Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Boynton Beach
A new gate installation in Boynton Beach typically runs $2,800-$9,500 depending on the gate type, material, and whether you’re in an eastern coastal neighborhood or a western HOA community. Most single driveway gate installs take one to two days on site, with permitting and material lead time adding a week or two before we start digging. If you’re dealing with a gate that’s sagging, rusted through, or simply too far gone for Gate Repair - Boynton Beach, call us at (877) 610-2993 and Hal will tell you straight whether it’s fixable or time to replace it.
We work across Boynton Beach every week, from the Intracoastal-adjacent streets around 33435 to the big master-planned communities west of Florida’s Turnpike. We know the difference between a 1960s ornamental iron driveway gate on Federal Highway and a multi-lane HOA slide gate in Valencia Reserve, and we spec hardware accordingly.
Why Gatewood Fence & Gate Is Boynton Beach’s Preferred Gate Installation Company
Hal Gatewood has been at this since 2001, and his name is on the shop and on every invoice. That matters in Boynton Beach, where a lot of gate work happens through HOA boards and property managers who need a contractor they can hold accountable. We publish our address, we answer the phone with a live person around the clock, and when a gate fails at a community entrance at 6 a.m., someone picks up on the first ring.
Our crew works Boynton Beach regularly, so we’re not learning your streets from a GPS. We know that the western ZIP codes run on reserve-fund approval cycles, that the eastern neighborhoods fight salt corrosion, and that Palm Beach County wind-load code applies to every vehicular gate we install. Every job, whether it’s a driveway gate off Hypoluxo Road or a pedestrian gate at a Kings Point amenity pool, carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back. No runaround.
We also bring an on-site welding rig to most installations for Gate Parts & Welding - Boynton Beach. That means we don’t haul your gate to some shop across the county and leave your driveway open for three days. We weld, set posts, and hang panels right where the gate lives. For Boynton Beach homes and HOAs, that’s the difference between an install that fits the first time and one that needs “adjustments” for the next six months.
Our Gate Installation Services in Boynton Beach
Sliding Gate Installation
Sliding gates are the workhorse of Boynton Beach’s western HOA communities. Every 55+ development from Valencia Bay to Valencia Cove runs large-format vehicular slide gates, and a new install means more than hanging a panel. You need proper cantilever or V-track hardware, a correctly sized operator, loop detectors, safety photocells, and in many cases coordination with the board’s reserve-fund schedule. We install and replace all of it, and we spec marine-grade fasteners on every exterior connection because the salt air doesn’t stop at Military Trail.
Swing Gate Installation
Swing gates are common on eastern Boynton Beach properties, where 1960s-1980s homes often have original ornamental iron driveway gates that have spent decades in coastal humidity. A new swing gate in Boynton Beach needs hinge posts set in concrete with stainless anchors, not the galvanized bolts that corrode to dust within five to seven years near the Intracoastal. We also check the post footings before we hang anything, because a gate sags in the hinge post, not in the middle, and that’s where we start.
Double Gate Installation
Double swing gates show up on wide driveways throughout Boynton Beach, from older ranch-style homes east of I-95 to estate lots in the western acreage. The tricky part with double gates is the center alignment, especially on clay soils that shift seasonally. We set the posts deep, use stainless hardware throughout, and align both leaves so they meet cleanly without binding, even after a wet Palm Beach County summer.
Pedestrian Gate Installation
Pedestrian gates in Boynton Beach often serve HOA amenity areas, pool enclosures, and side-yard access points. These get less attention than vehicular gates, but they fail the same way: salt air eats the hinges, the latch binds, and the post starts leaning. We install pedestrian gates with stainless hinges and latches sized for coastal exposure, and we can tie them into existing Boynton Beach Gate Access Control if your community uses keypads or fobs.
For a broader look at what we do, see our Gate Installation service page. This page is about what Boynton Beach specifically needs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Boynton Beach
We’re certified to work on nine major gate brands, and we stock parts for the ones you’re most likely to see around Boynton Beach: FAAC, BFT, Linear, and Viking. These dominate the HOA slide gate market in the western communities, and we keep common boards, loop detectors, and safety edge parts on hand so we’re not waiting on a distributor in Fort Lauderdale while your entrance sits open. Whether you need a new FAAC operator on a community gate or a BFT control board swap on a driveway slider, we handle it.
Common Gate Installation Problems We See in Boynton Beach Homes
- Salt-corrosion of hinge posts and fasteners: In the eastern ZIP codes (33435, 33426), salt-laden air off the Atlantic and Intracoastal eats standard galvanized hardware in five to seven years. We see hinge posts rotted at the base and operators with enclosures rusted through, and the fix is marine-grade stainless, not another coat of paint.
- Loop detector failures at HOA entrances: The western communities sit on saturated clay, and South Florida’s summer downpours degrade underground vehicle loop wire insulation within five to eight years. The gate goes intermittent, the board thinks the operator is dead, and it’s actually a loop fault. We replace loops and re-tune the detector so the gate stops ghosting.
- Non-compliant wind-load installations: Palm Beach County requires vehicular gates to meet hurricane-rated or breakaway standards. We find older gates around Boynton Beach that were installed without permits or with undersized posts, and they fail inspection when the HOA refinances or the homeowner sells. We bring new installs up to code from the start.
- Undersized operators on large HOA slide gates: A residential-grade opener can’t push a 30-foot community slide gate day after day, but we see exactly that in some Boynton Beach developments where the original builder cut corners. We size operators to the gate’s weight and duty cycle, or the new gate burns out the motor within a year.
Pricing for Gate Installation in Boynton Beach, FL
Here’s what Boynton Beach homeowners and HOA boards can expect for common gate installations:
- Single driveway swing gate (standard steel or aluminum): $2,800-$4,500 installed, including posts, hinges, and basic operator.
- Sliding driveway gate: $3,500-$6,500 depending on length, material, and operator type. Cantilever designs run higher than V-track.
- Double driveway gate: $5,000-$9,500 installed, with alignment, dual-lead hardware, and paired or single operator.
- HOA community slide gate (multi-lane): $8,000-$25,000+, depending on lane count, panel material, access control integration, and loop/photocell requirements.
- Pedestrian gate: $800-$2,400 installed, more if tied into existing access control.
These ranges reflect Boynton Beach’s specific market: coastal hardware upgrades, wind-load compliance, and HOA coordination all factor in. We quote the price before any work starts, in writing, and that’s the price you pay. No surprise invoice at the door. Call (877) 610-2993 for a free estimate, and remember we offer $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Boynton Beach
Our crews work Boynton Beach every week, and we also cover Lantana, Delray Beach, Kings Point, and Lake Worth. If you’re on the edge of Boynton Beach or just over a city line, call us and we’ll tell you straight whether we can get to you. You can also see our Gate Installation in Boynton Beach coverage details, or our main Gate Installation service page for the full scope of what we do.
Serving Boynton Beach, FL - Our Local Coverage Area
We’re based in the Boynton Beach area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Boynton Beach
Loop detectors fail because South Florida’s saturated clay soils and intense summer rain degrade the underground wire insulation within five to eight years, and Boynton Beach’s western HOA belt has dozens of communities built in the same 2000s-2010s window with the same loop infrastructure, so failures cluster by neighborhood age. When the loop shorts, the gate ignores cars, stays open, or cycles erratically. The fix is replacing the loop wire and re-tuning the detector, not swapping an operator that’s still good. Call (877) 610-2993 if your community gate is acting up, and we’ll diagnose it on site.
Yes, it does. In the eastern ZIP codes (33435, 33426), salt-laden air off the Atlantic and Intracoastal corrodes standard galvanized hinge posts, bolts, and operator enclosures within five to seven years. We install gates in coastal Boynton Beach with marine-grade stainless steel fasteners, stainless hinge hardware, and powder-coated or aluminum panels rated for salt exposure. Skipping that spec saves a few hundred dollars up front and costs a full replacement in under a decade. Call (877) 610-2993 and we’ll quote the right hardware for your specific location.
Usually yes. If the gate panel and posts are structurally sound, we can install a new FAAC, BFT, Viking, or Linear operator, swap the safety photocells and loop detectors, and bring the whole system up to Palm Beach County wind-load standards without replacing the panel. If the panel is rusted, the post footing is compromised, or the rack is worn, we’ll tell you honestly and show you where the gate is failing. We don’t sell replacements for gates that still have years left. Call (877) 610-2993 for an honest assessment.
Palm Beach County requires vehicular gates to meet hurricane-rated or breakaway design standards, which means the post footings, panel construction, and hardware all have to be spec’d to withstand storm-force winds or designed to release without turning into a missile. A non-compliant gate can fail inspection, delay a home sale, or leave your entrance inoperative right when you need it closed. We pull permits on every new gate installation in Boynton Beach and install to code from day one. Call (877) 610-2993 with questions.
We work directly with HOA boards and property managers throughout Boynton Beach’s western communities, and we know how reserve-fund approval cycles work. We provide written quotes with line-item pricing, we attend board meetings when asked, and we schedule installation around your community’s approval window. At Valencia Reserve off Boynton Beach Boulevard, our crew replaced a sagging double swing gate at the main entrance after the hinge post had corroded at its base from years of salt drift off the Intracoastal. We set new stainless post footings, swapped the rusted rack and pinion on both gate operators, and installed fresh loop detectors and safety photocells before the board’s reserve-fund approval window closed. That’s the kind of coordination we handle routinely. Call (877) 610-2993 to get a quote started for your community.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Boynton Beach since 2001.