Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Pembroke Park, FL
Gate repair in Pembroke Park usually means one of two things: a community entrance gate serving dozens or hundreds of residents has gone down, or a commercial slide gate off US-1 has seized up from salt air. Most of the town’s gates are original installations from the 1970s and 1980s, which means we’re fixing legacy operators, corroded hardware, and settled posts more than we’re swapping parts on new systems. Call (877) 610-2993 and a live person answers, any hour, every day.
Why Pembroke Park Homes Are Different
Pembroke Park sits two to three miles from the Atlantic, and that proximity shows up in every gate we open. Salt-laden air gets into rollers, hinge pins, track brackets, and control board terminals noticeably faster here than ten miles inland. We regularly pull apart hinge assemblies on community entrance gates and find the grease washed out and the steel pitted from years of coastal exposure. Then there’s hurricane season. A strong storm will bow an aluminum frame, shove a slide gate off its track, or fry a control board with a surge, all at once. After a big storm, those calls stack up fast.
The housing stock defines this town more than anything else. Pembroke Park’s residential fabric is dominated by mobile home and manufactured housing communities built in the 1960s through 1980s, and each one relies on a single entrance gate as its primary security checkpoint. That gate cycles hundreds of times a day, every day. Along the US-1/Federal Highway corridor, older warehouse and light-industrial properties run aging slide gates protecting loading areas and storage yards. These aren’t decorative gates. They’re working equipment, and they need the kind of repair work that respects how hard they get used.
Gate Repair in Pembroke Park
Gate repair in Pembroke Park is different from gate repair anywhere else in Broward County because the equipment skews older and the cycle counts run higher. Many mobile home park entrance gates still run on Linear or Eagle operators installed when the parks were first built, and most companies won’t touch those units anymore. We do. We stock legacy parts, we reprogram discontinued boards, and we repair in place rather than quoting a full replacement when the gate still has life in it. If your community entrance gate off Hallandale Beach Boulevard is stuck mid-travel, or a swing gate on US-1 won’t close, call (877) 610-2993. A live person answers.
Electric Gate Repair
Electric gate repair in Pembroke Park usually means one of two things: an operator that has lost its mind, or wiring that has given up after years of salt air and humidity. We service nine major brands including FAAC, BFT, Linear, and Viking, and we keep components on the truck for the legacy models still running in the town’s older communities. If your gate opens but won’t close, or closes but won’t latch, the problem is almost always in the control board, the loop detector, or the limit switch. We find it and fix it.
Electric gate repair here typically runs $200 for a simple fix up to $900 for a legacy board swap and reprogramming, depending on what failed and how much programming the old unit needs.
Automatic Gate Repair
Automatic gates in Pembroke Park see cycle counts that would kill a residential gate in most other cities within a year. When a single entrance serves 400 homes, that operator runs hundreds of cycles a day, and the mechanical side wears accordingly. We rebuild the mechanical side, the electrical side, and the safety side: photo eyes, loop detectors, edge sensors, and keypads. If your gate used to work on a keypad and now only responds to the remote, the fix is usually faster than you would think.
Full operator replacement with a new LiftMaster or BFT unit runs $1,400 to $3,800 installed, including the safety edge retrofits that older systems need to meet current UL 325 standards.
Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that’s where we start. In Pembroke Park, the soil is sandy and low-lying, and original post footings poured in the 1970s are often undersized or failing after decades of daily cycling. We dig out the old footing, set the post properly in new concrete, and rebuild the hinge in place. We weld on site, so the gate stays in your driveway. If the post is rotted at the base from salt air, we’ll show you the rot before we replace anything.
A hinge and post repair in Pembroke Park typically runs $350 to $700 depending on whether we’re rebuilding one hinge or resetting a full post in fresh concrete.
Gate Realignment
Slide gates off Federal Highway and swing gates in the mobile home parks drift out of alignment for predictable reasons: worn rollers, settled posts, and bent tracks from years of trucks and cars. We realign the gate in its existing hardware when it’s salvageable, and we tell you straight when it’s not. A slide gate that grinds against its track is chewing through rollers and motor torque. The longer it runs misaligned, the more expensive the repair gets.
Gate realignment on a slide or swing gate in Pembroke Park usually lands between $250 and $500, and we’d rather catch it early than watch you pay for a new operator later.
For more on how we approach this work, see our Gate Repair service page.
Can you still repair a 1970s Linear or Eagle gate operator at our Pembroke Park mobile home community, or do we have to replace it?
Yes, in most cases we can repair it. We keep Linear and Eagle replacement parts on the truck: control boards, pinion gears, rack sections, loop detectors, limit switches, and rebuild kits for the exact models spec’d into Pembroke Park’s mobile home parks during the 1970s and 80s. When replacement genuinely makes more sense, we’ll tell you that too. Call (877) 610-2993 for a straight answer.
Why does our swing gate by US-1 sag at the hinge post instead of the middle?
Because the hinge post is where the weight concentrates, and in Pembroke Park’s sandy, low-lying soil, the original footing from decades ago is often undersized or failing. Salt air also corrodes the base of the post where it meets concrete. When the hinge post leans, the gate sags at the latch end and the operator strains on every cycle. We reset the post in fresh concrete and rebuild the hinge in place.
Gate Installation in Pembroke Park
Gate installation in Pembroke Park runs $2,400 to $7,500 for a typical driveway or community entrance gate, depending on whether you need a new post, track, operator, or full welded frame. Most jobs are scheduled within five to seven business days, and we always confirm a firm written price before any work starts. If you live in a mobile home community off Hallandale Beach Boulevard or along the US-1 corridor, we know the gates you’re dealing with and the HOA approval process that goes with them.
Sliding Gate Installation
Sliding gates are the workhorse of Pembroke Park’s mobile home communities and the industrial properties along US-1. They need less setback than swing gates, which matters when the entrance is tight against a fence line or a canal. We set concrete footings for the track, install galvanized rack and V-wheel hardware, and mount operators from brands we actually stock parts for.
A sliding gate for a community entrance runs $3,500 to $7,500 depending on width, track length, and whether you need a new post footing or a retrofit.
Swing Gate Installation
A swing gate sags in the hinge post, not in the middle of the panel, and that’s where we start. In Pembroke Park, many existing swing gates are decades old and the hinge posts have shifted or rotted at the base from salt air. We check the post before we hang the gate, which saves you from a panel that binds against the operator six months later. For double swing gates at wider entrances, we synchronize both leaves so they close without slamming.
A single swing gate with one operator runs $2,400 to $4,800 installed, including the post work if it’s needed.
Security Gate Installation
Security gates for Pembroke Park HOAs and commercial properties usually mean more than a barrier. They include keypad access, intercom wiring, loop detectors for exiting vehicles, and safety photocells that prevent a gate from closing on a car or pedestrian. We’re certified on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the operator brand you already have isn’t a mystery to us. And we’ll be honest if a simple repair beats a full install.
Retrofitting an existing slide gate with a new operator and safety edge system runs $1,800 to $3,200, which is often the right move for parks on a tight budget.
See our Gate Installation page for details on how we spec and build these systems.
Does Pembroke Park require architectural approval before installing a new gate in an HOA community?
Yes, most Pembroke Park mobile home and manufactured housing communities require architectural committee approval before any gate installation begins, and skipping it leads to costly rework or resident access disputes. We’ve done enough of these that we can help you put together the height, finish, and automation specs your board will actually approve. Call (877) 610-2993 and we’ll walk you through it.
How does salt air in Pembroke Park affect a new automatic gate installation?
Salt air two to three miles from the Atlantic accelerates corrosion on standard rollers, tracks, hinges, and operator housings, so we spec galvanized or stainless hardware and powder-coated frames for installations in Pembroke Park. Standard bare steel that works fine in inland Broward fails noticeably faster here. It costs a little more up front and saves you a lot over the life of the gate.
Gate Motor & Opener in Pembroke Park
Gate motor repair in Pembroke Park typically runs $180 to $390, and most slide or swing gate opener jobs at local mobile home communities can be handled same day. If you manage an HOA entrance gate off Hallandale Beach Boulevard or a warehouse slide gate along US-1, you need someone who answers the phone and shows up. That’s us. We work on the legacy Linear and Eagle operators that dominate this town’s older parks, and we repair rather than replace whenever the repair will hold.
Motor Repair
Most motor repairs in Pembroke Park fall between $180 and $390. That covers limit switch replacement, capacitor failures, gear wear, control board diagnostics, and photocell realignment. We do on-site welding, so we can repair a cracked gate frame or a torn hinge post without hauling the gate to a shop. If a previous repair left sloppy welds or misaligned tracks, we’ll point it out. We get genuinely annoyed when we find work somebody else botched.
Linear Motor Service
Pembroke Park’s older mobile home parks still run on Linear operators from the 1980s, and we service those every week. Discontinued boards, worn rack and pinion sets, failed relays. We source matching legacy parts and reprogram rather than quoting a $2,500 replacement for a $200 repair. Park managers on tight HOA budgets keep our number in their office.
Legacy Linear board replacement with reprogramming runs $200 to $450, which is why repair beats replacement on these older units most of the time.
Slide Motor Service
Slide gates are common along US-1 and the warehouse rows in Pembroke Park. Salt air corrodes the rollers and the track, which makes the motor work harder until the gear strips or the board burns out. We check the chain tension, track level, and limit travel on every slide job, because if the track sags, a new motor won’t fix the problem.
A typical slide motor repair here runs $250 to $480, while a full slide operator replacement with battery backup is $1,200 to $3,200 depending on the gate’s weight and length.
For more detail on how we approach these repairs, see Gate Motor & Opener.
Can you repair an old Linear or Eagle gate operator without replacing the whole system?
Yes, and that’s most of what we do in Pembroke Park. We stock legacy Linear and Eagle gear sets, limit switches, relays, and discontinued control boards, and we can reprogram older units on site. If a park manager is told the only option is a $2,500 replacement, they should get a second opinion from us. Our second opinions are free on any written estimate.
What should we do if our community gate is stuck open after a hurricane?
Call us immediately. A stuck-open gate is a security problem for the whole park. After storms, we see warped aluminum frames, knocked-out hinge posts, and fried control boards all through Pembroke Park. We respond as an emergency, straighten and weld the frame on site, replace the board if needed, and get the gate closing again. A live person answers 24/7 at (877) 610-2993.
Gate Access Control in Pembroke Park
Gate access control in Pembroke Park usually means one of two jobs: putting a new keypad, intercom, or phone entry system on an existing community gate, or getting an older system working again after salt air and daily cycles have taken their toll. If you live in or manage one of the mobile home parks along Southwest 30th Avenue or the warehouse rows off US-1, you already know how fast a gate issue turns into a line of cars at 5 p.m. We stock parts for the legacy systems this town runs on and we program them on site.
Keypad Entry
A keypad at a Pembroke Park community entrance takes more abuse than most people realize: direct sun, afternoon thunderstorms, and hundreds of codes punched every day. We install and service stand-alone keypads and keypads tied into larger access systems. If the buttons have gone soft or the housing is full of ants, we can usually replace the unit the same day for most gate models.
A basic keypad replacement in Pembroke Park runs roughly $180 to $420 depending on brand and whether it’s a stand-alone unit or tied into a larger board.
Phone Entry
Phone entry systems at Pembroke Park gates connect a visitor at the keypad to a resident’s phone line to open the gate. Aging phone entry boards in this town often fail after years of humidity and lightning. We service, reprogram, and replace phone entry systems, and we know how to work with the older panels still common in the mobile home communities along Pembroke Road.
A phone entry system repair typically lands between $250 and $650, while a full phone entry replacement can run $900 to $1,800 depending on the panel and wiring condition.
Card Reader
Some Pembroke Park warehouses and mobile home parks run proximity card readers at their slide gates. We install, wire, and program card readers for staff, vendors, and residents. If you have an old reader that is no longer reading cards reliably, we can often swap just the reader head and leave the rest of the system alone, which keeps the job reasonable and quick.
Card reader installs start around $400 for a basic single-door reader with wiring and programming done on site.
For a deeper look at what we install and service, see Gate Access Control.
How quickly can you get to Pembroke Park for a gate access emergency?
We can usually have someone in Pembroke Park the same day for an access control failure, especially if a community gate is stuck open or stuck closed. A live person answers the phone 24/7 at (877) 610-2993, so we can get the details while you’re standing at the gate. Call us, and we’ll give you a straight answer about arrival time.
Does the 90-Day Done Right Promise apply to access control work in Pembroke Park?
Every access control job we do in Pembroke Park carries the 90-Day Done Right Promise in writing. If a keypad, phone entry board, or card reader we serviced fails within 90 days, one call brings us back. The promise is printed on the invoice, not hidden on a website. Call (877) 610-2993 for any follow-up, and we’ll make it right.
Gate Parts & Welding in Pembroke Park
When a community entrance gate in Pembroke Park grinds to a halt, every resident behind it feels the problem. Gate parts fail under daily use, salt air, and age. And here, where much of the town lives behind a single entry point built decades ago, a gate that won’t close is an open door off Federal Highway. We repair and weld gate hardware on site across Pembroke Park, usually within the same day you call.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. On swing gates throughout Pembroke Park, especially the wide entrance gates at older manufactured home communities, the original hinge welds crack under decades of daily cycling. We remove the old hardware, weld in new heavy-gauge hinges, and set the gate so it swings true. Not patched. Rebuilt.
Hinge replacement on a standard residential swing gate runs $180 to $320 per hinge, including the new hardware and on-site labor.
Post Replacement
Wind from a hurricane, a delivery truck clip, or just 40 years of rust at the base. When a post in Pembroke Park fails, the gate goes with it. Our crew digs out the old footing, sets a properly sized post in concrete, and welds or bolts the gate back to it. We see post failures more often in the low-lying mobile home parks near Southwest 33rd Street, where ground moisture moves through the sandy soil and eats steel from below.
Post replacement for a single gate post, including concrete and setting, runs $350 to $650 depending on post size and the condition of the existing footing.
Rail Repair
Slide gates run on a track, and that track takes a beating from salt air and the gravel that collects on the industrial lots along Pembroke Road. We repair bent rails, weld cracked joints, and replace rollers so the gate glides instead of shuddering. On the older slide gates protecting warehouse loading areas, we often find the rail has never been adjusted since installation. We fix that.
Rail repair on a slide gate runs $220 to $480, with roller replacement typically $35 to $75 per roller depending on the hardware your track uses.
Custom Welding
Sometimes the right part doesn’t exist anymore. That’s where on-site welding earns its keep. We fabricate brackets, reinforce corners, extend leafs, and rebuild gate frames in Pembroke Park driveways and parking lots without hauling the gate off to some shop. If a park manager needs three matching gates repaired the same week, we handle that too, welding on site so the community’s one entrance isn’t left unguarded overnight.
Custom welding is quoted by time and materials, with most small fabrication jobs landing between $150 and $400.
For more on what we can build and fix, see Gate Parts & Welding.
Do you weld on site in Pembroke Park, or do you take the gate to a shop?
We weld on site in Pembroke Park driveways, parking lots, and community entrances. That keeps your property secure and saves you the cost of hauling a gate across town. Hal’s truck carries the welder, the steel, and the hardware needed for most jobs. The gate stays where it belongs, and the repair happens in place.
Can you repair the old gate operators at Pembroke Park’s mobile home communities?
Yes, and we do it regularly. Many of Pembroke Park’s manufactured home communities still run on legacy operators from Linear and other brands installed decades ago. We stock parts for discontinued units and repair rather than replace whenever the repair will hold. For more involved electrical diagnostics, our gate repair service covers that side too.
Brands We Service in Pembroke Park
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock legacy parts locally for Linear and Eagle operators still running in Pembroke Park’s older mobile home communities, which means most repairs here don’t wait on a supplier. See our brands for the full rundown.
Pricing for Gate Repair in Pembroke Park, FL
| Service | Typical range in Pembroke Park |
|---|---|
| Electric gate repair | $200 - $900 |
| Hinge and post repair | $350 - $700 |
| Gate realignment | $250 - $500 |
| Motor repair | $180 - $390 |
| Slide motor repair | $250 - $480 |
| Full operator replacement | $1,400 - $3,800 |
| Swing gate installation | $2,400 - $4,800 |
| Sliding gate installation | $3,500 - $7,500 |
| Keypad replacement | $180 - $420 |
| Phone entry repair | $250 - $650 |
| Hinge replacement (per hinge) | $180 - $320 |
| Post replacement | $350 - $650 |
What pushes a price up in Pembroke Park is usually the age of the equipment and the condition of the post footings, which settle in the sandy soil over decades. The price we quote before starting is the price you pay: written, agreed, and backed by the 90-Day Done Right Promise.
Neighborhoods We Serve in Pembroke Park
Pembroke Park is compact, and we cover all of it. Same-day response is typical for repair calls, with community entrance gates prioritized when they’re holding up hundreds of residents.
- Mobile home communities along Southwest 31st Avenue
- Hallandale Beach Boulevard corridor
- Federal Highway industrial strip
- Pembroke Road commercial area
- Warehouse rows off US-1
Service Area - Cities Near Pembroke Park
We work throughout southern Broward and northern Miami-Dade, including Hallandale Beach, FL, Pembroke Park, FL, Aventura, FL, North Miami Beach, FL, Ojus, FL, and Sunny Isles Beach, FL. If your gate is down and you’re not sure whether we cover your street, call (877) 610-2993 and ask.
Serving Pembroke Park, FL - Our Local Coverage Area
Gatewood Fence & Gate crews serve Pembroke Park and the communities around it; dispatch is coordinated from our Miami (South FL) office. The map shows the Pembroke Park coverage area; if your address is on it, we can help.
Also serving nearby: Hallandale Beach, FL, Pembroke Park, FL, Aventura, FL, North Miami Beach, FL, Ojus, FL, Sunny Isles Beach, FL.
FAQs About Gate Repair in Pembroke Park
Most Pembroke Park repair calls are handled same day, and a community entrance gate that’s stuck open or closed gets priority because it affects hundreds of residents, not one house. A live person answers 24/7 at (877) 610-2993 and will give you an honest arrival window before you hang up.
Most manufactured home communities in Pembroke Park require board or management company sign-off before gate hardware changes, especially if the operator, gate style, or finish changes. We provide the spec sheets and dimensions your management office asks for so the submittal goes through without back-and-forth. Call (877) 610-2993 and we’ll help you prepare it.
Yes. We work the mobile home communities off Southwest 31st Avenue and Hallandale Beach Boulevard, the commercial properties along Pembroke Road, and the warehouse slide gates on the Federal Highway industrial strip. One call to (877) 610-2993 covers all of Pembroke Park with no trip charge inside the county.
Call (877) 610-2993 for a free estimate on any gate repair, installation, motor, access control, or welding job in Pembroke Park. We answer live, we quote before we work, and the name on the invoice is the name on the shop.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Pembroke Park Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg