Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Norco
Gate access control in Norco usually means retrofitting an older ranch gate, not swapping out a suburban driveway opener. Homes here sit on acre-plus lots with 14 to 16 foot pipe-frame swing gates built for horse trailers and equipment, and the access systems on them span fifty years of technology. We work on keypad entry, remote controls, phone entry, card readers, video intercoms, and loop detectors on gates that were welded before modern safety standards existed. If you live near Corydon Avenue, Hammer Avenue, or up against the Santa Ana River, we can be at your gate quickly. Call (877) 610-2993 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Norco’s Preferred Gate Access Control Company
Hal Gatewood started this shop in 2001 and he still answers the phone himself most days. Norco homeowners tend to check up on who they’re hiring, and that works in our favor, because our license number is published and Hal’s name is on the shop. We’re not a franchise with a rotating roster. The person who shows up to your gate in Norco is the person you’ll see at the feed store next week.
We’ve spent years untangling the particular mess that older Norco properties hand us: control boards baked by 105 degree summers, swing gates with hinge posts rotted out at the footing, and remote receivers that work fine from the kitchen window but fail at the curb. A lot of companies would quote you a whole new opener for half of those jobs. We fix what’s fixable and we tell you plainly when fixing something twice will cost more than replacing it once.
Every job we do in Norco carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. We also honor standing offers that don’t involve haggling: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. You’ll know the price before we touch a wrench.
Our Gate Access Control Services in Norco
Keypad Entry
Adding a keypad to an older Norco gate is usually straightforward, even when the gate itself is a heavy pipe swing gate from the 1970s. A typical keypad entry retrofit in Norco runs $280 to $480, depending on whether we’re wiring a standalone keypad at the post or integrating it with the existing opener. We set codes and walk you through the programming before we leave, and we mount the keypad where you can reach it from the driver’s seat without leaning across a horse trailer.
Remote Control
Remote controls fail silently. Batteries die, receivers drift off frequency, and old remotes from obsolete systems simply aren’t made anymore. We program universal remotes and new receivers for Norco gates so your existing opener keeps working without replacing the whole motor. A remote replacement or reprogramming call in Norco typically runs $95 to $180. If we can’t match the frequency, we’ll tell you before you pay for a service call.
Phone Entry
Phone entry systems let you buzz a gate open from your cell phone, which matters on Norco properties where the gate is 200 feet from the house. We install and repair cellular-based gate entry so you don’t need a landline at the property. A phone entry unit for a Norco residential gate runs $500 to $900 installed. The good ones let you add temporary access codes for the farrier, the hay delivery, or a horse trainer without giving them your house code.
Card Reader
On equestrian properties where multiple people come and go, a card reader at the gate beats handing out remotes that go missing in the barn. We install proximity card readers at the post and tie them into your existing opener, so ranch hands, boarders, and family members each have their own access card. A card reader addition in Norco typically runs $350 to $600 per entry point. If someone stops being welcome, you delete their card. You can’t do that with a lost remote.
Video Intercom & Loop Detector Integration
Norco gates sit far from the house, and a video intercom closes that distance with real picture, not just a buzzer. We retrofit video intercoms onto older ranch gates using low-voltage wiring or cellular links where no wire exists. A video intercom retrofit in Norco runs $650 to $1,500 depending on how far the signal has to travel and whether we’re mounting on block wall or pipe post. Loop detectors go in the driveway so a vehicle or trailer swings the gate open automatically, but they need careful tuning on Norco lots so horses standing near the gate don’t trigger false opens.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Norco
We service and stock parts for DoorKing, Viking, and Ghost Controls operators, plus most legacy brands still running on Norco gates. That matters because we can often repair a control board or a limit switch the same week instead of waiting on a discontinued part. Hal is certified on nine major gate brands, and when a board is truly obsolete, we’ll retrofit the opener with current electronics rather than making you buy an entire new operator. On a ranch gate with a working motor and a dead control board, that’s the difference between a $400 board replacement and a $2,000 opener swap. We show you the failed part and explain exactly what we’re doing, so you never pay for work you can’t see.
Common Gate Access Control Problems We See in Norco Homes
- Obsolete 1970s control boards with burned relays. Norco summers exceed 105°F, and control boards mounted inside black metal housings fry their relays. The gate dies in whatever position it was in when the relay burned, which is why so many Norco swing gates sit stuck open during Santa Ana wind events.
- Worn hinge posts on heavy pipe-frame gates. Horses lean, rub, and occasionally kick gates. Over decades, the hinge post moves in the ground, the gate binds on the strike plate, and the opener strains until it trips or smokes. Sag correction won’t hold unless the post footing is rebuilt first.
- UV-degraded keypad and intercom wiring. Low-voltage wire run along block perimeter walls in full sun develops cracked insulation. Moisture gets in, shorts happen, and you get phantom triggers or a keypad that works in the morning and quits by noon.
- Remote works at the house but not at the street. The receiver antenna on an older opener may be oxidized, tucked inside a metal post, or simply too weak after twenty years. We diagnose range issues with a signal meter, not by selling you a new remote and hoping.
Pricing for Gate Access Control in Norco, CA
Honest numbers for Norco, because you should know before you call. A keypad entry retrofit runs $280 to $480. Remote programming or replacement, $95 to $180. Phone entry systems, $500 to $900. Card readers, $350 to $600 per entry point. Video intercoms, $650 to $1,500 depending on wire distance and mounting. A new control board for an older operator runs $300 to $550 installed. A full swing gate motor replacement on a dual-leaf pipe gate runs $1,200 to $2,400 depending on gate weight and opener brand. We quote the price before any work starts and it does not change at the door. Estimates are free. Call (877) 610-2993 and we’ll give you a number you can hold us to.
We Also Serve Cities Near Norco
Our Gate Access Control team works throughout the Norco area, and we regularly serve Gate Access Control in Norco neighbors in Eastvale, Home Gardens, Corona, and Jurupa Valley. If you live near the county line or close to a neighboring city, call us and we’ll tell you honestly whether we can reach you quickly.
Serving Norco, CA - Our Local Coverage Area
We’re based in the Norco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Norco
Yes, you can add a keypad to most older ranch gates in 92860 without replacing the opener, as long as the opener itself still responds to a wired or wireless trigger input. On a 1970s-era hand-welded pipe gate, we mount a weatherproof keypad at the post, wire it into the opener’s activation terminal, and program your codes on site. A keypad retrofit on this type of Norco gate typically runs $280 to $480. If the opener’s control board is dead, we’ll show you the board and quote the repair before recommending a retrofit. Call (877) 610-2993 for a free estimate.
Heat expands steel frames and the gate binds against the strike plate or the post, tripping the opener’s obstruction sensor. The root cause is usually a hinge post that has shifted in the ground over decades, and Norco’s summer temperatures make the binding more obvious. Tightening or replacing the hinge alone won’t fix it if the post footing is moving; the post needs to be re-set and re-welded first. Call us for a free look at your gate.
Yes, a safety photocell is essential on any automated gate, especially on an equestrian property where horses, dogs, kids, and trailers move through the same opening. Norco gates from the 1970s and 1980s often predate the UL 325 requirement for safety entrapment protection, so they may have been installed with no photocell or reverse sensor at all. We retrofit photocells onto older operators so the gate reverses if a horse or person crosses the beam while it’s closing. On Norco lots, we also wire them so horses standing near the loop don’t hold the gate open. Call (877) 610-2993 to have your gate checked.
Yes, we can retrofit a video intercom onto a 1980s Norco ranch gate even when there’s no low-voltage wire run to it. We use cellular-connected intercom units that talk to your phone over LTE, which avoids trenching across an acre of horse pasture at high cost. A cellular video intercom retrofit in Norco runs $650 to $1,500 depending on the unit and mounting. If you do have existing multi-conductor wire, we’ll use it and save you the subscription. Call us and we’ll walk the property and give you a real quote.
The receiver board or antenna in the opener has failed, while the keypad works because it’s wired directly to the activation terminal. On older Norco gates, this is usually a burned-out receiver module inside the control board, often cooked by years of Inland Empire heat inside a metal housing. We replace or bypass the receiver with a current unit and reprogram your remotes, typically for $150 to $250. If the keypad and the remote both quit, that points to the main control board instead. Call (877) 610-2993 for a free estimate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Norco since our founding in 2001.