Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Marion
Gate Repair in Marion and installation runs $180-$340 for most keypad and remote fixes, and $1,200-$2,800 for a full keypad, intercom, and opener setup on a residential driveway gate. We get to Marion homes fast because we know the town’s layout: subdivisions off Highway 64, older lots near the courts and city park, and rural-edge properties along the Crittenden County fringe. If your gate keypad is dead, your remote won’t open the gate after an ice storm, or your video intercom rings but won’t release the latch, call (877) 610-2993 and a live person answers.
Marion’s soil is the problem nobody warns you about. The heavy Delta clay under this town swells every spring and shrinks every summer. That movement throws gate posts out of plumb, and when the post moves, the keypad, the photocell, the operator arm, and the card reader all start arguing with each other. Fixing the electronics without fixing the post is a callback waiting to happen. Hal Gatewood has been at this since 2001 because he learned early that a gate access control problem in Marion is usually a two-part job: the circuit board and the earth beneath the post.
We answer around the clock. Not a voicemail, not a chatbot. Call (877) 610-2993.
Why Gatewood Fence & Gate Is Marion’s Preferred Gate Access Control Company
Hal Gatewood started this shop in 2001, and his name is still on the door. That matters in Marion, where folks have seen national outfits quote one price on the phone and a different one at the driveway. Hal works on the principle that the person who answers your call should be the person who can actually fix your gate, or at least the person who knows exactly who is showing up and when.
Every job carries the 90-Day Done Right Promise in writing. If it’s not right, Hal comes back and makes it right. No runaround, no fine print. That promise is stamped on the invoice. For Marion homeowners who have been burned before, that piece of paper is worth more than any marketing slogan.
We hold a published address and a license number anyone can look up. Hal’s on-site welding means a gate stays in your driveway while it’s being repaired, not hauled to some shop across the river. And calls are answered by a live person 24/7. That’s not a perk. That’s the way a local business should run.
Our Gate Access Control Services in Marion
The Gate Access Control work we do in Marion spans six main areas. Here are the ones Marion homeowners call us about most, with the local reasons why.
Keypad Entry
Keypad entry systems fail in Marion most often because the post they’re mounted on has moved. A keypad that worked fine in December suddenly won’t accept the code in April. That’s not the keypad’s fault. The post heaved with spring rains, the gate’s strike plate shifted a half inch, and the latch won’t seat. We relevel the post first, then reprogram the keypad. Our Gate Installation in Marion for a new keypad typically runs $375-$750 depending on whether you want a stand-alone model or one tied into your opener and smartphone app.
Remote Control
Remote control failures in Marion fall into two buckets: electronics and physics. The electronics side is simple: dead batteries, lost transmitters, receiver boards fried by power flickers. The physics side is what makes this town different. When an ice storm loads a gate with weight, the operator arm bends, the limit switches drift, and suddenly the remote sends the signal but the gate only moves three inches. We stock common remotes and receiver boards for Linear, Viking, and Ghost Controls, and we can program a replacement remote on site. Typical remote reprogramming or replacement in Marion runs $95-$185 per transmitter.
Phone Entry
Phone entry, sometimes called cellular or dial-to-open, lets you buzz a visitor in from your cell phone or a landline. Marion homeowners with long driveways and gate posts set back from the house especially like these. The problem is that phone entry units rely on consistent cellular signal, and parts of Marion near the river can get spotty reception depending on your carrier. We’ll test signal strength before we sell you a unit. If it won’t hold a signal, we’ll tell you straight instead of installing something that works half the time. Phone entry units in Marion run $450-$950 installed.
Card Reader
Card reader and fob systems show up more at Marion’s businesses, churches, and shared driveway entrances than at single-family homes, but they’re practical for anyone with multiple drivers. Card readers fail less often than keypads, but the readers mounted on gate posts suffer the same fate: when the post tilts, the card swipes weirdly or the reader’s angle drifts so it won’t read at all. We service and install card readers from DoorKing and Linear, with typical Marion installations at $600-$1,400 including the reader, controller, and wiring.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Marion
We are certified to service nine major gate brands, and in Marion we see a lot of Viking and Linear openers on the newer brick-front subdivisions, plus Ghost Controls on DIY-style retrofit jobs that need professional help with a Gate Motor & Opener - Marion. We keep common parts for Viking, Linear, and Ghost Controls on the truck, which means faster turnaround when your opener stops responding. If a DoorKing unit fails and the board needs replacing, we can usually have that ordered and installed within a week. On-site welding comes with us on every call, so a cracked operator bracket gets fixed in your driveway instead of being shipped off.
Common Gate Access Control Problems We See in Marion Homes
- Clay heave tilts the post, which kills the keypad. Marion’s expansive Delta clay swells with spring rain and shrinks in summer drought. That cycle tilts gate posts out of plumb, so the keypad’s latch alignment drifts, the code won’t engage, and the homeowner thinks the keypad died. It didn’t. The post moved.
- Ice storms bend the operator arm and confuse the remote. A solid ornamental iron gate loaded with ice weighs hundreds of extra pounds. The opener arm bends, the limit switches lose their settings, and the remote sends a signal but the gate only nudges a few inches. We reset the arm, reprogram the limits, and weld any cracked joints before we leave.
- Rusted hinge bearings make the opener grind but the gate barely swings. Mid-South humidity is brutal on iron gate hardware. Hinge post bearings seize with rust, so the opener motor strains, the safety sensor eventually trips, and the whole system locks up. We remove the gate, free the bearings or replace them, and rehang it before touching the electronics.
- Safety photocells misalign and the gate reverses mid-cycle. When one post heaves and the other doesn’t, the photocell beam that runs between them breaks. The opener interprets that as an obstruction and refuses to close, or reverses halfway. Newer Marion subdivisions built on former Delta farmland with minimal soil prep see this on gates only five to seven years old.
Pricing for Gate Access Control in Marion, AR
Here’s what Marion homeowners can expect, line by line:
- Keypad replacement or reprogramming: $180-$340
- Remote programming or replacement: $95-$185 per transmitter
- Phone entry unit installed: $450-$950
- Card reader installation: $600-$1,400
- Video intercom installation: $800-$2,200
- Operator arm repair or replacement: $220-$520
- Full driveway gate access control system: $1,200-$2,800
These are honest ranges, not teaser prices. What moves the number up is post work: if the post needs releveling, re-footing, or re-pouring, that’s the difference between a $250 keypad job and one that runs closer to $600. The price is quoted and agreed before any work starts, and we never change it at the door. Free estimates on any written quote. Seniors and veterans get 10% off, permanently. Call (877) 610-2993.
We Also Serve Cities Near Marion
If you’re across the river or just down the road, our crews cover Gate Access Control in Marion and reach West Memphis the same day in most cases. Scheduling is coordinated from our Memphis office, but the people who show up are local to Crittenden County and know the soil, the weather, and the gates.
Serving Marion, AR - Our Local Coverage Area
We’re based in the Marion area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Marion
Your gate post is heaving with the spring rains. Marion sits in the Mississippi River alluvial floodplain, and the Delta clay under this town expands when saturated. The post tilts, the keypad’s latch alignment drifts, the photocell beam breaks, and the opener refuses to move. The fix starts with releveling and re-footing the post, then reprogramming the electronics. Call (877) 610-2993 and we’ll dig it out and do it right.
The operator arm is likely bent, and the limit switches are off. Ice storms load a gate with hundreds of extra pounds, the arm absorbs that weight, and the opener’s brain no longer knows where the fully-open and fully-closed positions are. The gate moves a few inches, trips the safety, and stops. We straighten or replace the arm, reprogram the limits, and weld any cracked joints before we test the remote again.
Yes, and you should if the gate is stuck closed and you need to get a vehicle out. Most residential swing and slide gate openers have a manual release handle or key located on the operator arm or motor housing. Turn the opener off at the breaker or its power switch, then pull the release lever to disengage the motor and push the gate manually. If the post has heaved and the gate won’t swing freely by hand, don’t force it. That’s a job for a professional, because a gate that binds from a tilted post can pinch or drop unexpectedly. Call us at (877) 610-2993 if you’re unsure.
Check the gap between the gate and the strike plate. If the gap is visibly wider or narrower than it used to be, or if the gate doesn’t hang level, the post has moved and the keypad isn’t your problem. If the gap looks right and the keypad’s screen or backlight won’t come on at all, that’s likely a power or keypad issue. Either way, we can tell you in person. Estimates are free.
Probably not. Video intercom failures are usually about the relay that sends the open signal to the opener board, or a lost network connection between the intercom and your Wi-Fi. Soil movement typically affects the physical gate, not the app. But soil can be a factor if the gate post has tilted enough that the opener’s safety circuit prevents the gate from moving even when the app sends the signal. We’ll test the relay, the network, and the post, and fix whichever one is actually broken.
We were called to a brick-front subdivision off Highway 64 in Marion after a winter ice storm. A Viking swing gate operator had bent its arm and pulled the hinge post two inches out of plumb, tripping the safety photocell. Our crew dug out the old post footing, re-poured with deeper concrete, rehung the gate, then reprogrammed the keypad entry and retested the loop detector before the homeowner’s next trash pickup. That’s a standard Marion repair for us, because the soil here doesn’t forgive shallow footings.
If your gate access control system in Marion isn’t working, or you’re tired of reprogramming the same keypad every spring, call (877) 610-2993. A live person answers, day or night. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Marion and Crittenden County since 2001.