Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Lone Tree
Gate installation in Lone Tree usually means dealing with an HOA architectural review, a hillside driveway with expansive clay soil, and a gate that has to match the rest of the subdivision. Most of our installations here run $2,800 to $7,500 for a complete automated driveway gate, and we handle the whole thing: permits, HOA coordination, post footings, operator, safety edges, and final inspection. If you’re in the 80124 zip code, call Hal at (877) 610-2993 and we’ll come measure, quote a written price, and stand behind it. We’ve worked on gates in Heritage Hills, RidgeGate, and the neighborhoods off Lincoln Avenue since long before they started failing all at once.
Why Gatewood Fence & Gate Is Lone Tree’s Preferred Gate Installation Company
Hal Gatewood has been doing this since 2001, and he lives the principle that your gate should stay in your driveway while we work on it. We weld on site. We don’t haul your gate to a shop somewhere and hope we get it back to you intact. Homeowners in Lone Tree have dealt with plenty of outfits that quote a number on the phone and present a different one at the door. That’s not how we operate. The price we write down before we start is the price you pay. Period.
If something isn’t right after the install, the 90-Day Done Right Promise kicks in. It’s in writing on every invoice. One call brings Hal back, no charge. That guarantee matters in Lone Tree because a gate that racks or binds by spring has a lot to do with what’s happening under the ground before we ever mount the operator. We dig the footings deep enough to handle the soil we know we’re going to find.
We answer the phone. Not a voicemail, not a chatbot, not a call center. A live person. Around the clock. When you call about a gate that won’t open at 7 a.m. before work, you get a real human who knows what a swing gate is. You can also drive to the shop and look Hal in the eye before you ever sign anything. That’s the kind of accountability national companies can’t offer in Lone Tree.
Our Gate Installation Services in Lone Tree
Driveway Gate Installation
A driveway gate in Lone Tree often spans a wide entrance cut into a hillside. We measure the opening, check the slope, and engineer the hinge posts to resist the bentonite clay heave that moves everything come spring. Whether you’re on a flat lot in the Fairways or a sloped driveway north of Lincoln, we match the finish to your community’s spec.
Pedestrian Gate Installation
Pedestrian gates in Lone Tree’s patio home and townhome communities usually have to match an existing streetscape. We coordinate with the HOA’s architectural control committee so the aluminum or steel pickets, the powder-coat color, and the latch style line up with what your neighbors already have. These are smaller jobs, usually $800 to $2,200 installed, but the HOA piece takes coordination most installers won’t bother with.
Sliding Gate Installation
Sliding gates make sense on Lone Tree lots where a swing gate would eat too much driveway or climb a slope. We build the track, set the posts on deep footings, and install operators from brands like FAAC and BFT that are rated for the cycles these gates see. RidgeGate-area communities especially. Many of the original operators from the early 2000s are dying now, and we’re replacing them street by street.
Swing Gate Installation
Most ornamental steel driveway gates in Lone Tree are swing gates. Single and double. The challenge here isn’t the gate itself. It’s the post. Bentonite soil freezes and swells, and a post that wasn’t set deep enough will lean by March. We set posts below the frost line with proper concrete encasement. Then we hang the gate, mount the operator, wire the safety edges and photocells, and adjust the close pressure so the gate never tries to crush a car or a person.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lone Tree
We service and install nine major gate operator brands, and in Lone Tree we most often see FAAC, BFT, Linear, and Viking units in the older subdivisions. We keep common boards, motors, and safety parts in our local stock so a new install doesn’t stall waiting on a shipment. Hal and his crew are certified on all the major lines, including LiftMaster and Elite, which show up all over the early-2000s communities near RidgeGate. When we install an operator, we’re installing something we’ll service ourselves later. That changes the way we pick the gear.
Common Gate Installation Problems We See in Lone Tree Homes
- Heaving posts from expansive clay soil. Every freeze-thaw cycle moves the soil, and by spring a perfectly aligned swing gate is racking or the latch won’t catch. New installations need deeper footings than a flatland spec calls for.
- Hail-damaged operator housings and keypads. Front Range hail pounds equipment. We install weather-resistant enclosures and use touch-up coatings that hold up better than the factory finish.
- Original operators failing at the same time across a subdivision. Lone Tree was built out fast in a narrow window, so entire neighborhoods have the same operator reaching the same end of life. We repair rather than replace when the frame is sound, but when a unit is finished, we know exactly what to put in.
- Long driveways with no practical power source. This shows up in the acreage and wide-lot sections of Lone Tree. Solar gate openers with deep-cycle battery banks and loop detectors at the road edge solve what a trench and conduit never will.
Pricing for Gate Installation in Lone Tree, CO
Here’s what we see on the ground in Lone Tree. These are all-in ranges for a typical installation, including materials, labor, and safety equipment.
| Gate Type | Typical Installed Range |
|---|---|
| Driveway Gate | $0-$0 |
| Pedestrian Gate | $0-$0 |
| Sliding Gate | $0-$0 |
| Swing Gate | $0-$0 |
| Double Gate | $0-$0 |
| Security Gate | $0-$0 |
Your quote gets written down before any work starts. It doesn’t change at the door. We don’t charge a trip fee inside the county, and we’ll give you a free second opinion on any written estimate you’ve already gotten from another company. Seniors and veterans get a permanent 10% discount. If the job is over $200, take $40 off the top. Call (877) 610-2993 and we’ll come measure and hand you a number.
We Also Serve Cities Near Lone Tree
Most of our customers come from the Lone Tree area, but we run crews into Dove Valley, Castlewood, Centennial, and Southglenn the same week you call. If you’re across the county line but still in the metro, call us. We’ll tell you straight whether we can get to you that day. Our Gate Installation team keeps the same written-pricing promise everywhere we go.
Serving Lone Tree, CO - Our Local Coverage Area
We’re based in the Lone Tree area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Lone Tree
Solar is usually the answer. We install solar gate openers with a deep-cycle battery and a panel sized for Colorado’s sun, then mount a loop detector at the road edge so the gate starts opening as your car approaches. For very long driveways in the wider-lot sections of Lone Tree, this is more reliable than trenching conduit to a transformer that might be a hundred yards away. We recently did exactly this on a RidgeGate-area property, replacing an original 2004 Elite operator with a solar unit and a new keypad entry. It’s been through one full winter and hasn’t missed a cycle. Call (877) 610-2993 and we’ll look at your property and tell you what the power solution will cost.
Almost always yes. Lone Tree is nearly all master-planned HOA-governed subdivisions, and nearly every one has an architectural control committee that must approve gate materials, colors, and finishes before work begins. This is the piece most out-of-town installers miss, and it’s why we handle it. We submit the drawings, the finish samples, and the spec sheets. If the committee wants a different powder-coat tone or a specific picket spacing, we adjust before we order anything. It adds a step, but it keeps you out of a fight with your HOA later.
A sliding gate or a double swing gate. For very wide openings, a sliding gate needs less room to operate and holds up better on sloped ground. Double swing gates look traditional and work well on flat or gently sloped driveways, but the posts have to be set deep to survive the bentonite clay soil. We’ll look at your opening, your slope, and your HOA’s finish standards, then recommend the one that fits. Estimates are free, and the price is written down before work starts. Call (877) 610-2993.
Sometimes, but usually not. If the post is leaning, the footing is failing or the post itself is bent at the base. We dig it out and look. If the steel is sound, we can pour a deeper footing and reset it. But if Lone Tree’s freeze-thaw cycles have worked it loose, the new footing needs to be below the frost line, and that often means a new post set properly. We’ll tell you either way before we quote. You won’t pay for a new post you don’t need.
Yes. Every automated gate we install has to meet UL 325 entrapment standards. That means photocells or safety edges across the opening so the gate stops and reverses if anything is in the path, plus proper close-force settings. We install these on every gate, every time, no exceptions. A gate that can close on a child or a dog isn’t a gate we’ll put our name on. Hal’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lone Tree since 2001.