Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Coatesville
Gate installation in Coatesville runs between $1,800 and $6,500 for most residential jobs, depending on the gate type, post condition, and whether we’re retrofitting existing ironwork or setting fresh footings. We’re the local crew that shows up with a welding rig and a truck full of post sleeves, hinge hardware, and operator parts, not a sales binder. If you live in the 19320 ZIP and your gate is sagging, seized, or simply gone, call (877) 610-2993 and you’ll talk to a person who has been doing this work since 2001. Hal Gatewood’s name is on the shop and on every invoice, and we answer the phone 24 hours a day.
Why Gatewood Fence & Gate Is Coatesville’s Preferred Gate Installation Company
Coatesville isn’t like the newer subdivisions you pass along Route 30. The housing stock here was built around the steel mill era, and the gates we see reflect that. We understand the difference between an ornamental iron swing gate from 1920 and an aluminum prefab panel from five years ago, and we install both. When a rowhouse off Lincoln Highway has a pedestrian gate hanging from a brick pier that’s shedding mortar, we know the post itself isn’t the only thing that needs attention. That’s local knowledge you can’t get from a national outfit.
We’ve worked behind homes near the Brandywine Creek, around mill-worker cottages off East Lincoln Highway, and on corner lots with original iron fencing throughout the city. Our customers in Coatesville call us back because the job gets done and the price we quote over the phone is the price on the invoice. Every installation carries the 90-Day Done Right Promise in writing. The person who shows up is background-checked and uniformed, and Hal has been at this since 2001 with a published address and license number anyone can verify.
When you call, a live person answers. Not a voicemail, not a call center three states away. We schedule work in Coatesville directly and we show up when we say we will. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Our Gate Installation Services in Coatesville
Driveway Gate
A driveway gate in Coatesville usually means working with a narrow side yard or an alley opening that was measured decades ago. We measure in person, check the setback from the street, and spec the gate and opener for the actual opening. Most driveway gate installations here are double swing gates or single sliding panels on corner lots where a swinging gate would block the sidewalk.
Pedestrian Gate
Pedestrian gates in Coatesville are often original ironwork hung on brick pillars that have seen a hundred freeze-thaw cycles. We check the hinge post first, because a gate sags in the post, not in the middle. When the masonry has failed, we core out the old material, set a galvanized post footing, and re-hang the gate properly. Then the latch aligns, the lock works, and the gate doesn’t drag on the walkway.
Sliding Gate
Sliding gates make sense on Coatesville lots where there’s enough fence line to roll the gate back. Many of the alley-facing lots behind rowhouses don’t have that space, but corner properties and wider parcels often do. We install the track, rollers, and operator, and we check the ground slope. A sliding gate that fights the grade will burn out a motor in two winters.
Swing Gate
Swing gates are the most common installation in Coatesville, and the most common failure point is the post. Original iron swing gates hung on shallow footings heave out of plumb every spring. We set new footings below frost line when the old concrete is too thin, then re-hang the gate with modern hinges and safety photocells. The gate looks original when we’re done, but it operates like it should.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Coatesville
We’re certified to service nine major gate brands, and we stock parts for the ones most common in Coatesville: Viking, DoorKing, and Elite among them. If you have an old Viking operator that’s still running but needs a new limit switch, we carry it. If your DoorKing control board has failed, we replace it with the correct model, not a generic substitute. For Coatesville customers, that means faster turnaround because the part is already on the truck. We also install Ghost Controls openers on retrofitted swing gates where a solar option makes sense for an alley with no power run.
Common Gate Installation Problems We See in Coatesville Homes
- Spalled brick pillars with no solid hinge anchor. In the 19320 ZIP, many gate posts are set into early-1900s brick pillars where the mortar joints have crumbled. The hinge hardware has nothing to bite into, and the gate sags no matter how many times you adjust the panel. We core out the old masonry and set a new galvanized footing.
- Seasonal heaving from the freeze-thaw cycle. Chester County winters repeatedly cross the freezing mark, and shallow concrete footings shift every year. Gates that worked fine in October are binding by March. We dig deeper and set footings below frost line so the gate stays plumb.
- Rusted hinge pins seized inside old wrought-iron barrels. Pre-World War II iron gates in Coatesville often have hinge pins that have rusted solid. The operator overworks, trips the overload, and eventually fails. We drill out and replace the pins, or rebuild the hinge entirely if the barrel is too far gone.
- Legacy operators installed before modern safety requirements. Many older Coatesville gates have openers that predate current safety standards for photoelectric sensors and reverse sensitivity. We can often retrofit a new control board and photocells onto the existing mechanical drive, which costs less than a full replacement.
Pricing for Gate Installation in Coatesville, PA
A single pedestrian gate installation in Coatesville typically runs $1,200 to $2,800, including posts and hardware. A single swing driveway gate with a Viking or Ghost Controls operator runs $3,500 to $6,500 depending on gate width, post condition, and whether we’re setting new footings. A sliding gate with track and operator runs $4,000 to $7,500 on most residential lots. If your brick pillars need to be cored and rebuilt, add $400 to $900 per pillar depending on access. Every price is quoted and agreed in writing before any work starts. We don’t change the number at the door. Call (877) 610-2993 for a free estimate, and ask about the $40 off any repair over $200 and the 10% discount for seniors and veterans.
We Also Serve Cities Near Coatesville
Our Gate Installation team covers Coatesville and the surrounding communities, and we’re often on jobs in Downingtown, Chester Springs, New Holland, and Lionville the same week. If you’re just outside Coatesville but still in Chester County, give us a call. We schedule the same way we do everywhere: free estimate, upfront price, and a job done right. For the full scope of what we do locally, see Gate Installation in Coatesville.
Serving Coatesville, PA - Our Local Coverage Area
We’re based in the Coatesville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Coatesville
We remove the failed mortar and any loose brick from the pillar, then core out the center to accept a galvanized steel post sleeve set in new concrete below frost line. The sleeve gives the hinge post a solid, continuous anchor. We then rebuild the brick face around the sleeve so the pillar looks original but the gate actually holds. Call (877) 610-2993 to have a brick pier inspected.
Yes, in most cases. The iron panel itself is usually sound; the problem is the hinge pins, the post anchor, and the absence of any modern safety controls. We re-hang the original gate on new hinges and a new post sleeve, then install a Ghost Controls or Viking operator with photocells and reverse sensitivity. You keep the period look and get a gate that meets current safety practice. Call (877) 610-2993 and we’ll tell you if your specific gate is a candidate.
Almost never. A gate sags because the hinge post has moved or the hinge hardware is worn. In Coatesville, the usual culprit is a shallow footing heaving through the freeze-thaw cycle, or a brick pier that has lost its mortar bond. We fix the post first, then re-hang the panel. Adjusting the panel alone means you’ll fix it again next spring. Call (877) 610-2993 for a free assessment.
If the gate opens automatically or by remote, yes. A loop detector is what tells the gate a car is waiting, and it also prevents the gate from closing on a vehicle. On narrow alley lots where a driver can’t back up easily, that’s not optional. We install loop detectors as part of every sliding gate automation job in Coatesville. Call (877) 610-2993 to talk through your specific alley layout.
When the control board, limit switches, and drive mechanism all need replacement at the same time, you’re often within a few hundred dollars of a complete new gate and operator. Repairing a 25-year-old operator piece by piece rarely saves money. We’ll show you the numbers for both paths before you decide. No pressure, just the real cost either way. Call (877) 610-2993 for an honest breakdown.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Coatesville since 2001.