Gate Repair in Olive Branch - Same-Day Repair, Priced Before We Start

Gate Repair in Olive Branch, MS

Gate repair in Olive Branch typically costs between $180 and $650 depending on whether we’re fixing a hinge post, an operator, or a weld, and most jobs are finished in a single visit. If your gate is sagging, binding, or stuck in one position on a morning when you need to get to work, call (877) 610-2993 and a live person picks up, day or night. We’re Gatewood Fence & Gate, and Hal Gatewood has been fixing gates the right way since 2001.

Call (877) 610-2993

Why Olive Branch Homes Are Different

Olive Branch’s explosive suburban growth since the mid-1990s produced dozens of HOA-governed subdivisions, many with automated ornamental-iron or aluminum gates installed within a narrow window that are now aging out simultaneously. That means we work a market defined by same-era operator failures - early LiftMaster, Elite, and GTO/Linear units - across tightly clustered planned communities, a pattern you don’t see in older neighboring cities with mixed-age housing.

Then there’s the clay. DeSoto County’s heavy clay soil expands and contracts with seasonal moisture swings, which shoves gate posts up and down and throws swing-gate alignment off every spring. We re-plumb posts and readjust limit switches on gates that were perfectly tuned the prior fall. Add in the humid subtropical weather that rusts steel and iron year-round, plus winter ice storms that freeze operators and snap limit switches, and you start to see why a gate that worked fine in October quits in March.

Gate Repair in Olive Branch

Gate repair in Olive Branch usually falls into two buckets: a motor that quit working, or a gate that’s sagging, dragging, or refusing to close all the way. Either way, we can get a real person out to your driveway fast, and Hal will likely be the one standing there. We know every planned subdivision and HOA entrance along Goodman Road, Getwell Road, College Road, and down toward Lewisburg.

Hinge and Post Repair

We do more hinge post work in Olive Branch than anywhere else in the metro. The reason is the soil. DeSoto County’s expansive clay heaves and shrinks with every wet-dry cycle, and posts that were set only 18 to 24 inches deep - how a lot of 1990s and early 2000s builders did it - get shoved out of plumb every spring. A gate sags in the hinge post, not in the middle. That’s where we start. We dig it up, widen the footing, pour a proper bell-bottom base, and reset the gate. A straightforward hinge repair or post realignment in Olive Branch runs $180 to $450.

Automatic Gate Repair

Automatic gate repair in Olive Branch is heavily weighted toward aging operator failures on same-era installations. Thousands of homes here got early LiftMaster, Elite, and GTO or Linear units installed within a five to ten year window, and those units are now reaching end of service life at the same time. We carry parts for major brands including Viking, Ghost Controls, and DoorKing on the truck, so we’re usually not waiting on a ground shipment to finish the job. The more involved work on automatic operators and electric systems runs $250 to $650.

Electric Gate Repair

Electric gate repair covers the full chain from the keypad and photocells to the motor control board and the wiring in between. Ice storms are a real factor here. The Memphis metro gets them often enough that we’ve learned exactly what fails: limit switches snap when a frozen gate tries to run, condensation corrodes control boards, and surge damage takes out transformers. If your electric gate in Olive Branch stopped responding after a hard freeze, we’ll diagnose it the same day and usually repair it on the spot. Weld and rust repair on steel or iron gates typically falls between $150 and $400 depending on how much metal needs replacing.

Every job is priced and agreed upon before any work starts, in writing. No surprise invoice at the door, no “it was worse than we thought” upcharge. There’s also $40 off any repair over $200, plus no trip charge inside DeSoto County and a permanent 10% discount for seniors and veterans. Learn more about our Gate Repair services.

Does my Olive Branch HOA have to approve hinge post repair before you start work?

For a straight repair that doesn’t change the gate’s appearance, most Olive Branch HOAs don’t require new approval, but it depends on the association’s covenants. If you’re in a subdivision where the gate is HOA-managed, we coordinate with the property manager before we start. When the repair involves a visible change, paint, a new panel, or a different operator housing, the HOA generally wants to sign off first. We’re used to working with both.

Why does my swing gate bind every March in Olive Branch?

Your swing gate binds every March because DeSoto County’s expansive clay soil swells with spring moisture and heaves your gate post out of plumb. If the post was set in a shallow 18 to 24 inch footing, which is common in Olive Branch’s 1990s and 2000s housing stock, the movement is often enough to throw off alignment by a half inch or more. That makes the gate bind against its latch or drag on the driveway. Call (877) 610-2993 and we’ll check the post and reset it properly.

Gate Installation in Olive Branch

A new driveway or entry gate in Olive Branch typically runs $2,800 to $9,500 installed, depending on whether it’s a single pedestrian gate, a double swing gate, or a slide gate with an operator. Most installations take one to two days once materials are on site, and we quote the full price in writing before any work starts. If you’re anywhere in the 38654 area or off Goodman Road, Craft Road, or College Road, we come out and measure for free.

Driveway Gate Installation

A driveway gate in a newer Olive Branch subdivision off Bethel Road or Alexander Road usually means matching the neighborhood’s existing look: heavy ornamental iron with a slide or swing operator. We measure the driveway, check the grade, and tell you honestly whether the ground will take a slide track without constant maintenance or whether a swing gate is the better fit. A single ornamental-iron swing gate for a standard Olive Branch driveway runs $2,800 to $5,200 installed, while a double swing gate runs $4,500 to $8,500.

Slide Gate Installation

Slide gates suit the wider lots and longer driveways you find in Olive Branch’s semi-custom and estate sections, especially where the driveway slopes toward the road. The two things that kill slide gates here are rack and pinion corrosion from humid air and clay movement shifting the track and wheels. We set slide tracks on deeper, more stable footings than the builder standard. A slide gate with operator and track typically lands between $5,500 and $9,500, depending on length and whether we’re reusing existing columns.

Swing Gate Installation

Swing gates are the most common style across Olive Branch HOA subdivisions. The trouble is almost never the gate panel itself, and usually not the operator either. It’s the post. Set properly in a deep concrete footing, a swing gate will outlast the opener. Set shallow in clay, it heaves every spring and you re-align forever. We set hinge posts in footings that go below the soil’s active movement zone, which is the difference between a gate that stays plumb and one you call us about every March. Post replacement with a deep footing runs $450 to $900 per post when needed.

The price we quote is the price you pay. We stand behind it with the 90-Day Done Right Promise, and we don’t start work until you’ve approved the written estimate. See more about Gate Installation.

Why does my Olive Branch swing gate keep going out of alignment every spring?

The clay soil under your hinge posts expands when it absorbs winter and spring moisture, which pushes the posts slightly out of vertical and throws the gate off its latch and limit travel. It’s the most common call we get in Olive Branch between March and May. Re-hanging the gate buys a season. Replacing the post with a deeper footing in stable soil fixes it for good. Call (877) 610-2993 for a free assessment.

My builder-installed double driveway gate sags at the center even after hinge adjustments. What’s actually wrong?

The hinge posts are leaning, or one post has shifted in its footing. Hinge adjustment can’t fix a post that’s moving underground. In Olive Branch this usually traces back to a shallow builder footing from the late 1990s or early 2000s. We pull the post, drill and pour a deeper footing below the clay’s movement zone, re-hang the gate, and align the operators. Call (877) 610-2993 for an exact assessment.

Gate Motor & Opener in Olive Branch

When a gate motor fails in Olive Branch, you don’t have the luxury of waiting a week for a tech to pencil you in. A dead operator means a gate stuck open all night or a driveway you can’t get through on the way to work on Goodman Road. We answer the phone live, 24/7, and we know the subdivisions in Olive Branch better than most people know their own street names.

Motor Installation

A new operator in Olive Branch should be sized for a real gate, not a showroom floor. Many of the original installations in the 1995-2015 subdivisions used builder-grade slide motors that were undersized for the heavy ornamental iron gates they pull. We install operators from trusted brands like Viking, Elite, and Ghost Controls, with the right horsepower for the gate’s weight. A full slide motor replacement on an HOA entrance gate runs $1,800 to $4,200 depending on gate width and weight.

Motor Repair

Most “dead” gate operators in Olive Branch aren’t actually dead. They’ve got a failed relay, a burned limit switch, a corroded capacitor, or a board that can be rebuilt. We open the cabinet and diagnose before we recommend anything. When a board is obsolete, we’ll tell you straight whether a retrofit is practical or whether a new operator is the cheaper answer over three years. A control board replacement on an older LiftMaster or Elite slide operator typically runs $350 to $650 installed.

Linear Motor Service

Linear arms are everywhere in Olive Branch because the planned communities favored ornamental aluminum driveway gates with limited clearance. The arm itself is simple, but the failure usually isn’t the arm. It’s the post. DeSoto County clay moves every season, and a linear motor that’s working against a shifted post will burn out its gearbox in a year. We check the post plumb before we touch the arm. A solar-ready linear motor for a residential driveway gate runs $900 to $1,800 including installation.

Every quote is written and agreed to before work starts. Free estimates for Olive Branch homeowners and HOAs, and $40 off any repair over $200. More on Gate Motor & Opener service.

My HOA gate uses an early LiftMaster slide operator from around 2000. The board is dead-do I have to replace the whole motor?

Usually not. The chassis, gearbox, and rail on those early LiftMaster units are still solid, and the failure is almost always the control board. We retrofit a current board into the existing cabinet and re-tune the loop detector. That runs a few hundred dollars instead of the $2,500 to $4,000 a full replacement costs in Olive Branch. Call (877) 610-2993 and we’ll look at what you’ve got.

After the last ice storm, our subdivision gate is stuck half-open and the opener just hums. What likely failed?

You’ve probably got a snapped limit switch or a sheared gear, both common after an Olive Branch ice event. The motor has power - that’s the humming - but the gate can’t complete its cycle. We check the switches, the gear assembly, and the photocell alignment, and we fix what’s actually broken rather than selling a new operator. Call (877) 610-2993 for same-day diagnosis.

Gate Access Control in Olive Branch

Gate access control work in Olive Branch usually means one of three things: a keypad that’s stopped reading codes, a phone-entry system that won’t ring the house, or a full upgrade because the HOA just changed the entrance requirements. Hal Gatewood answers his own phone at (877) 610-2993, and he’ll tell you straight whether your system is worth fixing or if it’s time to replace it.

Keypad Entry

Keypad entry systems in Olive Branch fail in predictable ways: the membrane cracks from summer heat and winter ice cycles, or the wiring inside the post corrodes and stops carrying signal. We diagnose first, then replace only what’s actually dead. If the keypad failed because the post is leaning - common in the clay-heavy soil around Center Hill - we address that first, because bolting a new keypad to a shifting post just means you’ll call us again in spring. A new residential keypad with installation runs $350 to $750.

Phone Entry

Phone entry systems - the kind where a visitor calls your cell from a box at the gate - are especially common at Olive Branch’s gated subdivision entrances and run on cellular networks and POTS lines that are gradually being retired. We handle the wiring, the SIM activation, or the switch to a VoIP-based system. Many HOAs in Olive Branch are facing this transition right now because the old telephone-line infrastructure is finally going dark. Phone entry starts at $900 for a single home and climbs for multi-resident or HOA-scale systems.

Remote Control and Card Reader

If your gate stopped opening with the remote but works fine from the wall button, the remote itself is the likely culprit, but we check the receiver board before selling you anything. Olive Branch is full of LiftMaster, Elite, and older GTO/Linear openers that are now twenty-plus years old, and their receiver ranges degrade over time. New remote transmitters with programming typically run $85 to $220, and a receiver replacement runs $200 to $600 depending on how many transmitters you need. A single card reader replacement installed runs $450 to $950.

Every gate access control job in Olive Branch includes a free on-site assessment, and the price is quoted and agreed in writing before we touch a single wire. Details on Gate Access Control.

Can you handle emergency gate access control calls in Olive Branch?

Yes. A gate stuck closed at midnight or locked open at a subdivision entrance is a security and safety issue, and we answer calls 24 hours a day, 7 days a week. If your gate access control failed during an ice storm or a summer storm and you need it fixed now, call (877) 610-2993. Hal will answer, and if it’s an emergency, he’ll tell you exactly when he can get there.

Does your 90-Day Done Right Promise apply to access control work in Olive Branch?

Yes. Every access control job we do in Olive Branch carries our 90-Day Done Right Promise in writing. If something we installed or rebuilt isn’t right within those 90 days, one call brings us back without an argument. That guarantee is part of why most of our Olive Branch jobs come from referrals - neighbors telling neighbors who actually fixed their gate right the first time.

Gate Parts & Welding in Olive Branch

Gate parts and welding in Olive Branch usually breaks down to two jobs: replacing worn hardware before it ruins the gate, or fixing a structural failure that starts in the post, not the panel. We do both, and we do the welding on site in your driveway so the gate never leaves your property. Hal handles the welding personally when the job calls for it.

Hinge Replacement

Gate hinges in Olive Branch take a beating from humid summers and wet springs. The factory hardware on many 1995-2015 planned-community gates was lightweight from the start, and once rust gets into the pin and barrel, the gate starts sagging and binding at the latch. That’s the hinge failing, not the gate. We’ll swap the old hinges for heavier-duty hardware rated for the weight of your panel. A typical hinge replacement runs $120 to $260 for one or two pairs on a standard residential gate.

Post Replacement

Here’s the thing about gate posts in Olive Branch: the clay soil moves. A lot. Post replacement is not just about pulling a bent post out of the ground and dropping in a new one. It’s about setting the next post deeper, with proper concrete and better drainage, so it doesn’t heave again next spring. We’ve replaced posts from College Road to the far side of 38654 that looked perfect until you put a level on them. Post replacement runs $300 to $580, including digging out the old footing, setting the new post in concrete, and rehanging the gate.

Rail Repair and Custom Welding

Ornamental iron and aluminum gates get their strength from the rails, and when a rail cracks or a weld pops loose from the upright pickets, the whole panel loses its rigidity. We see this all the time on older decorative gates around Olive Branch subdivisions, especially near the bottom rail where moisture and lawn equipment work against the metal. We weld cracks on site and fishplate rails that are too far gone for a simple patch. Rail repair and custom welding runs $150 to $350 for most single-rail cracks and bracket or gusset fabrication.

The price we quote is the price you pay, no new number at the door. We also run a standing offer of $40 off any repair over $200. More on Gate Parts & Welding.

Can you weld a gate post that’s cracked but still standing?

Sometimes yes, but it depends on where the crack is and how much the post has moved. A cracked post that’s still plumb can often be welded and reinforced on site. A post that’s leaning or rotted at the base needs replacement, not a patch. We’ll tell you the truth about which one you have and quote the repair before any work starts. Call (877) 610-2993 for a look.

Are gate part and welding costs in Olive Branch higher than Memphis or Southaven?

No, you’ll find our pricing is the same across the metro. Hinge replacement in Olive Branch runs $120 to $260, and post replacement falls between $300 and $580. The soil here is clay-heavy, which sometimes means a slightly deeper footing for a replacement post, but we build that into the quote upfront rather than surprising you with it later.

Brands We Service in Olive Branch

We stock parts and carry service certification for nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our Memphis office keeps common boards, gear assemblies, safety photocells, and loop detectors on hand specifically because Olive Branch’s same-era installations fail in predictable patterns. That means faster turnaround and fewer callbacks.

Pricing for Gate Repair in Olive Branch, MS

Neighborhoods We Serve in Olive Branch

We run jobs all over Olive Branch, from the big HOA communities to the ranches and semi-custom homes further out toward the county line. Typical response time is same day for urgent repairs and next morning for scheduled work. We cover the entire 38654 ZIP code with no trip charge inside DeSoto County.

• Windsor Hills and surrounding subdivisions
• Lewisburg / Craft Road corridor
• College Road area
• Goodman Road communities
• Center Hill and east Olive Branch

Service Area - Cities Near Olive Branch

We coordinate dispatch and scheduling from our Memphis office, and crews serve Olive Branch, MS locally every day. We also run regular routes to Southaven, MS, Horn Lake, MS, and Hernando, MS with the same upfront pricing and the same live-answer phone line.

FAQs About Gate Repair in Olive Branch