Gate Repair in Tiburon - Same-Day Repair, Priced Before We Start

Gate Repair in Tiburon, CA

A gate that won’t open in Tiburon usually comes down to one of three things: a motor housing corroded by bay air, a hinge worn past its useful life, or a control board that got damp one too many times. We fix all three, most often the same day you call. The marine air on this peninsula is harder on gate hardware than almost anywhere else in Marin, and the crews at Gatewood Fence & Gate have been working in that environment long enough to know exactly where each brand fails and why. Call (877) 610-2993 and a live person picks up, 24/7.

Call (877) 610-2993

Why Tiburon Homes Are Different

Tiburon sits on a narrow peninsula with San Francisco Bay on three sides, and that geography shapes every gate repair we do. The salt-laden marine air works into motor housings, hinge pins, and control boards far sooner than a manufacturer’s inland rating would suggest. Add the afternoon thermal winds that blow off the water and the overnight fog that condenses on every metal surface, and you get hinges that wallow out, arms that fatigue, and boards that short.

The housing stock compounds things. Most Tiburon properties are mid-century hillside ranches and newer custom estates with long driveways on a grade. A gate operator on a slope works harder than the same unit on flat ground, and when power cuts, a swing gate can drift downhill if the limit switches were never calibrated for that pitch. Homes off Paradise Drive, in Belveron, and up from Main Street all face their own version of the same challenge: beautiful views, brutal conditions for metal.

Gate Repair in Tiburon

Gate repair in Tiburon typically runs between $185 and $1,400 depending on whether we’re tightening a hinge pin or rebuilding a salt-corroded operator. Most jobs are finished the same day or next morning, and the person who answers the phone at (877) 610-2993 is connected to the crew that actually shows up. We know Tiburon driveways, Tiburon wind patterns, and Tiburon salt, and we repair before we replace, a philosophy you won’t get from a company that wants to sell you a new gate. This is what we do most often.

Electric Gate Repair

Automated gates in Tiburon work harder than almost anywhere else in the Bay Area. Salt fog condenses on motor housings overnight, and the thermal wind off the Bay pushes against the gate arm every afternoon. We rebuild controllers, replace corroded wiring, and recalibrate openers so they stop throwing error codes. If your gate hums but won’t move, that’s usually a capacitor or limit switch issue, not a reason to replace the whole operator. Electric gate repair, including control board work, runs $320 to $850 in Tiburon depending on the fault, and we stock parts for FAAC, BFT, Linear, and Viking units because those are the brands most common on local estates.

Automatic Gate Repair

An automatic gate on a sloped Tiburon driveway has to be dialed in. Torque settings, limit switches, and obstruction sensitivity all need to account for grade. When a gate was installed with flatland assumptions, it drifts downhill after a power outage or reverses for no reason. We recalibrate to your specific slope and gate weight. The fix is usually under $300, which is a fraction of what a bumper replacement costs when a gate free-swings into a car on a dead battery.

Hinge & Post Repair

A gate sags in the hinge post, not in the middle. That’s the first thing we check on ornamental Tiburon gates because the post is where daily wind stress and salt corrosion do their worst. We rebuild hinge points with epoxy-set anchors where the footing has loosened, and we replace rusted hinge pins with salt-hardened stainless or sealed alternatives. Full hinge post rebuilding runs $700 to $1,400 on steep lots where we’re working on a slope. You don’t need a new gate. You need a post that isn’t moving.

Gate Realignment

When a heavy custom gate scrapes the driveway or won’t latch, the fix is usually realignment, not replacement. We level the gate, shim the hinges, and reset the latch so it closes cleanly. On hillside properties, this also means checking the operator’s torque setting so the motor isn’t fighting gravity more than it should. Realigning a heavy ornamental gate costs between $275 and $600 depending on weight and access, and a properly aligned gate extends the life of both the panel and the opener. This is the core of our Gate Repair work in Tiburon.

How much does gate repair cost in Tiburon?

Most gate repairs in Tiburon run between $185 and $1,400, depending on whether we’re replacing a hinge pin or rebuilding a salt-corroded operator on a steep driveway. Control board replacements typically land between $320 and $850. Every price is quoted and agreed before work starts. Call (877) 610-2993 for an exact number for your gate, and remember estimates are free.

Can you come today if my gate won’t open?

In most Tiburon cases, yes, same-day service is available when you call before early afternoon, and next-morning is typical for late-day calls. We answer the phone live around the clock, so call (877) 610-2993 the moment the gate fails. We’ll tell you what it likely is, what it likely costs, and when the person in the truck will be there.

Gate Installation in Tiburon

Gate installation in Tiburon starts with the driveway, not the gate. The slope, the exposure to bay wind, and whether a swing gate will arc into the street or a hillside all shape which design actually works. We measure on site, write a price, and never start until that number is agreed. A full installation ranges from $1,800 to $6,500 depending on materials, gate size, and whether we’re running new power and safety edges, and we provide a written quote before anything is ordered. This is the work that backs our Gate Installation hub.

Custom Gate Installation

Most Tiburon properties call for a custom gate, not an off-the-shelf panel, because the driveway is steep or the opening isn’t standard. We work with local fabricators who know the marine environment and specify salt-hardened hardware from the first bolt. Custom installations typically run $3,200 to $6,500. Every gate is matched to the grade it has to hold, and Hal checks the final install personally.

Slide Gate Installation

On narrow hillside driveways, a slide gate is often the only design that works because a swing gate would arc into the hillside or the road. Slide installations in Tiburon typically run $2,800 to $5,800 depending on track length and motor size. We set the rack and pinion to handle the daily thermal wind load, so the gate doesn’t bind on salt-roughened rails a year in.

How much does a full gate installation cost on a sloped Tiburon driveway?

Expect $2,800 to $6,500 for a full gate installation in Tiburon when the driveway is on a grade, with custom ornamental work at the upper end. Slope, gate weight, power run, and whether we’re adding a slide track versus swing hinges all move the number. You’ll get a written quote itemizing each part before anything is ordered.

Do you handle the power run for a new gate in Tiburon?

Yes. We run conduit and wire from the house to the gate, including under driveways and through hillside landscaping where needed, and we install dedicated circuit protection. For Tiburon properties with long, winding driveways, the power run can add meaningfully to the total price, and we’ll show you exactly how much before we dig.

Gate Motor & Opener in Tiburon

Gate motor and opener repair in Tiburon typically runs between $225 and $680, depending on whether we’re replacing a circuit board, a full operator, or adding a battery backup to an existing system. Most calls get same-day or next-morning service, and we carry parts for FAAC, BFT, Linear, and Viking operators so you’re not waiting a week for a board to ship. If your gate is grinding, drifting downhill, or dead at the keypad, call (877) 610-2993 and we’ll diagnose it over the phone. See the full scope on our Gate Motor & Opener page.

Motor Installation

New motor installation in Tiburon means matching the operator to the gate’s weight, the driveway’s slope, and the salt exposure. A hillside property off Tiburon Boulevard needs different calibration than a flat lot in the flats near Blackie’s Pasture. Full motor and operator replacement usually lands between $550 and $1,800 depending on gate size and whether we’re adding battery backup, and every install carries the 90-Day Done Right Promise in writing.

Motor Repair

Most Tiburon motor failures trace to one of three things: corrosion on the control board from marine air, a worn capacitor from daily thermal wind cycles, or stripped gear teeth from years of fighting a sagging gate. We diagnose the actual fault before replacing anything. A typical control board replacement runs $225 to $480 including the board and labor. If the post has shifted and the arm is bent, we fix the post first because a new motor on a bad post fails the same way in half the time.

Slide Motor Repair

Slide motors on Tiburon properties fail at the rack and pinion first because the daily wind pushes the gate and the constant load wears the pinion teeth unevenly. We replace rack sections, rebuild worn pinions, and set the torque limits so the gate stops pushing the instant it meets resistance. Slide motor rebuilds, including rack and pinion repair, typically run $400 to $900. A slide gate that jerks and grinds near the end of its travel is telling you something, and we can hear it.

Why does my Tiburon swing gate drift downhill after a power outage?

Because the limit switches and torque settings were never calibrated for the grade, or the calibration has drifted over years of use. On sloped Tiburon driveways, a mis-calibrated gate swings free downhill when utility power drops. The fix is recalibration for the actual slope, usually with a battery backup added. Call (877) 610-2993 for an estimate, which is free.

Can I keep my original FAAC gate motor and just replace the control board?

Often yes, if the motor windings test sound and the gate itself isn’t sagging. We can fit a modern compliant board with entrapment protection to many older FAAC, BFT, and Viking motors, which typically runs $225 to $480. If the board predates UL 325 and no compliant retrofit exists, replacement is the only legal option. We’ll tell you straight which path applies to your gate.

Gate Access Control in Tiburon

Gate access control in Tiburon usually comes down to one of two calls: either a keypad stopped reading codes after a foggy week, or a homeowner wants video intercom added to a gate that only ever had a remote. We handle both, and everything in between. Salt air is the common thread on this peninsula, and we install access hardware rated for coastal exposure, not the same units that fail in San Rafael. This is the work covered in depth on our Gate Access Control hub.

Keypad Entry

Keypads fail in Tiburon more often than any other access component, and it’s almost always salt corrosion. The marine air works into the keypad housing, shorts the control board, and then codes stop registering. We replace the internals with sealed, corrosion-resistant components rather than swapping in another unit that’ll die the same way in two years. Keypad repair or replacement in Tiburon typically runs $180 to $450 depending on whether it’s a standalone unit or tied into a video intercom system.

Video Intercom

Video intercom is the most requested upgrade we install in Tiburon. People want to see who is at the gate before opening it, especially on properties set back from the road or hidden below the street on a hillside lot. We integrate video intercom with existing FAAC, BFT, Linear, and Viking operators, using sealed connections and coastal-rated control boxes. A video intercom added to an existing Tiburon gate typically runs $1,200 to $3,500 complete.

Smart Access

Smart access means controlling the gate from your phone, whether that’s app-based unlocking, visitor codes that expire, or geofenced auto-open when you pull up. On Tiburon hillside lots, that’s a real safety benefit because you can open the gate from the bottom of the driveway instead of stopping on the steep part to punch a code. Smart access retrofits start around $800 on a typical Tiburon gate, and we program everything on site while you watch.

Why does my Tiburon keypad fail after heavy fog?

Condensation. Overnight fog settles on the keypad surface, seeps past the gasket, and shorts the membrane or board inside. Once that happens, codes stop registering. We install sealed keypads with drainage channels, and on bay-facing lots we’ll add a small weather hood to keep moisture off the face entirely. That five-minute upgrade saves the $180 to $450 cost of replacing another unit.

Can I add a video intercom to my existing Tiburon gate system?

Yes, in most cases. We add video intercom to existing FAAC, BFT, Linear, and Viking systems regularly, with two-way audio, video, and remote unlocking from your phone. A full retrofit on a Tiburon property usually runs $1,200 to $3,500 depending on driveway length and wiring path. Call (877) 610-2993 and we’ll give you a written number for your specific gate.

Gate Parts & Welding in Tiburon

Gate parts and welding in Tiburon usually means one of three jobs: a hinge that salt air has seized, a post that has shifted on a hillside, or a rail that has cracked at the weld. We handle all three on site, in your driveway, with the gate staying put. The 94920 peninsula presents a corrosion problem you won’t find a few miles inland, and on-site welding is the heart of our repair-first approach. That’s the work documented on our Gate Parts & Welding page.

Hinge Replacement

Hinge pins in Tiburon corrode faster than in San Rafael or Novato because the bay air works on them from three sides. A stiff gate is not a nuisance; it’s a warning that the pin is about to seize or snap. We replace the pin, sleeve, and cap with corrosion-resistant alloys, then test the swing with the operator disconnected so we know exactly what the motor is fighting. Most hinge replacements in Tiburon run $220 to $480 per hinge depending on size and whether the post needs reinforcement.

Rail & Post Welding

Wrought iron and aluminum rails crack at the welds on long swing gates, especially along wind-exposed stretches like Paradise Drive where afternoon thermal winds rock the gate daily. A hairline crack is a future snap. We grind it back, reweld it, and add a small gusset when the design allows, keeping the gate’s original look instead of a new panel. Rail welding in Tiburon runs $180 to $420 per rail, and post replacement runs $450 to $1,100 per post on hillside lots where access is tight.

Custom Welding

Some Tiburon gates are one-off designs from a fabricator who retired years ago. When a piece of scrollwork breaks, ordering a replacement isn’t an option. Hal welds new sections to match the existing pattern, in place, on the gate, in your driveway. We also build mounting plates for operators, reinforcements for wide panels, and brackets for intercoms or keypads the gate was never designed to carry. Custom welding is quoted per job after we see the metal, usually $150 to $600 depending on complexity.

Why do gate hinge pins in Tiburon corrode faster than in San Rafael?

Tiburon sits on a narrow peninsula with the Bay on three sides, so the air is loaded with salt and marine moisture. That salt-saturated air attacks the hinge pin-to-sleeve gap year-round, while overnight fog condenses on the metal and holds the salt in place. The fix is corrosion-resistant pin and sleeve materials, not another coat of paint. Call (877) 610-2993 and we’ll tell you what your specific hinges need.

Can you weld a broken ornamental rail on a steep Tiburon driveway?

Yes. We weld on site, even on a steep grade, setting up on the slope and grinding back the crack before rewelding the rail. If you’re on Paradise Drive or another windy stretch, ask about adding a reinforcement gusset so the same crack doesn’t come back. Rail welding runs $180 to $420 per rail, and the gate never leaves your driveway.

Brands We Service in Tiburon

We service FAAC, BFT, Linear, and Viking operators extensively across Tiburon, plus LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. We carry common repair parts locally for these brands, so most board swaps and motor repairs happen same-day or next-morning without waiting on a ground shipment. See the full list on our brands page.

Pricing for Gate Repair in Tiburon, CA

Neighborhoods We Serve in Tiburon

We work all over the 94920 zip code, from the hills above Main Street to the cul-de-sacs off Paradise Drive. Typical response time in Tiburon is same-day or next-morning for most repairs, depending on what the gate needs and when you call.

• Belveron
• Paradise Drive
• Reed Ranch Road area
• Marinero Ridge
• Point Tiburon

Service Area - Cities Near Tiburon

Beyond Tiburon, CA, our crews regularly work across the surrounding Marin peninsula: Sausalito, CA to the south, Tamalpais-Homestead Valley, CA and Tamalpais Valley, CA just over the ridge, and Corte Madera, CA and Mill Valley, CA to the north. If your gate is anywhere on the peninsula, call and we’ll be straight about whether we cover it.

FAQs About Gate Repair in Tiburon