Gate Repair in Rendon - Same-Day Repair, Priced Before We Start

Gate Repair in Rendon, TX

Gate repair in Rendon typically costs $150-$600 depending on whether we’re resetting a heaved post, welding a cracked hinge, or replacing a stripped operator gear. Most calls from the 76140 ZIP get same-day or next-day response, because a gate that won’t close is a gate that won’t hold livestock or keep anyone out. Call (877) 610-2993 and you’ll reach a live person, any hour, any day.

Call (877) 610-2993

Rendon sits in an unincorporated pocket of southern Tarrant County where older acreage homesteads with heavy pipe-welded ranch gates now sit directly alongside newer subdivisions with automated driveway gates. That dual reality means our crews show up to the same street with tools for both a 1980s swing gate on hand-set posts and a two-year-old aluminum gate with a failed operator. Hal Gatewood has been at this since 2001, and the person who answers your call can tell you which situation you’re looking at.

Why Rendon Homes Are Different

The ground under Rendon is Vertisol clay, the same black gumbo that cracks foundations across southern Tarrant County. It swells hard after spring rain and shrinks even harder in August drought. A gate post set shallow or without a wide footing moves with it, and the gate that latched fine in April won’t meet the strike in July. We see the same callback pattern every year, peaking in May and October.

The housing stock makes it more complicated. Older acreage properties off Rendon Road commonly have heavy tubular-steel or pipe-welded gate panels hung on posts that were set by hand decades ago, with no engineered footing. Newer subdivisions have aluminum gates on production-builder openers, which often means the cheapest arm and board the builder could spec. Both fail here, just for different reasons. Severe spring weather adds a third factor: wind loads on exposed rural parcels bend cantilever slide tracks and snap operator arms.

Gate Repair in Rendon

Electric gate repair in Rendon usually starts with diagnosing whether the problem is the operator or the gate it’s trying to move. We carry parts for Viking, Ghost Controls, DoorKing, and Elite operators, and we can typically diagnose a board or gear failure in one trip. Most repair calls in the 76140 ZIP trace back to one of three things: a stripped gear from a gate fighting misaligned posts, a failed control board, or a dead power supply on a rural property far from mains power.

Our repair philosophy is simple: fix the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping. That means on-site welding, post resets with proper footings, and honest assessments of whether builder-grade hardware is worth rebuilding. Every repair carries the 90-Day Done Right Promise in writing, and the price we quote is the price you pay. Learn more about our full Gate Repair approach.

Hinge & Post Repair

This is the most common call we run in Rendon. Vertisol clay swells with spring rain and shrinks in summer drought, twisting hand-set concrete gate posts, tilting hinge posts out of plumb, and pulling the latch bar so far off the strike that the gate won’t hold. We reset posts below the clay line with deeper concrete pours, rebuild hinge barrels in place, and weld cracks in the panel frame where stress concentrated during the worst heave. A hinge and post reset typically runs $250-$450 depending on access and whether we need to core below the clay line.

Electric Opener Repair

When an electric gate in Rendon won’t open or close, we start by checking whether the operator is actually dead or just fighting a gate that won’t move square. We carry control boards and gear sets for most major brands, and we can usually swap a failed board or rebuild a stripped gearbox in one visit. Electric opener diagnostics and gear or control board replacement runs $180-$600 depending on the board and operator model, and we always check post alignment first so the new parts don’t get chewed up the same way.

Gate Realignment & Weld Repair

A sagging gate in Rendon isn’t usually a sagging panel-it’s a post that moved. Realigning the gate means getting the post plumb first, then re-hanging the panel and adjusting the latch so it seats without lifting or dragging. On older acreage properties, the original footings often sit shallow in clay that shifts four inches seasonally. We set the new footing below the active soil line, then bring the gate back to square. Gate realignment usually lands between $150 and $300, and weld repair for cracked frame sections runs $120-$350 per cluster, done on site.

Why does my gate stop latching every May and October in Rendon?

Rendon’s expansive Vertisol clay swells with spring rains and shrinks during summer drought, twisting shallow-set concrete gate posts enough to pull the latch off the strike. The fix that actually holds is resetting the post below the active clay line with a deeper footing, which usually runs $250-$450 including realignment. If you’re tired of the twice-a-year adjustment, call (877) 610-2993 and we’ll quote it honestly.

My slide gate track is bent after a spring storm-can you straighten it or does the whole rack need replacing?

If the track steel hasn’t kinked and the bend is gradual, we can usually straighten the track cold and reset the alignment, typically $150-$300. If the rack itself is deformed and the pinion gear has been chewing misaligned teeth, replacing both rack and pinion is the honest fix, typically $350-$600 depending on gate length. Show us the bend and we’ll tell you which one you’re looking at.

Gate Installation in Rendon

Gate installation in Rendon runs anywhere from $1,400 for a simple single-swing driveway gate to $9,000-plus for an automated double-slide gate on a long rural entrance. Most Rendon homeowners spend between $2,800 and $5,500 for a properly engineered gate with operator hardware built for Texas clay soil and wind. That’s the honest range, and we’ll quote your exact number before any work starts.

The key difference in Rendon is the ground. Posts set to code minimums in Vertisol clay will heave, tilt, and ruin a gate that was built square. We over-dig and set posts deeper than minimums because we’ve seen what a normal winter does to a shallow footing. Whether you’re on an older acreage lot off Rendon Road or in a newer subdivision near the Everman line, the gate needs to be built for the soil it’s standing in. See our full Gate Installation options.

Driveway Gate Installation

The driveway gate is the front door to your Rendon property, and it gets treated like one. On acreage lots, we typically install heavy tubular-steel or welded pipe gates on deep-set posts with concrete footings that go below the clay’s shrink-swell line. On newer subdivision homes, we match the aluminum ornamental style your HOA expects but upgrade the hinge posts and hardware so the builder-grade stuff doesn’t fail in two years. A single driveway gate in Rendon typically runs $1,800 to $4,200 depending on width, material, and automation.

Sliding Gate Installation

Sliding gates are common on Rendon acreage where a swing gate would clip a fence line or block a long gravel driveway. We install cantilever and V-track slide gates with operators sized for the gate’s actual weight, not the builder’s optimistic spec. High-wind events from spring severe weather bend cheap slide tracks, so we use heavier-gauge track and proper stops on exposed rural parcels. A sliding gate with operator typically runs $3,200 to $7,000 here depending on gate length and power requirements.

Swing Gate Installation

Swing gates are the classic ranch-style entrance, and they demand proper hinge posts. The Vertisol clay under Rendon heaves seasonally, so we set posts in concrete footings below the active soil zone. A sagging hinge post is where swing gates fail, and we fix it right the first time. Double swing gates on wide rural entrances run $2,800 to $6,500 with automation, while a single swing on a residential lot in newer Rendon subdivisions runs $1,400 to $3,500.

How much does gate installation cost in Rendon compared to Fort Worth or Burleson?

You’ll pay about the same for labor and materials as surrounding cities, but Rendon’s soil and wind conditions mean we sometimes recommend deeper post footings or heavier-gauge hardware that adds a few hundred dollars upfront and saves you a re-do later. A typical residential gate installation here runs $1,400 to $6,500 depending on type and automation. Call (877) 610-2993 for an exact quote, free.

What warranty do you offer on gate installations in Rendon?

Every job carries our 90-Day Done Right Promise in writing. If the gate sags, the operator acts up, or anything we installed doesn’t work right within 90 days, we come back and fix it. That’s not a sales line, it’s stamped on the invoice. That’s how Hal has run the shop since 2001.

Gate Motor & Opener in Rendon

Gate motor and opener work in Rendon means fixing what the clay soil, the wind, and time have done to equipment that was never set up for this ground in the first place. We get called to the 76140 ZIP for everything from a 1980s pipe gate that hasn’t opened square in a decade to a builder-grade opener on a two-year-old subdivision home that already stripped its gears. A live person answers when you call (877) 610-2993.

Most motor failures in Rendon trace back to something upstream: a post that moved, a track that bent, a control board that fried in a spring storm. We start by finding what killed the motor, then fix the root cause and the operator together so you don’t get a callback two months later. We carry parts for Linear, Viking, Ghost Controls, and DoorKing machines. Explore our Gate Motor & Opener service details.

Motor Installation

We install slide and swing gate operators sized for the gate you actually have, not the one a catalog assumes you have. On Rendon’s older acreage lots, that often means a heavier motor than a builder would spec on a subdivision home. We handle the power run, the mounting plate, the safety edges, and the limit settings. Full motor installation on a residential slide or swing gate usually falls between $1,150 and $2,800 depending on operator brand, gate weight, and whether we’re running new power.

Motor Repair

Most motor failures in Rendon trace back to something upstream: a post that moved, a track that bent, a control board that fried in a spring storm. We start by finding what killed the motor. Then we fix the root cause and the operator together so you don’t get a callback two months later. A typical motor repair runs $180-$420 when it’s a straightforward fix like a control board swap, limit switch adjustment, or gear replacement on a still-solid gate.

Battery Backup & Slide Motors

Rendon loses power in storms, and a gate without battery backup becomes a wall between you and your driveway. We retrofit battery backup onto existing operators from Linear and others, even on older systems that still work fine. Battery backup retrofit adds $350-$850 on most systems we see. For cantilever slide gates on rural parcels, we replace stripped racks, rebuild roller carriages, and set limit switches so the gate doesn’t overtravel and bind after a wind event bends the track.

Why do gate motors in Rendon strip gears more often than in Fort Worth or Burleson?

The short answer is the soil. Rendon’s Vertisol clay swells and shrinks more dramatically than ground to the north or south, and that seasonal movement shifts gate posts enough that the motor works against a gate that no longer aligns with its frame. Once the gate binds, the gears are on borrowed time. That’s why we check post square and gate travel before we ever bolt on a new operator.

Can you retrofit a 1980s ranch gate with a modern battery backup operator?

In most cases, the gate stays. If the steel is sound and the post footings are deep enough to hold, we can build a new mounting plate, square the frame, and install a modern operator with battery backup and current safety equipment. We’ve done exactly that on older acreage properties around Rendon where the gate itself is better steel than anything sold today. The gate only needs replacing when the frame is too far gone to square.

Gate Access Control in Rendon

Gate access control in Rendon runs roughly $450 to $2,400 depending on whether you’re adding a keypad to an existing opener or building out a full phone-entry and video intercom system on a long gravel driveway. Most calls we get are for operators that stopped responding to remotes after a spring storm, or homeowners on acreage who want to stop walking out to the gate every time a delivery shows up. We answer the phone 24/7 at (877) 610-2993.

The access control hardware is only as good as the post it’s mounted on, and in Rendon that post is often moving. We check post plumb before we install any keypad or reader, because a keypad on a tilted post will pull its own wiring loose within a season. See everything we offer on Gate Access Control.

Keypad & Remote Entry

A keypad mounted at the driveway is the most common access control upgrade we install in Rendon. On newer subdivisions, a basic wired keypad tied to your existing opener typically runs $180-$450 installed. On older acreage properties with long driveways, you may need a wireless keypad or one that talks to the opener through a receiver, which pushes toward $350-$600. Replacing or adding a remote is $45-$95 per remote depending on brand and frequency.

Phone Entry Systems

Phone entry systems let a visitor call your cell from a box at the gate, you press a button on your phone, and the gate opens. On Rendon acreage where the house sits two hundred feet from the gate, this is often better than an intercom because there’s no wiring pull across the yard. A cellular phone-entry unit installed runs $600-$1,400 depending on whether it’s integrated with your existing opener or needs its own control board.

Card Readers & Full Panels

Card readers show up mostly on shared driveways, small ranches with ranch hands, and a few HOAs at newer subdivisions. The hardware itself runs $400-$900, and installation depends on power availability at the gate and whether you need a standalone reader or one tied into an access control panel. A full access control panel that ties keypads, remotes, and phone entry together starts around $1,200 and goes to $2,400 for multi-device systems.

Is gate access control more expensive in Rendon than Fort Worth?

Generally no, and sometimes it’s less because the drive is shorter from our scheduling office in the Dallas-Fort Worth area. National franchises often charge a trip fee to come south of the city. We don’t charge a trip fee inside the county, and our pricing is the same for Rendon, Everman, Kennedale, and the rest of the immediate area. Your address doesn’t change the hourly rate.

Does your 90-Day Done Right Promise apply to access control work in Rendon?

It applies to every job we do, including keypad, remote, phone entry, and card reader work in Rendon. If something isn’t right, you call us and we come back. We don’t argue about whether it’s covered, we don’t prorate it, and we don’t bury it in small print. It’s stamped on your invoice. That’s how Hal has run the shop since 2001.

Gate Parts & Welding in Rendon

If you have a gate that won’t close, a hinge post leaning out of plumb, or a weld that finally let go after twenty years, we can get it fixed. Gatewood Fence & Gate runs service calls through Rendon every week, from the older acreage places off Rendon Road down to the newer subdivisions that have gone up along the southern edge of Tarrant County. We weld on site, keep a full set of common gate parts stocked, and we don’t tell you to buy a whole new panel when a weld and a new hinge will do. Learn more about Gate Parts & Welding.

Hinge Replacement & Post Reset

Most sagging gates are not sagging in the panel. The hinge pin wears, the barrel elongates, and the whole leaf drops. On Rendon’s older ranch gates, where hinges were often welded directly to a pipe post set in expansive clay, you also get post movement working against the hinge. We replace hinges with greasable units sized to the actual gate weight, then re-hang the panel square. A hinge replacement on a standard double ranch gate runs roughly $180-$340 depending on hinge size and how far the panel dropped.

Post Replacement

This is the big one for Rendon. A gate post set 12 or 18 inches deep in Vertisol clay will move. It heaves when the soil swells, tilts when it shrinks, and after a few seasons the latch misses the strike and the gate panel drags. We cut out the old post, dig a proper 36-inch-deep footing, tie a rebar cage to the new post, and pour it. Post replacement with a proper footing runs $450-$950, and that includes concrete, rebar, and re-hanging the gate.

Custom Welding & Rail Repair

Pipe-welded ranch gates take a beating. A horse leans on one, a trailer clips it, the years flex the frame until a rail cracks at the weld. We can usually cut out the bad section and weld in new tube or pipe on site, rather than telling you to buy a whole new panel. Custom welding for a rail repair or small fabrication job usually lands between $120 and $400. If the frame is too far gone, we’ll tell you that honestly and quote the replacement.

Why does my swing gate latch miss the strike every spring and fall in Rendon?

Because the hinge post is moving in the expansive clay. Rendon’s Vertisol soil swells when it’s wet and shrinks when it’s dry, and a post set shallow will tilt several inches over a season, carrying the latch out of line with the strike. The real fix is a deeper footing with rebar tied to the post, not just adjusting the latch twice a year.

Should I weld the sagging rail on my old pipe gate, or replace the whole panel?

If the rail is cracked at one weld and the frame is still square, weld it. If the pipe is rusted through in multiple spots or the panel has been bent and re-bent, you’ll spend more on repeated patch work than a new panel costs. We’ll tell you honestly which side of that line your gate is on, and we’ll quote both options before any work starts.

Brands We Service in Rendon

We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for Viking, Ghost Controls, and DoorKing operators locally, which means most repairs don’t wait on a warehouse shipment. For parts we don’t have on the truck, our Dallas-Fort Worth office coordinates same-day or next-day delivery to Rendon. See our brands for full details.

Pricing for Gate Repair in Rendon, TX

Neighborhoods We Serve in Rendon

We cover all of Rendon and the 76140 ZIP, from older acreage lots along Rendon Road to newer subdivisions near the Everman line and points south toward the Johnson County border. Typical response time for a gate repair call in Rendon is same-day in most cases; bigger installation jobs get scheduled in writing.

• Rendon Road corridor and surrounding acreage
• Subdivisions near Garden Acres and Eden Road
• Properties along FM 1187 toward Kennedale
• Homes near the Walnut Creek drainage area
• Newer tract developments on Rendon’s eastern edge

Service Area - Cities Near Rendon

We work throughout southern Tarrant County and into adjacent areas, with no trip charge inside the county. If you’re near Rendon, TX, we also regularly serve Everman, TX, Kennedale, TX, Forest Hill, TX, Burleson, TX, and Crowley, TX. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews serve each city locally.

FAQs About Gate Repair in Rendon