Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Newport
Gate access control in Newport means keypads, remotes, card readers, and video intercoms that keep working through river-valley humidity, ice storms, and the occasional flood. Most repair calls we take from Newport get a same-day or next-morning visit, and every job carries our 90-Day Done Right Promise in writing. If your gate opener quit after the last storm or your keypad is flashing an error you don’t recognize, call us at (877) 610-2993 and talk to a real person. Hal Gatewood has been running this company since 2001, and his name goes on every invoice.
Why Gatewood Fence & Gate Is Newport’s Preferred Gate Access Control Company
We’ve been working on Gate Access Control systems around Newport long enough to know which corners of 37821 and 37822 take the worst of the river fog and which hillside lots shade out solar panels by 3 p.m. in winter. Newport customers tend to find us after a national outfit quoted one price and charged another at the door. That doesn’t happen here. Hal quotes the work before it starts, and the price doesn’t move unless you add scope to the job.
Our crews know the ground here. We’ve pulled silt out of slide-gate tracks off River Road, re-set hinge posts that shifted in saturated clay after a Pigeon River rise, and replaced keypad housings cracked by freeze-thaw cycles that hit this valley harder than the higher towns around us. When you call, you get a live person, any hour. Not a voicemail. Not a chatbot. Hal or someone who works directly with him.
Our Gate Access Control Services in Newport
We install, repair, and service the full range of access control hardware on gates across Newport. Here’s what that looks like in practice around here.
Keypad Entry
Most keypad failures we see in Newport come down to moisture or corrosion. The housing cracks after a hard winter, water gets inside, and the membrane buttons stop making contact. We replace units with weather-sealed housings and stainless fasteners as standard practice, because anything less just rots in this valley. Typical keypad replacement in Newport runs $180-$320 including parts and programming. If the post is rusted at the base, we weld in a new mounting plate on site rather than telling you to dig a new footing.
Remote Control
Adding a new remote or reprogramming one that stopped working is quick work. Most Newport driveways use LiftMaster or Linear receivers, and we stock matching remotes in the truck so we’re not ordering parts and coming back next week. A single remote programmed to your existing operator runs $85-$140 in Newport. If the receiver board itself has failed, that’s more like $240-$400. We’ll show you the failed part before we replace it.
Phone Entry
Phone-entry systems let you buzz the gate open from your cell or store a guest number in the system. Around Newport, we often pair a phone entry controller with a video intercom so you can see who’s at the gate before you open it. For rural properties off the main roads, where you might be at the barn or down by the river, being able to open the gate from anywhere beats walking to the driveway every time. A complete phone-entry add-on to an existing opener typically runs $450-$800 in Newport.
Card Reader
Card readers make sense for larger Cocke County properties with hired help, farmworkers, or multiple vehicles coming and going. We install proximity readers that work with the operators we already service, and we can enroll cards while we’re there. Expect to pay $400-$750 for a card reader integrated with your existing opener, depending on whether we’re adding a standalone controller or tying into a system you already have. If your existing reader got submerged in a flood, we’ll check the wiring rather than just swapping the head.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Newport
We’re certified to service nine major gate brands, and for Newport specifically we most often work on FAAC, Linear, and Viking operators, plus LiftMaster on the residential side. BFT shows up on a lot of the older farm gates out in the county. Because we see these same brands week after week in Cocke County, the truck carries common replacement boards, remotes, and weather seals. That means fewer return trips and a lot less waiting on parts that have to ship from somewhere dry. If you’ve got an older unit another company said was obsolete, ask us first. Hal fixes what others want to replace.
Common Gate Access Control Problems We See in Newport Homes
- Flood silt in slide-gate tracks. Low-lying lots near the Pigeon or French Broad take on river silt after high water. It packs into the track channel and jams the rack-and-pinion, which makes the operator fault out or strain the motor. We keep track-cleaning tools and penetrating lubricant on every truck for exactly this.
- Hinge posts loosened by saturated ground. After heavy rain or flooding, the ground around a hinge post softens and the post moves. That throws off the safety photocells so the beam doesn’t align, and the gate starts dragging in the middle. We re-set and brace the post in place rather than telling you the whole gate is scrap.
- Freeze-thaw cracking on keypad and card reader housings. Newport’s winter ice storms and repeated freezing cycles crack plastic housings and corrode contacts. The fix is a weather-sealed unit with stainless hardware. We learned that one the hard way years ago and haven’t looked back.
- Operators seizing after ice storms. When an ice storm coats the gate and the operator arm, the motor can bind and trip its internal overload. Half the time the fix is mechanical, not electrical. We thaw it, lubricate the drive, and verify the entrapment sensor still works before we leave.
Pricing for Gate Access Control in Newport, TN
Here are straight numbers from the work we do in Newport. A keypad replacement runs $180-$320. A single remote programmed on site runs $85-$140. A receiver board replacement falls between $240-$400. Phone entry systems start around $450 and run to $800. Card readers land between $400-$750. A full video intercom with a phone app, which we’re installing more often on rural Newport driveways, typically runs $900-$1,400. Every price gets quoted and agreed before any work starts. No trip charge inside the county. $40 off any repair over $200. Seniors and veterans get a permanent 10% discount. Call (877) 610-2993 for a free estimate on your specific gate.
The one thing that pushes a Newport price higher than expected is corrosion damage you can’t see until the housing comes off. We’ll open it up, show you what’s there, and quote the work before we touch anything. If you’ve got a written estimate from another company, bring it to us. Hal will give you a free second opinion.
We Also Serve Cities Near Newport
If you’re outside Newport, Gate Access Control in Newport extends to our neighbors in Morristown, Jefferson City, Sevierville, and Pigeon Forge. Same crew, same 90-Day Done Right Promise, same phone number: (877) 610-2993.
Serving Newport, TN - Our Local Coverage Area
We’re based in the Newport area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Newport
Every automatic gate has a manual release. On most residential operators it’s a small keyed or pull lever on the motor housing. Pull it and the gate swings or slides freely by hand. On LiftMaster and Viking units there’s a keyed release cylinder, and on many Linear models the release is a loop or handle you pull down. If you don’t know where yours is, call us and we’ll walk you through it by phone. After the power comes back, re-engage the release and let the operator cycle once or twice to make sure the limits are still set. Ice storms knock out power in the Newport valley at least a couple times a winter, so it’s worth knowing where that release is before the lights go out.
Once a year is sensible for most Newport gates, and twice a year if you’re on a low-lying lot near the river. The humidity here accelerates corrosion on boards, terminals, and fasteners, and the first thing that fails is usually a limit switch or a safety photocell connection. A yearly service call runs about $120-$180 in Newport and covers cleaning, lubrication, limit adjustment, and a check of every connection. It’s cheaper than a new control board at $300-$500.
No. Not reliably. Hollow lots in the hills outside Newport lose direct sun early, especially in winter, and a solar panel that sits in shade for half the day will undercharge the battery until the operator faults out. If you’ve got a full-sun southern exposure, solar works fine and saves you a power run. If not, we’ll run a low-voltage line instead. When someone asks us to install solar on a shaded lot, we tell them the truth and quote the wired alternative. Hal would rather lose a sale than put in something he knows will fail.
The flashing light means the photocell beam is interrupted or the two eyes are out of alignment. In Newport, the usual cause is a shift in the gate or post from saturated ground after rain. The beam gets pointed at the wrong spot and the system thinks something is in the way. The fix is realigning the photocells and tightening the post or bracket that moved. Spray a little water on the lenses and wipe them too. If the light keeps flashing after alignment, the photocell itself has likely failed. Expect a replacement photocell set to run about $80-$150 in Newport, installed.
You don’t prevent it with the hinge alone. A swing gate on a slope wants to push its weight downhill, and the hinge post takes all of it. We set posts deeper than standard on sloped Cocke County lots and brace the hinge post with a welded gusset or a second anchor point when the grade demands it. For existing gates that have started to sag, we’ll usually weld a cross-brace or replace the hinge barrels on site rather than pulling the gate and rebuilding it in a shop. Installing a gate right the first time on a slope costs more than flat-ground work, but it’s the difference between a gate that lasts and one that drags after two winters. Call (877) 610-2993 for an on-site look at your grade.
Call Gatewood Fence & Gate for Gate Access Control in Newport
If your keypad is dead, your remote quit, or your gate hasn’t cycled right since the last storm, call us. We’ll show up, look at the gate, and quote the work before anything gets taken apart. The name on the shop is Hal Gatewood’s. The shop has been running since 2001. And the person who answers the phone at (877) 610-2993 is a real person, any hour, any day. Ask for the free estimate, and ask about the 90-Day Done Right Promise. It’s in writing on every job.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Newport since 2001.