Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Naples, FL
Gate repair in Naples typically runs between $180 and $750 depending on whether it’s a hinge, a motor board, or a welded frame repair, and most residential calls here can be handled the same day. We’re Hal Gatewood’s crew, and we’ve been fixing automated gates since 2001. Call us at (877) 610-2993 and a live person picks up, day or night, every time.
Why Naples Homes Are Different
Naples has one of the highest concentrations of gated communities per capita in the United States. Port Royal and Aqualane Shores have private estate driveways with custom swing gates. Pelican Bay, Mediterra, Grey Oaks, and Tiburon run community entry systems that log thousands of open-close cycles a week. Gate repair here isn’t an occasional add-on. It’s the dominant residential service call in the market.
Then there’s the Gulf itself. Sitting directly on the water means salt-laden air moving over your gate hardware every single day. Chrome and zinc-coated hinges that would last a decade in Orlando fail in two to three years here. Control boards corrode. Hydraulic seals degrade. And from June through September, the near-daily lightning storms destroy operator boards with regularity. We stock parts for those summer calls because we know they’re coming.
Gate Repair in Naples
A broken gate in Naples isn’t something you can put off. Whether it’s a driveway swing gate frozen half-open in Old Naples or a community slide gate binding at the entry to Pelican Bay, the problem gets worse and more expensive the longer it sits. We run calls across the city daily, and in a market this dense with automated gates, we see every failure mode Naples has to offer. For a deeper look at how we approach the work, see Gate Repair. Here’s what we’re actually fixing out here.
Hinge and Post Repair
This is the most common gate repair in Naples, and it’s the one most companies get wrong. Salt-laden Gulf air oxidizes swing gate hinge posts and weld joints within two to three years. The gate starts to sag, the latch stops lining up, and the motor strains against a post that’s no longer plumb. A gate sags in the hinge post, not in the middle. Hinge and post repair on a residential swing gate typically runs $250 to $600 depending on how much structural steel needs replacing.
Electric Gate Repair
Salt air and electric components do not get along. A control board that would last a decade inland may fail in two to three years in Naples. When a LiftMaster or Viking board dies from moisture intrusion or a lightning strike, we diagnose it on site and replace what actually failed, not the whole system because it’s easier to bill. Electric gate repair, including a new control board or photo eye, usually lands between $200 and $500 for the part and the visit.
Weld and Rust Repair
Wrought iron and ornamental aluminum gates throughout Old Naples and the Moorings show rust at the weld joints, the bottom rails, and wherever the finish has been scraped by a closing gate. We grind out the rust, weld in new material, and leave the gate structurally sound and ready for paint or powder coat. Weld and rust repair jobs start around $150 and go up from there based on how much steel is involved. This is the repair-first work we’ve built our name on.
How much does gate repair cost in Naples?
Most residential gate repairs in Naples land between $180 and $750 depending on whether it’s a hinge, a motor board, or a welded frame repair. Hinge and post repair runs $250 to $600, electric repair $200 to $500, and weld work starts around $150. Every price is quoted and agreed before work starts. Call (877) 610-2993 for an exact quote, and remember we take $40 off any repair over $200.
Can you fix my gate the same day in Naples?
Yes, in most cases. We stage trucks locally so a typical Naples repair call is handled same day, and a live person answers at (877) 610-2993 to tell you exactly when we’ll be there. Community gate emergencies in Pelican Bay or Grey Oaks get priority because a stuck entry gate backs up an entire neighborhood. Call and we’ll give you a real arrival window.
Gate Installation in Naples
A new driveway gate installation in Naples typically runs $4,200 to $14,000 for a complete automated swing or slide gate, and most jobs take two to four days once materials and permits are in hand. The real issue in Naples is rarely the gate itself. It’s what was omitted during construction: the power run, the conduit, the loop detector, the safety edges. For the full scope of what we build, see Gate Installation. Here’s what that work looks like on the ground.
Driveway Gate Installation
Most driveway gates we install in Naples are automated swing gates on single-family lots in communities like the Moorings and Livingston Woods, or slide gates on the wider driveways common in 34108 and 34110. We set the posts deep enough to carry the gate, run the power, and install the operator, loop detector, and safety edges as one job. A manual single swing gate installation runs $1,800 to $4,500 including posts, hardware, and fabrication.
Sliding Gate Installation
Sliding gates are the workhorse of Naples master-planned communities. High-cycle entry gates at Pelican Bay, Mediterra, and Grey Oaks activate thousands of times a week, and the ones that survive are installed with proper track, proper rollers, and operators sized for the load, not for the lowest bid. Slide gate installations run $6,000 to $18,000 for high-cycle community systems depending on gate length and operator class.
Automated Swing Gate Installation
For a custom estate home in Old Naples or Port Royal, a double swing gate puts enormous load on the hinge posts. We start at the post, because a gate sags in the hinge post, not in the middle. A complete automated swing gate installation with operator, control board, loop detector, safety photocells, and wiring runs $5,500 to $14,000 depending on gate size and material. If your gate is retrofitting a manual install with missing conduit, plan on $800 to $2,500 additional for the electrical and trenching work.
Why do so many newer Naples homes with gates have zero wiring for a gate operator?
Because builders in Naples have been installing manual gates as an architectural feature while leaving the electrical and conduit out to cut cost. Then the home sells, the new owner wants automation, and there’s no power anywhere near the gate. We see this constantly in Pelican Bay, Mediterra, and Grey Oaks. The fix is running conduit and electrical from the house or nearest panel to the gate location, which we handle before the operator ever goes in. Call (877) 610-2993 for a written price.
Can an HOA in communities like Pelican Bay or Mediterra require specific gate operator brands?
Yes, absolutely. Many Naples HOAs have architectural review boards and access control specifications that dictate the type of gate operator, the brand, and even the entry system you can install. We’re certified on nine major brands, including Linear, DoorKing, and Viking, so we can install whatever your HOA requires. We submit the paperwork before we install, not after. Call (877) 610-2993 and we’ll help you get the approval moving.
Gate Motor & Opener in Naples
When a gate motor quits in Naples, it’s usually a driveway blocked or an HOA entry down while a dozen homeowners line up behind it. We know the failure patterns here: salt air killing circuit boards, lightning striking operators from June through September, and seasonal owners coming back in October to find a gate that won’t budge. For the full scope of motor work, see Gate Motor & Opener. Here’s what we actually run into.
Motor Repair
We repair motors in place whenever it makes sense. A seized gear, a burned capacitor, a water-damaged board: these are fixable, and we’ll tell you that plainly. A basic motor repair, like replacing a capacitor or a limit switch, typically runs $185 to $340 including the part and the trip. In this salt air, we also swap hardware that’s quietly rusting before it becomes a call at 10 p.m.
Full Operator Replacement
When a motor is truly done, we replace it with an operator sized for the gate’s actual weight and duty cycle, not whatever’s sitting on a shelf. A full operator replacement on a standard driveway swing gate usually lands between $1,400 and $2,800. Slide gate operators at community entries run higher, often $2,500 to $4,500, because the motor, rack, and controls all work harder. Every quote is written and agreed before work begins.
Lightning Damage Repair
From June through September, Naples gets daily lightning. A single strike a block away can send a surge through a gate’s power line and take out a DoorKing or Ghost Controls board instantly. We see more of this in Naples than almost any other failure type during storm season. We replace burned control boards, wiring, and capacitors, and we stock the common boards so we can usually get a summer storm call back online the same visit.
How fast can you get to Naples for a gate motor emergency?
In most cases, we respond to Naples service calls the same day, and often within a couple of hours for a gate that’s stuck closed or stuck open. A live person answers at (877) 610-2993 and tells you right then when we can be there. Emergency service is available around the clock, and we stock the boards and motors that Naples eats through every summer.
Can you fix a gate motor that was damaged by lightning in Naples?
Yes. We replace burned control boards, wiring, and capacitors after storm season hits. If lightning damaged your opener, we can usually repair it the same day if it’s a board swap, or quote a replacement operator if the damage is more extensive. Call (877) 610-2993 and describe what happened. We’ll tell you honestly what it’ll take and what it’ll cost before anything starts.
Gate Access Control in Naples
Gate access control in Naples means working with HOAs, architectural review boards, and property managers who approve every component before it gets installed. That’s the reality of this market. Here is the thing: the salt air here eats keypads and card readers faster than almost anywhere in Florida, and the summer lightning season knocks out entry boards on a schedule. For the full scope, see Gate Access Control. Here’s what we handle.
Keypad Entry
Many Naples homes in communities like the Moorings and Park Shore still run keypads installed in the 1990s and early 2000s. Gulf air salt gets into the circuit board, the membrane buttons stop responding, and the keypad still looks fine from the outside. A keypad entry replacement in Naples typically runs $350 to $650, including the new keypad and labor. We use weather-sealed units built for coastal exposure.
Card Reader Replacement
Card readers at HOA entries log thousands of activations per week. When card reader contacts corrode, the reader drops cards randomly or stops reading entirely. A replacement card reader at a Naples community entry typically runs $450 to $800 plus panel integration time if the wiring is still good. We clean, rewire, or replace readers and tie them back into the existing access control panel so the property manager keeps the same system.
Phone Entry Systems
Phone entry systems tied to resident call boxes are common at smaller Naples HOA entries and private driveways in 34102 and 34103. We install and repair GSM-based and VoIP phone entry modules that call a resident’s cell when a visitor presses the button. Installed phone entry systems run $700 to $1,200 depending on access distance and existing wiring. These systems need to survive salt air and the summer humidity spike, so we spec enclosures rated for exactly that.
Does my Naples HOA require architectural approval before I replace a gate operator or add a keypad entry system?
In most Naples gated communities, yes. Communities like Grey Oaks, Mediterra, and Tiburon have design standards that govern gate hardware, finish color, pedestal style, and sometimes even the operator brand. We ask for the current standards in writing before starting any shared entry work, and we supply the exact model and finish specs your board needs for a fast approval. Call (877) 610-2993 and we’ll help you get the paperwork moving.
Why does my gate access keypad stop working every summer even though it was fine in winter?
Salt-laden Gulf air corrodes the keypad circuit board and button contacts far faster in Naples than inland Florida. The same keypad that lasted eight years in Orlando may fail in two to three years here. The fix is a weather-sealed keypad rated for coastal exposure, not another consumer-grade unit. We install the right equipment for this climate and wire it so the board is protected from direct salt contact. Call (877) 610-2993 for an exact quote.
Gate Parts & Welding in Naples
Gate parts and welding in Naples comes down to one thing: the salt air eats hardware faster here than anywhere inland. Hinges seize, rollers pit, posts shift in saturated soil, and a gate that worked fine in April might be frozen stiff by November. For the full parts operation, see Gate Parts & Welding. Here’s the work we do most.
Hinge Replacement
Salt-laden Gulf air destroys standard gate hinges in two to three years, especially within a mile of the coast in 34102 and 34103. Hinge replacement on a standard single swing gate typically runs $180 to $340, including stainless hinges and the welds to set them. We replace seized hinges with stainless steel or heavy-gauge galvanized options selected for how close your gate sits to the water.
Post Replacement
Post failure in Naples usually starts underground. Storm season saturates the soil, footings shift, and a gate that weighed evenly on its hinges suddenly hangs on one corner. We dig out the old footing, set a new post deeper and wider, and remount the gate so it swings true. Post replacement runs $350 to $700 depending on depth, concrete, and whether we’re setting one post or rebuilding both sides. Fix the panel without the post and you’ll fix it twice.
Custom Welding
Naples has a lot of custom ornamental aluminum and wrought iron work, especially in Old Naples and Aqualane Shores. When an estate gate has a cracked weld, a broken picket, or a hinge plate that’s pulling away, we weld it in place. Our rig carries the equipment for on-site aluminum and steel welding, so the gate doesn’t leave your property. Custom welding for crack repair or bracket fabrication averages $150 to $400 per gate.
Why do gate hinges fail so much faster in Naples than in Fort Myers or inland Florida?
Because Naples sits directly on the Gulf, and the constant salt-laden air oxidizes ferrous hardware far faster than cities even 10 miles inland. Hinges that would last eight to ten years in Fort Myers often fail in two to three here. The fix is stainless steel or heavy-gauge galvanized hardware, not another set of zinc-coated hinges. Call (877) 610-2993 and we’ll match the hardware to your distance from the water.
After a lightning strike, my gate only opens halfway and the keypad entry doesn’t work. What needs replacing?
The operator control board and usually the keypad. Lightning surges travel through access control wiring and destroy boards even when the motor itself survives. A full gate operator control board replacement after a lightning strike runs $250 to $600 installed, board-dependent. We replace the board, test the motor and limit switches, and often recommend a surge protector on the AC input to keep the next storm from doing the same thing. Call (877) 610-2993 for a free estimate.
Brands We Service in Naples
We’re certified on nine major gate brands, and we stock parts locally for the ones Naples actually runs: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means a Viking board that lightning took out in July doesn’t wait on a truck from three states away. See our brands for the complete list.
Pricing for Gate Repair in Naples, FL
| Service | Typical range in Naples |
|---|---|
| Hinge and post repair | $250 - $600 |
| Electric gate repair (control board, photo eye) | $200 - $500 |
| Weld and rust repair | $150 - $400 |
| Manual single swing gate installation | $1,800 - $4,500 |
| Automated swing gate installation | $5,500 - $14,000 |
| Slide gate installation (high-cycle community) | $6,000 - $18,000 |
| Motor repair (capacitor, limit switch) | $185 - $340 |
| Full operator replacement (driveway swing) | $1,400 - $2,800 |
| Slide gate operator replacement | $2,500 - $4,500 |
| Keypad entry replacement | $350 - $650 |
| Phone entry system installed | $700 - $1,200 |
| Card reader replacement | $450 - $800 |
What pushes price up in Naples is proximity to the coast and the cycle count on your gate. A community entry gate that logs thousands of activations a week needs heavier-duty everything, and a gate within a mile of the Gulf needs stainless hardware where a zinc-coated part would fail in two years. Every price is quoted and agreed in writing before work begins. The quote is the price.
Neighborhoods We Serve in Naples
We run calls all across Naples from the Gulf-front estates to the communities out by Collier Boulevard. Typical response time in the city is same day for repair calls, and we answer the phone at 2 AM the same way we do at 2 PM.
- Port Royal and Aqualane Shores
- Pelican Bay and Bay Colony
- Grey Oaks and Mediterra
- Park Shore and the Moorings
- Old Naples (34102)
Service Area - Cities Near Naples
While this page focuses on Naples, our crews also cover the surrounding Collier County communities. If you’re just outside the city, see Golden Gate, FL, Naples Manor, FL, East Naples, FL, Naples Park, FL, or Pelican Bay, FL for details on your area. And if you’re in the city proper, Naples, FL is where to start. We coordinate dispatch from our South Florida office so a live person always knows where every truck is.
Serving Naples, FL - Our Local Coverage Area
Gatewood Fence & Gate crews serve Naples and the communities around it; dispatch is coordinated from our Miami (South FL) office. The map shows the Naples coverage area; if your address is on it, we can help.
Also serving nearby: Naples, FL, Golden Gate, FL, Naples Manor, FL, East Naples, FL, Naples Park, FL, Pelican Bay, FL.
FAQs About Gate Repair in Naples
Two things: the Gulf and the volume of gated communities. Salt air corrodes hardware two to three times faster than inland Florida, and lightning from June through September destroys operator boards at a rate you don’t see in Orlando or Tampa. Add the thousands of gated communities and HOAs, and Naples gate work is its own animal. Call (877) 610-2993 and we’ll come look.
For most repairs, no. For new gate installations, Collier County wind-load requirements apply, and your HOA may have its own approval process. We know the local code path and submit the paperwork before we install, not after. If you’re not sure what your gate needs, call (877) 610-2993 and we’ll tell you straight.
Yes, and that’s a big part of our spring and summer calendar in Naples. Snowbird owners in Pelican Bay and Park Shore leave properties unoccupied from May through October, and gates that sit dormant through the humid Gulf summer come back to seized hinges and moisture-damaged keypads. We work with property managers or a trusted neighbor to access the gate, and we’ll send photos and a written quote before any work starts. Call (877) 610-2993 to get on the fall schedule early.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Naples Customers Say
"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu