Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Edmonds
Most gate access control failures in Edmonds aren’t random. Salt air off Puget Sound eats mild-steel hardware in three to five years, and the bluff terrain shifts post footings every wet season, throwing gates out of alignment. That combination means keypad dropouts, reversing gates, and dead control boards happen here more than in Lynnwood or Brier. We fix the actual cause, not just the symptom, and we answer the phone around the clock at (877) 610-2993. Hal Gatewood has been doing this since 2001, and his name is on every job.
Why Gatewood Fence & Gate Is Edmonds’s Preferred Gate Access Control Company
We’re the local shop that repairs what other companies want to replace. When a Viking keypad stops reading codes on a bluff-top home in the Edmonds Bowl, we trace the problem back: corroded hinge, sagging post, pinched photocell beam. We weld on site, in your driveway, so the gate never leaves your property. The 90-Day Done Right Promise is stamped in writing on every invoice. If it’s not right, one call brings Hal back. No runaround.
Edmonds customers across 98020 and 98026 call us because we show up when we say we will, and we quote a price before any work starts. A live person answers every call, 24/7. Not a voicemail. Not a call center. You can drive to the shop and look Hal in the eye if you want. That is the oldest accountability there is.
Our Gate Access Control Services in Edmonds
We handle the full range of Gate Access Control work, from retrofitting a 1960s swing gate to wiring a modern video intercom on a new cedar privacy gate off Olympic View Drive. Here is what Edmonds homeowners ask for most.
Keypad Entry
Keypad failure in Edmonds is rarely the keypad itself. Salt air corrodes the wiring connections and the hinge hardware, which drops voltage or shifts the gate enough to bind the latch. We test the whole circuit before replacing anything. A typical keypad repair or replacement in Edmonds runs $220-$490, and retrofitting a new keypad to an older Viking or Ghost Controls operator usually adds an hour of labor because the legacy wiring needs re-termination.
Remote Control
When a remote stops working on a gate near the ferry dock, we check receiver corrosion first. Marine air gets inside the receiver housing and eats contacts. Replacement remotes run $45-$95 each in Edmonds, while a new receiver board runs $180-$320. We program everything on site and test it from your car, not from the shop bench.
Phone Entry
Phone entry systems let you buzz a visitor in from your cell, and they make a lot of sense on Edmonds properties with long driveways or bluff-top approaches where you can’t see the gate from the house. A new phone entry controller in Edmonds typically runs $450-$850 installed, depending on whether we can reuse your existing wiring or need to pull new low-voltage line. We can often retrofit these to pre-2000 operators if the control board still has dry-contact inputs.
Card Reader
Card readers are common on multi-home driveways and small HOAs in Edmonds. Wiegand and proximity readers both work fine here, but we recommend stainless hardware within a few blocks of the water. A single-door card reader installation runs $380-$700 in Edmonds, including programming. We stock readers compatible with DoorKing, Elite, and Linear controllers, so turnaround is usually same-week.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Edmonds
We’re certified to service nine major gate brands, and for Edmonds work we most often see Viking, Ghost Controls, and DoorKing on older residential systems. Elite shows up on some of the newer 98026 installs. We keep common parts for these brands on the truck, so a keypad repair in Edmonds doesn’t wait on a freight shipment from Ohio. If your operator is older than 2000 and the board is dead, we’ll tell you honestly whether a retrofit is worth the money or a replacement operator is the cheaper five-year answer.
Common Gate Access Control Problems We See in Edmonds Homes
- Keypad codes dropping out every few years. This is almost always the control board or wiring corroding from salt air. We replace the board, re-terminate the wiring with sealed connectors, and the problem stays fixed. Re-coding the keypad alone just buys you one more winter.
- Gate reverses when it’s half open. The entrapment sensor is tripping because the gate has sagged out of alignment. On Edmonds bluff lots, the post footing shifts every wet season. We re-level the post, re-hang the gate, and the sensor stops false-triggering.
- Keypad works but the gate won’t move. That’s usually a thermal overload in the motor from fighting corroded hinges. We free the hinges or replace them with hot-dip galvanized units, then reset the operator. If the board has burned traces, we replace it.
- Older swing gate with no photocell or edge sensor. Pre-2000 gates in the Edmonds Bowl often lack modern safety devices, and the salt air has corroded the hinges so badly the motor can’t push the gate. We add a safety photocell, replace the hinges, and bring the system up to current code before re-tuning the operator.
Pricing for Gate Access Control in Edmonds, WA
Here are the ranges we actually quote in Edmonds. A keypad repair or replacement typically runs $220-$490. A new phone entry controller runs $450-$850. A card reader install runs $380-$700. A full access control retrofit, where we replace the control board, add a safety photocell, and re-hang the gate with galvanized hardware, typically lands between $900 and $1,600 depending on gate size and how much welding is needed. Salt air damage near the waterfront pushes materials toward stainless or hot-dip galvanized, which adds 15-25% to hardware cost but eliminates the two-year callback. Every job is quoted and agreed before we start. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Edmonds
We handle Gate Access Control in Edmonds and the surrounding communities. If you’re in Mountlake Terrace, Lynnwood, Alderwood Manor, or Brier, the same crew and the same 90-Day Done Right Promise apply. Response time to those areas is typically the same day or next morning, depending on where we are in the rotation.
Serving Edmonds, WA - Our Local Coverage Area
We’re based in the Edmonds area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Edmonds
Salt air from Puget Sound corrodes the wiring connections and control board inside the operator housing. The keypad itself is usually fine. We replace the corroded board, seal the connections, and in waterfront areas we recommend stainless or hot-dip galvanized hardware so the repair lasts more than three years. Call (877) 610-2993 and we’ll diagnose it on site.
It’s usually not the access control board. On Edmonds bluff lots, the post footing shifts with seasonal rain saturation, the gate sags, and the safety photocell beam gets pinched or misaligned. The sensor tells the operator to stop and reverse for safety. We re-level the post, re-hang the gate, and the reversing stops. The board only needs replacement if it’s burned out from repeated overload trips.
Yes, in most cases we can. The 1970s operator has to have dry-contact inputs or a replaceable control board. If it does, we wire the phone entry controller into the existing circuit and you get full remote access without replacing the whole gate system. If the board is too far gone, we’ll tell you and quote a replacement honestly. Call (877) 610-2993 for a free assessment.
Yes. Properties within a few blocks of the ferry terminal see standard mild-steel hinges fail in three to five years because the salt-laden marine air accelerates corrosion. Stainless or hot-dip galvanized hinges cost more up front but eliminate the callback. We recommend the upgrade on every waterfront-facing repair in Edmonds, and we will show you the difference before we install it.
If the motor is still strong and the gate frame is solid, a new control board for $300-$500 usually extends the life another five to eight years. If the motor is also fighting corroded hinges and a sagging post, you’re likely better off with a full retrofit, which runs $900-$1,600 in Edmonds. We’ll test the motor and give you a straight answer. Replacement versus repair is always your call, with a written price before we start.
Contact Gatewood Fence & Gate in Edmonds
If your gate access control is acting up in Edmonds, call (877) 610-2993 and describe what it’s doing. A live person answers. We’ll schedule a time, show up, diagnose the actual cause, and quote a fixed price before any work starts. Hal Gatewood’s name is on the shop, the invoice, and the 90-Day Done Right Promise. That’s how it’s been since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Edmonds and surrounding communities since 2001.