Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Scarsdale, NY
Gate repair in Scarsdale typically runs $225-$850 for most hinge, post, and realignment work, with electric and automation jobs landing between $350 and $2,400 depending on the operator and scope. We’re at (877) 610-2993 around the clock, and the person who picks up is a real person, not a queue. Scarsdale isn’t the place for a generic gate company - the village’s concentration of 1920s-1950s Tudor Revival and Colonial estate homes means nearly every call involves custom ornamental wrought iron hung on original mortared stone or brick pillars, not standard panels you can order from a catalog.
Why Scarsdale Homes Are Different
Scarsdale’s housing stock is dominated by large-lot estate homes built between roughly 1910 and 1955, most with formal entry gates featuring stone or brick pillar posts original to the property. These aged pillars and period ironwork require matching fabrication skills and masonry coordination that standard residential gate work does not.
Westchester County experiences frequent freeze-thaw cycling through winter rather than sustained deep freezes, which repeatedly heaves gate post footings and cracks mortar joints in stone pillars. That’s the leading cause of gate sag and hinge binding in Scarsdale’s older estate gates. Spring is peak season as homeowners discover winter-induced misalignment after the ground settles.
Then there’s the Architectural Review Board. Scarsdale’s ARB must approve any exterior alteration that changes appearance, so even replacing a broken gate section can require village sign-off that neighboring White Plains or Yonkers would never demand. We check compatibility before starting and submit ARB paperwork when your project needs it.
Gate Repair in Scarsdale
Gate repair in Scarsdale is rarely a single-fix job. The 80-year-old stone pillar a wrought iron gate hangs from has usually heaved or lost mortar, meaning a mason must stabilize the post before any gate adjustment will hold through the next winter. We coordinate both trades - masonry and gate work - so you’re not calling someone else in six months when the gate sags again. Gate Repair is what we’ve built this shop on since 2001.
Hinge & Post Repair
In Scarsdale, the hinge is rarely the only problem. The post it’s bolted to has usually heaved, cracked, or lost mortar after decades of freeze-thaw cycling. We fix both: weld or re-hang the hinge, then stabilize the stone or brick pillar so the repair survives next winter. On Heathcote Road we reset a drifted wrought iron swing gate that had sagged three inches at the latch after a freeze-thaw cycle heaved its original 1927 stone pillar. Hinge, post, and realignment work in Scarsdale runs $225-$650, depending on whether we’re resetting a single hinge or stabilizing a heaved stone pillar.
Gate Realignment
A gate sags in the hinge post, not in the middle, and that’s where we start. Scarsdale’s freeze-thaw winters raise and lower the ground by fractions of an inch every single year. That repeated movement is why you adjust a gate in October and it’s binding again by April. Realignment means more than twisting a bolt: we check the post plumb, check the footing, and set the gate so it clears the latch even after the ground shifts. Spring is our busiest season for exactly this reason. Weld and rust repair on ornamental iron runs $180-$500 per section, including on-site fabrication and matching to the existing pattern.
Electric Gate Repair
When a LiftMaster or Ghost Controls opener starts clicking without moving, or the gate stops halfway and reverses, the culprit is usually a failing capacitor, a corroded limit switch, or a control board on its last legs. We diagnose on site, and we stock parts for the brands you’re likely to find on Scarsdale properties: Viking, DoorKing, Elite, FAAC, BFT, Linear, Ghost Controls, Mighty Mule, and LiftMaster. No guesswork, no “we’ll order it and get back to you.” Electric gate diagnosis and minor component replacement in Scarsdale runs $175-$450 for capacitors, limit switches, photocells, and board-level repairs.
Why does my estate gate sag every spring even though we adjusted it last fall?
Freeze-thaw cycles heave the ground under the hinge post. Scarsdale winters hover just below freezing rather than staying deeply frozen, so the ground thaws and refreezes dozens of times. Each cycle moves the post a fraction of an inch. By spring, the gate has drifted far enough to bind at the latch. The permanent fix is stabilizing the post footing and mortar, then re-hanging the gate, not just cranking the hinge bolt again. Call (877) 610-2993 and we’ll assess whether your post needs masonry work before any realignment will hold.
Will I need Scarsdale ARB approval to repair my existing ornamental gate?
Only if the repair changes the gate’s appearance. Replacing a rusted iron section with a matching fabrication can require Architectural Review Board approval, as can painting the gate a different color or altering its profile. A hinge repair, operator swap, or realignment that keeps the existing look typically does not. We check compatibility before starting and submit the ARB paperwork if your project needs it, so you’re never exposed to a stop-work order after the fact.
Gate Installation in Scarsdale
Gate installation in Scarsdale usually means working with original 1920s-to-1950s estate hardware, not swapping in a generic panel. It starts with getting the post solid, because a gate sags in the hinge post, not in the middle. Hal will spend time checking how true the posts are before any new gate goes on. Gate Installation is measured, ordered, and scheduled - never rushed.
Driveway Gate
A driveway gate on a Scarsdale property is usually the widest, heaviest iron on the lot, often hung on original pillars laid before the Second World War. We build and hang custom driveway gates to match the estate’s original ironwork, whether that’s a simple Colonial picket or ornamental work with scrolls that a fabricator has to hand-forge to match. A single custom driveway gate in Scarsdale generally runs $6,000-$12,000, and a double driveway gate or sliding gate with new posts and footings lands between $10,000 and $18,000.
Pedestrian Gate
Pedestrian gates in Scarsdale see more cycles than driveway gates because they’re the gate the kids, the landscaper, and the mail carrier actually use every day. We fabricate and hang pedestrian gates that match the driveway gate or stand on their own, always sized to the existing stone or brick opening. Many of the ones we replace were hung as afterthoughts years ago, and the tell is paint worn through on the latch side from fighting a post that drifted. A pedestrian gate installation in Scarsdale typically runs $2,800-$6,500 for custom iron, installed, with matching hardware.
Sliding Gate
Sliding gates make sense on Scarsdale properties where the driveway rises steeply from the street or where a swing arc would cross a walkway. We install track or cantilever sliding gates with motor and operator work handled by our Gate Motor & Opener crew. The ground movement in Westchester means the track bed has to be overbuilt from the start: a slab that’s too thin will heave, and the gate will bind by February. If existing stone pillars need masonry stabilization before hanging, that adds $1,200-$4,000 depending on how much mortar work the mason has to do.
Can you install a gate that matches my original 1920s iron?
Yes, and that’s most of what we do in Scarsdale. Hal will look at the existing panels, measure the pickets, match the scroll pattern as closely as the original allows, and weld the new section on site so the fabricator never takes the gate out of your driveway. The goal is a gate that looks like it’s been there since the house was built, not a shiny new panel that screams replacement.
Does a new automated gate cost more in Scarsdale than in nearby towns?
Material and labor are comparable across Westchester, but Scarsdale jobs sometimes carry a slight premium because of the pillar work and the ARB paperwork, not because anyone is padding the invoice. A double driveway gate that would cost $10,000 in Tuckahoe might be $11,500 in Scarsdale if the original stone posts need heavy repointing. We’ll always break that out line by line before you agree to anything.
Gate Motor & Opener in Scarsdale
A dead gate motor in Scarsdale doesn’t just trap your car in the driveway. It leaves a wide opening onto Post Road, Heathcote Road, or any of the quiet estate lanes where a stalled gate reads as an invitation. Most calls we get start the same way: the opener hums but nothing moves, or the gate stops three feet short and refuses to budge. That’s usually a capacitor, a limit switch, or a gearbox that’s been quietly failing. Gate Motor & Opener service includes diagnosis, repair, and full replacement when the unit is truly done.
Motor Repair
Scarsdale’s older estate gates often run on openers installed 15 or 20 years ago, and most failures are repairable. A humming motor that won’t turn typically means a failed start capacitor, and we usually have the right one on the truck for FAAC, BFT, Viking, and Linear models. A gate that opens but won’t close often points to photo-eye alignment or a limit switch that’s drifted out of position. Capacitor replacement in Scarsdale runs $180-$320, and limit switch replacement runs $260-$430.
Motor Installation
When the existing opener is genuinely dead and parts are no longer available, we install new motors on your existing gate. Scarsdale’s ARB rules mean we can’t just hang any black box on a period iron gate and call it done. For estate gates with custom wrought iron and stone pillars, we place the motor to stay visually discreet: hidden mounting brackets, conduit runs that follow the masonry, and operators sized for the gate’s actual weight and swing. Full motor replacement on a standard swing gate in Scarsdale runs $1,900-$3,400, and a Linear ram arm installed on an existing gate runs $1,600-$2,800.
Intercom Integration and Battery Backup
A Scarsdale house with a gate at the street and a long drive needs more than a motor that opens and closes. We wire the opener into existing intercom and telephone entry systems, and we add battery backup so the gate still operates during the outages that hit Westchester whenever a nor’easter takes down tree limbs on the local distribution lines. Battery backup sizing depends on the motor’s draw and how often the gate cycles, and we calculate that before quoting anything. Battery backup system installation in Scarsdale runs $850-$1,700.
Is gate work in Scarsdale more expensive than in nearby cities?
Yes. Scarsdale’s gates are older and heavier than typical residential gates in Hartsdale or Tuckahoe, so labor runs longer and materials often include custom fabrication or masonry coordination. A motor replacement on a standard aluminum gate might run $1,600 in a neighboring town; the same job on a period iron gate in Scarsdale often lands between $2,000 and $3,400 because of the gate weight and the need to preserve the original hardware.
Do I need ARB approval before replacing my gate motor in Scarsdale?
That depends on visibility and whether the motor placement changes the exterior appearance. Scarsdale’s Architectural Review Board must sign off on exterior alterations that change appearance, and a new operator with a visible arm or a new conduit run can qualify. We can tell you from photos and a site visit whether your installation likely needs village approval, and we’ll coordinate with the ARB process if it does.
Gate Access Control in Scarsdale
Gate access control in Scarsdale usually means one of three things: a keypad entry for a period estate gate, a video intercom tied to a 1930s stone pillar, or an operator that has been fighting a heaved hinge post since the last thaw. We handle all three the way Scarsdale properties demand - precisely, cleanly, and with the ARB paperwork in mind before we ever touch a chisel. Gate Access Control is about matching the technology to the architecture, not bolting plastic boxes onto historic ironwork.
Keypad Entry
A keypad entry system in Scarsdale typically runs $900 to $2,400 installed, depending on whether we are wiring a hard-line keypad into an existing operator or installing a solar-powered wireless keypad on a remote corner gate. The keypad itself is not the hard part. The hard part is placement: Scarsdale’s Architectural Review Board can treat a visible keypad as an exterior alteration, especially on a 1930s Tudor or Colonial Revival gate. We position keypads discreetly, often recessed into a stone return or mounted on the interior face, and we prepare the filing and photo documentation when village approval is required.
Phone Entry
Phone entry systems are common on Scarsdale properties where the mailbox is 80 feet from the house and visitors do not have a keypad code. We install cellular-based systems that call a house line or mobile app when a visitor presses the call button, and we integrate them with existing operators from Linear, BFT, and Viking. A phone entry install in Scarsdale usually runs $1,500-$3,800 depending on whether we are running cable under a formal walkway or trenching through a hedge line.
Card Reader
Card reader access suits Scarsdale properties with staff, landscapers, or multi-driver households. We install proximity readers at the driveway approach, often paired with vehicle detection loops so a car rolling up does not trigger the reader. Card reader installations in Scarsdale start around $1,100 for a simple standalone setup and climb when we tie into a home automation platform or add encrypted credential management. The cards are weatherproof. The reader is not - so we spec housings that survive Westchester freeze-thaw without condensation killing the board.
Does Scarsdale require ARB approval before replacing a gate access control keypad on an existing estate gate?
Yes, in many cases. Scarsdale’s Architectural Review Board regulates exterior alterations that change the appearance of a property, and a visible keypad mounted on a period gate or a stone pillar falls under that review when it is exposed to public view. A recessed or interior-face keypad often avoids review, but we verify the specific gate and pillar condition before recommending a placement. We prepare the filing and photo documentation when needed.
My gate operator stalls halfway on a heavy custom wrought iron gate - is the problem the board or the post?
Usually the post. A heavy custom wrought iron gate in Scarsdale transfers a lot of lateral load into the hinge post, and an 80-year-old stone pillar that has lost mortar or heaved from freeze-thaw cycling cannot hold a stable hinge axis. The operator board senses the added resistance and trips its force limit. We fix the gate hinges and the post first, then verify the operator programming. When the mechanical problem is solved, the electronics usually behave.
Gate Parts & Welding in Scarsdale
Most of the ornamental iron on Scarsdale estate gates was fabricated before 1960, and no supply house stocks replacement sections that match a 1930s Tudor scroll pattern. That’s why we weld on site, in your driveway, with the gate still hanging in front of us. We match the existing iron, patina the new section to blend, and weld it in place. Gate Parts & Welding is repair-first work: fix the panel without replacing the post, and you’ll fix it twice. Fix the post first, then the panel, and the repair lasts.
On-Site Ornamental Welding
We don’t haul your gate to a shop. We bring the welder to your driveway, match the scrollwork while it’s hanging in front of us, and fabricate replacement sections on site. Wrought iron rusting at the hinge welds is the most common call we get in Scarsdale - the custom scrollwork on a 1930s Tudor gate is not sold at any supply house. Weld and rust repair on ornamental iron runs $180-$500 per section, including on-site fabrication and matching to the existing pattern.
Track and Hardware Repair
Sliding gate track beds in Scarsdale heave every winter from freeze-thaw cycling, and swing gate hinges pull loose from stone pillars that have lost their mortar. We repair rusted or cracked rail sections with on-site welding, replace worn rollers and hinges with hardware that matches the original weight rating, and coordinate masonry stabilization when the post itself is the problem. If the rack is worn or the pinion is slipping on an original sliding gate, we’ll tell you honestly and quote the replacement before touching anything.
Can you match the ornamental ironwork on a 1930s Tudor gate?
Yes. We weld on site so the gate stays in your driveway, and we match the existing scroll pattern while it’s hanging right in front of us. A standard panel off the shelf will never match a custom 1930s Tudor pattern, so we fabricate the section, patina it to blend, and weld it in place. Hal Gatewood has been doing this kind of work since 2001, and the name on the shop is the name on the invoice.
My stone gate pillar has a vertical crack - is that a gate repair or a masonry job?
It’s both, and the gate repair is the part most companies skip. A cracked pillar is a post problem, and the gate hangs on the post. We coordinate the masonry stabilization and then re-hang and realign the gate. Doing the masonry first and the gate second is the only way the repair survives the next winter. We’ll walk you through the whole sequence before any work starts.
Brands We Service in Scarsdale
We stock parts and carry factory training for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common failures - capacitors, limit switches, control boards, gearboxes - are on the truck when we arrive. If we don’t have it, we source it fast through our New York City office and return to finish the job. our brands
Pricing for Gate Repair in Scarsdale, NY
| Service | Typical range in Scarsdale |
|---|---|
| Hinge, post, and realignment work | $225-$650 |
| Weld and rust repair on ornamental iron (per section) | $180-$500 |
| Electric gate diagnosis and minor component replacement | $175-$450 |
| Automatic gate operator replacement | $850-$2,400 |
| Full gate replacement with new posts (custom ornamental iron) | $3,500-$14,000 |
| Pedestrian gate installation (custom iron) | $2,800-$6,500 |
| Single custom driveway gate installation | $6,000-$12,000 |
| Double driveway or sliding gate with new posts | $10,000-$18,000 |
| Masonry stabilization of existing stone pillars | $1,200-$4,000 |
| Capacitor replacement | $180-$320 |
| Limit switch replacement | $260-$430 |
| Full motor replacement (standard swing gate) | $1,900-$3,400 |
What pushes price up in Scarsdale is almost always the masonry: an 80-year-old stone pillar that has heaved or lost mortar adds labor and coordination that a standard post-hole job never needs. Every price is quoted and agreed to before any work starts. You will not get a bigger invoice than the number we discussed. We also take $40 off any repair over $200, there’s no trip charge inside the county, and seniors and veterans receive a permanent 10% discount.
Neighborhoods We Serve in Scarsdale
We work across all of Scarsdale, 10583, from the estate properties off Post Road to the quieter streets in Greenacres and Quaker Ridge. Typical response time for a gate repair call in the village is under 24 hours, and emergency calls get picked up faster when the schedule allows.
- Fox Meadow
- Heathcote
- Greenacres
- Quaker Ridge
- Edgewood
Service Area - Cities Near Scarsdale
We dispatch crews from our New York City office into Scarsdale daily, and we cover the surrounding Westchester communities without handing you off to a subcontractor. If you’re near the village line, we also serve Hartsdale, NY, Eastchester, NY, Tuckahoe, NY, Wykagyl, NY, and Hastings-on-Hudson, NY. Same crew, same standards, same live person answering (877) 610-2993 no matter which side of the Bronx River Parkway you’re on.
Serving Scarsdale, NY - Our Local Coverage Area
Gatewood Fence & Gate crews serve Scarsdale and the communities around it; dispatch is coordinated from our New York City office. The map shows the Scarsdale coverage area; if your address is on it, we can help.
Also serving nearby: Scarsdale, NY, Hartsdale, NY, Eastchester, NY, Tuckahoe, NY, Wykagyl, NY, Hastings-on-Hudson, NY.
FAQs About Gate Repair in Scarsdale
We reach most of Scarsdale within 60 to 90 minutes for urgent calls, depending on where you are and how many jobs are already on the board. A dead motor on a gate that won’t close is a security issue, and we treat it that way. Call (877) 610-2993 and a live person will tell you exactly when the truck arrives.
Only if the repair changes the gate’s appearance. Replacing a rusted iron section with matching fabrication, painting the gate a different color, or altering its profile can require ARB approval. A hinge repair, operator swap, or realignment that keeps the existing look typically does not. We check compatibility before starting and submit the ARB paperwork if your project needs it.
Yes, we cover 10583 entirely, including Fox Meadow, Greenacres, Heathcote, Quaker Ridge, and the Murray Hill area. The same crew handles all of Scarsdale, so you’re not waiting on a different branch or a third-party affiliate. Call (877) 610-2993 for a free estimate - we’ll give you an exact quote before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Scarsdale Customers Say
"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly