Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Corona
A new driveway gate in Corona typically runs $1,900 to $6,800 for a standard single swing gate, while sliding gates for wider openings start around $3,400 and can reach $12,000 for automated double-track systems. Installation usually takes one to two full days once materials arrive and any HOA approval clears. If you’re in Sycamore Creek, Dos Lagos, Terramor, or anywhere along the Temescal Valley corridor, we already know the routine: architectural review first, then the work. Call (877) 610-2993 and a live person answers, day or night.
We’re not a national outfit sending somebody out from two counties over. Gatewood Fence & Gate is Hal Gatewood’s company, owner-operated since 2001, with a published address and a license number anybody in Corona can look up. When you call about Gate Installation, you get Hal or someone from his crew who knows exactly what Corona’s HOA boards, wind patterns, and summer heat do to a gate.
Why Gatewood Fence & Gate Is Corona’s Preferred Gate Installation Company
Hal has been welding, hanging, and automating gates since 2001, and his shop is close enough that Corona homeowners see him at the hardware store. That’s why we offer Gate Repair - Corona with real accountability. That’s the kind of accountability that matters when a gate motor burns out in July or a Santa Ana gust bends a hinge post in October. We show up when we say we will, with the right parts on the truck.
Our Corona customers call us because the name on the invoice matches the name on the shop. Every job carries the 90-Day Done Right Promise in writing. If something isn’t right, one call brings Hal back. No runaround, no ticket number, no voicemail.
We answer the phone with a live person 24 hours a day, 7 days a week. Not a call center. Not a chatbot. When your gate won’t open at 6 a.m. and you’re stuck in the driveway before work, that matters.
Our Gate Installation Services in Corona
Driveway Gate Installation
Driveway gates are what we install most in Corona, especially in the 1990s-2010s tract developments where ornamental wrought-iron and powder-coated steel gates are basically standard. A wide RV-access side gate is common too, and we build those to handle the extra wind load that Temescal Canyon delivers every fall. We handle new posts, hinges, gate leaf fabrication, and automation if you want it.
Swing Gate Installation
Swing gates make up the bulk of residential driveway gates in Corona. The biggest local issue we see is under-spec’d hinge posts. In Santa Ana wind events, a gate becomes a sail. If the post wasn’t set deep enough in concrete, the gate bends the post or rips the hinges clean out. We set posts below the frost line and size them for Corona’s wind reality, not a calm afternoon in Irvine.
Sliding Gate Installation
Sliding gates work well when your driveway slopes upward from the street or you don’t have room for a gate to swing inward or outward. We install chain-driven and rack-and-pinion sliding gates on steel track or cantilever systems. In Corona, we see a lot of sliding gates on properties along Temescal Canyon Road and in newer developments where driveways are short and steep.
Pedestrian Gate Installation
Pedestrian gates are the smaller side entries, often matching a driveway gate in finish and style. We fabricate these to match HOA specs, powder-coat included. A pedestrian gate needs a solid post, a quality latch, and on some properties, an electric strike tied into our Gate Access Control in Corona. We do the whole thing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Corona
We stock and service FAAC, BFT, and Linear gate operators, along with LiftMaster, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your HOA or existing system runs one of these brands, we can match it. For Corona homeowners, having parts close by means a failed control board doesn’t mean a two-week wait. We keep common boards, remotes, and safety sensors on hand for the brands we see most in Temescal Valley and North Corona.
Common Gate Installation Problems We See in Corona Homes
Corona’s specific conditions create a predictable set of problems. Here’s what we run into regularly:
- HOA approval delays. In Temescal Valley (92883) and North Corona (92880), architectural review boards often require specific gate colors, powder-coat finishes, and hinge placements. That approval can take anywhere from a week to six weeks. We’ve had replacement gates sit in our warehouse waiting on a board decision while the homeowner’s old gate sits unusable. We stage the work so installation happens within days of approval, not weeks.
- Santa Ana wind damage to hinge posts. Gusts channeled through Temescal Canyon hit newly installed gates hard. If a hinge post isn’t set deep in concrete, the gate sags within the first fall season. We’ve corrected plenty of other companies’ installations where the post was only 18 inches deep. Ours go 36 to 42 inches, sometimes deeper in sandy soil.
- Summer heat warping wooden gates. Corona routinely pushes past 105°F in July and August. A wooden gate that isn’t properly sealed and framed for that heat warps within the first season. We use kiln-dried lumber, steel reinforcement where needed, and sealant rated for inland heat, not coastal humidity.
- Hard water rust on steel frames. Corona’s water is hard. When irrigation spray hits a steel gate frame season after season, mineral scaling and rust accelerate. We recommend powder-coating over paint for any steel gate in Corona, and we treat hinge points with corrosion-resistant grease during installation.
Pricing for Gate Installation in Corona, CA
Here is what Corona homeowners can expect, based on the jobs we’ve done across 92882, 92883, 92877, and 92878:
- Standard single swing driveway gate (wrought iron or steel, manual): $1,900 to $4,100
- Automated single swing gate (operator, safety sensors, remotes): $3,400 to $6,800
- Double swing gate (automated, both leaves): $5,200 to $9,500
- Sliding gate (steel, automated, track or cantilever): $3,400 to $12,000 depending on width and operator type
- Pedestrian gate (matching finish, installed): $800 to $2,600
- Solar gate opener for existing gate: $1,700 to $3,800 installed
What moves the price in Corona: HOA-mandated finishes (matte black powder-coat, for instance, costs more than standard paint), the width of your RV access gate, whether we’re pulling a new power run or going solar, and soil conditions that affect post depth. We quote every price before work begins, in writing. The number you agree to is the number you pay. Call (877) 610-2993 for a free estimate.
We Also Serve Cities Near Corona
Gatewood Fence & Gate handles gate installation throughout the surrounding area, including Home Gardens, El Cerrito Corona, Eastvale, and Norco. If you’re just outside the Corona city line, we still come to you with the same pricing and the same warranty. Gate Installation in Corona is our home turf, but we cover the whole west end of Riverside County.
Serving Corona, CA - Our Local Coverage Area
We’re based in the Corona area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Corona
Yes, in almost every Temescal Valley development, HOA architectural approval is required before installation can begin. This applies to gate color, finish type, hinge placement, and sometimes gate height. We have worked with the boards in Sycamore Creek, Dos Lagos, and Terramor, and we can help you prepare the submittal package. We do not start work until the approval letter is in hand, because starting early gets you a violation notice, not a gate. Call (877) 610-2993 and we will walk you through the approval process we already know inside and out.
Yes, we routinely integrate new gate operators with existing community entry systems in Corona’s gated and HOA-managed neighborhoods. If your community uses a specific keypad protocol, transponder, or phone-based entry system, we match the operator to that system. We have worked with Linear and FAAC operators tied into multi-resident access panels throughout North Corona and the Temescal Valley corridor. The first step is knowing what your board already runs, so bring us the system specs and we will take it from there.
We size the hinge posts for wind load and set them 36 to 42 inches deep in concrete, which is deeper than most installers bother with. We also use ball-bearing hinges rated for a heavier gate than you’re actually hanging, and we weld or bolt an anti-sag diagonal brace across the gate frame. A gate sags in the hinge post, not in the middle, and that’s where we start. If your existing gate has already sagged from a Santa Ana blow, we can straighten the frame and reset the posts with Gate Parts & Welding in Corona, without replacing the whole gate.
Automatic gates in Corona must meet state and national safety standards, which means photo-eye sensors on both sides of the gate path, force-sensing reverse capability on the operator, and audible alarms where required. We wire in safety photocells on every automated gate we install, regardless of whether the existing system had them. We also set the open and close force limits conservatively so the gate stops and reverses if a child or pet is in the path. These are not add-ons; they are part of the job.
Yes, if the solar panel is mounted where it gets direct sun, not on a shady wall or under a tree canopy. North Corona and Temescal Valley have strong inland sun, so solar openers work well here when installed correctly. The panel needs clean southern exposure and the battery needs to be sized for the gate’s daily cycles. We recently installed a Ghost Controls solar opener on a double swing gate in Sycamore Creek, where the HOA required a matte black powder-coat finish and concealed hinges. We coordinated the architectural approval first, then set the new hinge posts and wired a safety photocell before final inspection. For a shaded driveway, we may recommend a remote panel placement or a hardwired operator instead. Call (877) 610-2993 and we will tell you what your specific driveway can support.
Call Gatewood Fence & Gate for Gate Installation in Corona
If you need a new driveway gate, a replacement swing gate, or a solar operator on your existing gate, call (877) 610-2993. Hal or someone from his crew answers, day or night. You’ll get a free estimate, a written price before any work starts, and the 90-Day Done Right Promise on every job. The name is on the shop, and the shop is close enough that you can drive over and look him in the eye. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Corona and the surrounding Inland Empire since 2001.