do it in your driveway, not by hauling your gate off to a shop somewhere. Call (877) 610-2993 and you’ll get Hal or one of his crew on the line, not a recording.
Why Lynwood Homes Are Different
Lynwood’s housing stock was mostly built in the 1940s through the 1960s, which means almost every driveway gate here was retrofitted years after the original construction. A huge share of those gates were welded up by informal local fabricators between roughly 1985 and 2005, using whatever post spacing and frame dimensions felt right at the time. We see hinge centers that match no retail bracket and posts set only a foot deep in soil that shifts.
Then there’s the climate. Lynwood sits close enough to the coast for the marine layer to drop moisture on everything metal overnight, and far enough inland to catch particulate drifting from the I-710 corridor and nearby industrial zones. That combination eats through chipped paint and thin-gauge tubing faster than it does in drier cities twenty miles east. Gates in the 90262 ZIP rust through on the bottom rail five to ten years sooner than identical gates in Downey or Whittier. We treat rust as a structural issue, not a cosmetic one.
Garage-to-ADU conversions have also changed driveway footprints across town. When the driveway shifts, the old gate no longer lines up with the opening, and that misalignment slowly destroys hinges and operator mounts. These are Lynwood-specific realities we deal with every week, and they change how we approach every repair.
Gate Repair in Lynwood
Gate repair in Lynwood usually comes down to three problems: a gate that won’t open, a gate that won’t stay closed, or a gate that drags on the concrete because it’s sagging. Most of the time we can diagnose and fix all three the same day we arrive. The key difference between our approach and what you’ll get from a national outfit is that we repair what’s there rather than selling you a replacement you don’t need. Hal Gatewood has been fixing gates since 2001, and the work still happens in your driveway. Our full Gate Repair service covers everything below, and a live person answers when you call (877) 610-2993.
Electric Gate Repair
A 1990s-era DoorKing or FAAC operator on a Lynwood gate is a different animal than a new LiftMaster off the shelf. The control boards on those older units often can’t accept modern safety photocells, which means the gate can’t meet current UL 325 entrapment protection standards without a retrofit. We swap in retrofit boards so you keep the original motor and get compliant safety. Electric gate repair in Lynwood typically runs $225 to $480 depending on whether we’re replacing a capacitor, rewiring limit switches, or swapping a dead board.
Hinge & Post Repair
Lynwood’s compacted soil shifts more than homeowners expect, and many gates here were set with shallow footings by welders who never poured to spec. When the post leans, the gate binds, and every cycle adds wear to the hinges and the operator. We reset posts in fresh concrete, fabricate custom hinge brackets when the spacing is non-standard, and get the gate swinging free again. Hinge and post repair usually runs $180 to $400 per post, depending on footing depth and whether we need to open up concrete around the base.
Weld & Rust Repair
The marine layer rolls in overnight and leaves moisture on bare iron, and the I-710 corridor adds particulate that grinds into chipped paint and starts oxidation fast. We cut out rusted sections, weld in new steel on site, and treat the repair so it doesn’t come back in a year. Weld and rust repair in Lynwood typically runs $150 to $350 per affected section, depending on how much steel has to be replaced.
Gate Realignment
A sagging gate usually isn’t a gate problem at all. It’s a hinge post problem, a worn hinge barrel problem, or both. We re-hang the gate rather than cranking on adjusters, which is what keeps it from dragging again in six months. Gate realignment in Lynwood runs $150 to $280 for a standard single driveway gate, more if we’re also correcting the rack and pinion on a slide gate.
Why do so many Lynwood gates have non-standard hinge spacing that off-the-shelf parts don’t fit?
Because a large share of Lynwood’s gates were fabricated and hung by informal local welders between roughly 1985 and 2005, not by licensed contractors working from standard templates. Those welders used whatever spacing felt right, so we regularly encounter hinge centers that don’t match any retail bracket. We fabricate custom hinge brackets on site rather than forcing a standard part. Call (877) 610-2993 and we’ll take a look.
My 1990s automatic gate still works but trips the circuit breaker. Is the operator failing, or is it a Lynwood-specific power issue?
It’s usually the operator drawing more current than it should, not the power coming into your house. Older Lynwood gates often have worn capacitors, corroded motor windings, or binding that makes the motor work too hard and trip the breaker. We test the amp draw first. If it’s a board or capacitor, we replace it for $225 to $480. If the motor’s done, we’ll quote a replacement before doing anything.
Gate Installation in Lynwood
Gate installation in Lynwood is a different job than in the newer developments further east. Most homes here were built in the 1940s through the 1960s, and nearly every driveway got a wrought-iron or tubular-steel gate added years later. That means we’re rarely working with clean, square openings. We’re shimming posts on settled concrete, matching existing fence lines, and cutting panels to fit driveways that have shifted over six or seven decades. Our Gate Installation work starts with careful measurement, not assumptions.
Driveway Gate Installation
Most Lynwood driveways fall into one of two camps: narrow single-car openings where every inch matters, or wider double openings that were poured decades ago and aren’t perfectly level anymore. We measure on site, account for the slope, and build the gate to swing or slide cleanly without scraping on the uphill side. For homes near Plaza Mexico or along Imperial Highway, we also factor in foot traffic; a gate that sticks in the open position invites trouble from a busy sidewalk. Custom driveway gate installations typically run $1,800 to $3,800 for a single swing gate, depending on width and whether we can reuse existing hinge posts.
Pedestrian Gate Installation
Pedestrian gates in Lynwood get more use than driveway gates. Kids walk through them every day, and so do mail carriers, gardeners, and grandkids. We hang them so they don’t sag at the latch after six months, and we match the metal to your existing fence. Most pedestrian gate installs in the 90262 run $450 to $1,100 depending on width, metal thickness, and whether it’s a simple latch or a keypad entry.
Sliding Gate Installation
Sliding gates make sense on Lynwood lots where a swing gate would block the sidewalk when open or clip a car parked on the street. They also take up less room inside a tight driveway. We install the recessed track, set the roller post, and align the gate so it moves with one hand even before the operator goes on. Sliding gate installs in Lynwood typically run $2,800 to $5,500 depending on length and material. Every quote is written and itemized before we start.
How long does a gate install take in Lynwood?
Stock steel pedestrian gates can usually be measured, fabricated, and installed within five to seven business days. Custom driveway gates take two to three weeks depending on width and any welding we need to do in your driveway. Call (877) 610-2993 and we’ll give you a straight timeline for your specific opening.
Do I need a permit to install a driveway gate in Lynwood?
Most residential gate installations in Lynwood don’t require a separate building permit if the gate matches existing fence height and stays within your property line. Anything taller than 6 feet or attached to new masonry columns can trigger a permit check with the city. We’ll tell you before we start, not after, and you always get the written quote first.
Gate Motor & Opener in Lynwood
Gate motor repair in Lynwood typically runs $240 to $480 for a board or limit switch replacement, while a full operator swap on an ornamental iron driveway gate usually lands between $950 and $1,800 depending on the motor and mounting work involved. Most of the calls we get involve gates that have stopped responding, started grinding, or reversed mid-cycle for no obvious reason. The fix usually comes down to one thing most companies skip: looking at the post the motor is mounted on. Our Gate Motor & Opener service treats the operator and the post as one system.
Motor Repair
Most gate motor failures in Lynwood start with the mount, not the motor. When a hand-welded hinge post from the 1990s leans even a few degrees, it binds the drive arm and trips the thermal overload. We straighten or rebuild the post first, then address the motor. That’s why our motor repairs last here. A typical motor repair in Lynwood runs $240 to $480 when the board, capacitor, or limit switch is the culprit. If the motor itself is burned out, swapping in a new unit on the existing post is usually $950 to $1,800.
Linear Motor
Linear operators are common on Lynwood’s slide gates, especially along commercial-adjacent streets off Atlantic and Long Beach Boulevard where driveway widths allow a slide run. The motor itself is straightforward, but the failure point is usually the rack and pinion eating itself because the gate post shifted from moisture-warped concrete or rusted anchor hardware. We stock Linear motors and replacement racks locally, so Lynwood jobs don’t wait on parts from a warehouse three states away. Cost to replace a Linear slide motor runs $1,300 to $1,900 installed, corrected and tuned.
Slide Motor
Slide gate motors in Lynwood fail most often at the pickup and limit points, not in the motor housing. The I-710 corridor puts fine particulate in the air that grinds into plastic limit cams and rail bearings faster than you’d see in Lakewood or Cerritos. We clean, shim, and lubricate the entire slide path when we service a slide motor here, because replacing just the motor on a gritty rail means a comeback in six months. Slide motor repair runs $280 to $520; full replacement with rail cleanup runs $1,400 to $2,200.
Do I need battery backup on my gate opener if I live near the I-710 in Lynwood?
Yes, especially if your gate is the only vehicle access point. Power along the I-710 corridor isn’t the most reliable in LA County, and a dead gate during a blackout is a safety problem, not just an annoyance. Battery backup adds $300 to $550 to a Lynwood installation and pays for itself the first time the power blinks and the gate still opens.
How does the marine layer affect the loop detector under my Lynwood driveway?
Moisture seeps into hairline cracks in older Lynwood driveways, especially where saw-cut loop channels were sealed improperly years ago. Combined with vibration from I-710 truck traffic, the loop wire’s insulation abrades and water intrusion drifts the inductance reading, so your gate won’t detect your car or false-detects constantly. We re-cut, re-bed, and seal the loop properly so it stays dry. Loop repair runs $180 to $350 in Lynwood.
Gate Access Control in Lynwood
Gate access control in Lynwood means matching the entry system to how the property actually gets used. A keypad that works fine on a quiet cul-de-sac may not survive constant use on a busy corner off Long Beach Boulevard. We install and service keypads, intercoms, telephone entry systems, and vehicle loop detectors, and we make sure the whole setup talks to whatever operator is already on the gate. Our Gate Access Control work always starts with a look at the existing wiring and the operator, because adding a modern access system to a 1990s operator sometimes requires a retrofit board first.
Keypad & Intercom Systems
Lynwood’s mix of single-family homes and duplexes means plenty of gates serve more than one household. A keypad or intercom with multiple codes and a call button makes sense there, and we wire it so the system doesn’t fight the operator’s control board. Keypad and intercom installs in Lynwood typically run $400 to $900 depending on the hardware and wiring work. We only quote after seeing the existing setup, and the quote is fixed before work starts.
Vehicle Loop Detectors
Loop detectors are what tell your gate a car is waiting to exit or enter. In Lynwood, the same moisture that shortens gate paint life also works its way into loop channels if the sealant has failed. We diagnose false triggers and no-trigger failures by testing the loop’s inductance first, then we repair or replace the loop. Loop detector repair or replacement in Lynwood runs $180 to $350.
Can you add a keypad entry to an old Lynwood swing gate without replacing the whole operator?
Yes, in most cases. A 1990s FAAC or Viking operator can often accept a retrofit board that talks to modern keypads and intercoms, which brings it up to current safety and access standards without swapping the motor. If the original board is completely obsolete and no retrofit kit exists, we’ll tell you that honestly and quote an operator replacement instead. Call (877) 610-2993 and we’ll check your setup.
Do you service access control on gates that were hand-welded by a local fabricator?
Yes. Non-standard mounting surfaces are common on Lynwood’s older hand-welded gates, so we fabricate adapter plates and brackets on site to mount keypads, intercoms, and gate arms cleanly. We adapt the hardware to the gate, not the other way around. Call (877) 610-2993 for a free estimate on access control in Lynwood.
Gate Parts & Welding in Lynwood
Gate parts and welding in Lynwood often comes down to one question: can someone fix this at my house, or do I have to haul a 200-pound gate off its hinges and wait a week? We fix it at your house. The 90262 ZIP is full of ornamental iron gates from the 1985 to 2005 era, and after 20 to 35 years those hinges, posts, and rails are giving out all over town. We carry the common parts, and we weld on site. Check our Gate Parts & Welding page for more detail.
Hinge Replacement
Worn or seized hinges are the single most common call we get in the 90262 area. Lynwood’s older iron gates were often hung on barrel hinges that were undersized for the weight, and after 25 years they oval out and the gate sags. We cut the old ones off, weld in new ones, and align the gate so it swings clean. A typical hinge replacement in Lynwood runs $150 to $320 depending on how many hinges and whether we’re doing both the driveway and pedestrian gates.
Post Replacement
A sagging gate usually starts at the post, not the middle. Lynwood’s 1940s to 1960s homes were built before most gates existed, so posts were retrofitted into existing concrete and sometimes only set 12 inches deep. That’s not enough. We dig out the old post, set a new one properly, and weld the frame back square. Post replacement here typically runs $280 to $550, and you’ll have the full price before we touch a tool.
Rail Repair
Rust hits the bottom rail first where water collects. Near the I-710 corridor and under the marine layer, Lynwood gates rust through faster than homeowners expect. We cut out the bad section, weld in replacement steel, and grind it smooth so the gate doesn’t look patched. Rail repair in Lynwood usually falls between $180 and $400 depending on how much of the rail is compromised.
Can you do emergency welding if my gate is hanging by one hinge in Lynwood?
Yes. If your gate is down or dangerous, we prioritize it. A heavy iron panel hanging loose is a real safety risk, so don’t try to muscle it back into place yourself. Call us and stay clear until the crew arrives. We bring the welder and the parts to your driveway in Lynwood and usually finish the repair the same day.
What kind of warranty do you offer on parts and welding in Lynwood?
Every gate parts and welding job in Lynwood carries our 90-Day Done Right Promise in writing. If something’s not right within 90 days, one call brings Hal back to make it right. No charge, no runaround. Call (877) 610-2993 for details or a free quote.
Brands We Service in Lynwood
We service FAAC, BFT, Linear, and Viking operators across the 90262 ZIP, along with LiftMaster, DoorKing, Ghost Controls, Elite, and Mighty Mule. We stock common boards, capacitors, and limit switches for the brands we see most in Lynwood, which keeps turnaround short. See our brands page for the full list.
Pricing for Gate Repair in Lynwood, CA
| Service | Typical range in Lynwood |
|---|---|
| Gate realignment | $150 - $280 |
| Weld & rust repair (per section) | $150 - $350 |
| Hinge replacement | $150 - $320 |
| Post replacement | $280 - $550 |
| Electric gate repair | $225 - $480 |
| Hinge & post repair (per post) | $180 - $400 |
| Loop detector repair | $180 - $350 |
| Motor repair | $240 - $480 |
| Swing gate operator replacement | $950 - $1,800 |
| Slide gate operator replacement | $1,400 - $2,200 |
| Pedestrian gate installation | $450 - $1,100 |
| Custom welding | $120 - $450 |
What pushes a Lynwood job toward the higher end? Deep post excavation in compacted soil, ornamental gates that need an extra set of hands, and rust that spread further than it looked. Whatever the number, the price is quoted and agreed before any work starts, and it doesn’t move at the door.
Neighborhoods We Serve in Lynwood
We cover the entire 90262 ZIP. Response for most Lynwood repair calls is same-day, depending on when you reach us.
- Residential streets around Lynwood High School
- Blocks off Atlantic Avenue
- Quiet courts east of Long Beach Boulevard
- West Lynwood near the I-710 corridor and Imperial Highway
- Areas around Plaza Mexico
Service Area - Cities Near Lynwood
We serve Lynwood, CA and the surrounding communities, including South Gate, CA, East Rancho Dominguez, CA, Willowbrook, CA, Paramount, CA, and Huntington Park, CA. If you’re on the edge of any of these cities, give us a call and we’ll tell you straight whether we cover your block.
Serving Lynwood, CA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Lynwood and the communities around it; dispatch is coordinated from our Los Angeles office. The map shows the Lynwood coverage area; if your address is on it, we can help.
Also serving nearby: Lynwood, CA, South Gate, CA, East Rancho Dominguez, CA, Willowbrook, CA, Paramount, CA, Huntington Park, CA.
FAQs About Gate Repair in Lynwood
We can typically reach Lynwood within 60 to 90 minutes for urgent gate failures, especially if you’re near Imperial Highway, the I-710 corridor, or the residential streets off Martin Luther King Jr. Boulevard. A live person answers the phone 24/7, so you’ll know right away when someone’s coming. Call (877) 610-2993.
Yes, we cover the entire 90262 ZIP, from the compact residential blocks near Lynwood Park to the mixed-use streets along Long Beach Boulevard. We know the housing stock here: mostly 1940s to 1960s single-family homes and duplexes with retrofitted ornamental gates. You won’t spend the first half hour explaining where you live.
Pricing is basically the same across Lynwood, South Gate, and the surrounding area, because the same crew and the same parts truck serve all of them. What changes the price is the gate itself: older ornamental iron with non-standard hardware can take more labor than a newer tube-steel gate. Typical repairs in Lynwood run $150 to $550.
If your gate is acting up in Lynwood, call (877) 610-2993 for a free estimate. You’ll talk to a live person who knows the 90262 streets, and you’ll get a straight answer before anyone sets foot on your property.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Lynwood Customers Say
"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo