Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Brentwood
Gate installation in Brentwood usually runs $2,400-$6,800 for a new automated driveway gate, depending on whether you need a swing, slide, or double gate, the length of track or post work involved, and whether we’re replacing an operator or starting from scratch on fresh concrete. Most Brentwood jobs take one to two days once materials are on hand, and every estimate is quoted and agreed before any work starts. Hal Gatewood has been doing this since 2001, and the person who shows up to measure your driveway off Balfour Road or Sand Creek Road will be someone whose name you can verify. Call (877) 610-2993 for a free estimate.
Why Gatewood Fence & Gate Is Brentwood’s Preferred Gate Installation Company
Brentwood isn’t a generic suburb, and gates here don’t fail like they do in Walnut Creek or Danville. The 2000s-era master-planned communities that line the Balfour Road and Sand Creek Road corridors were built fast, with ornamental iron swing and slide gates standardized across whole tracts. That means the hardware is consistent, but it also means the operators are all roughly the same age and hitting end-of-life around the same time. We know which HOA monument gates in 94513 use Viking or Linear operators, and we know which neighborhoods have loop detector wire corroding in the agricultural Delta soil beneath them.
Our crew has been called back to Brentwood streets again and again because homeowners here talk. When a neighbor’s gate stops opening and we fix it the same day, the guy across the street calls next week. That’s how a local business should work. We’re insured and bonded, and Hal Gatewood’s name is on every invoice. If a job isn’t done right, the 90-Day Done Right Promise means one call brings him back, no runaround.
Our Gate Installation Services in Brentwood
We install and replace the full range of residential and HOA gates across Brentwood, and we do it with a repair-first mindset. If a post is solid and the gate is square, we’ll tell you. If the post is rotted at the base and the gate is sagging, we’ll tell you that too, and then we’ll fix it properly. Here’s what we handle most often in Brentwood.
Driveway Gate Installation
New automated driveway gates in Brentwood typically run $3,200-$6,800 installed, including the gate frame, operator, safety edges, and programming. Homes built in the 1998-2008 boom years often already have the gate structure but need the operator replaced, which lands closer to $900-$1,700 depending on brand and horsepower. We’ll tell you whether your existing posts can support a new gate, or whether the Delta soil moisture means it’s time to pour new footings.
Pedestrian Gate Installation
Pedestrian gates in Brentwood are simpler but not trivial. A standard ornamental iron walk gate runs $600-$1,400 installed, and we match the existing fence height and style so it doesn’t look bolted-on. These gates take a beating from the afternoon Delta breeze funneling through the Altamont Pass, so we use heavier-gauge hinges and stainless fasteners here as a matter of course. Shows in five years when the neighbor’s gate squeaks and yours doesn’t.
Sliding Gate Installation
Sliding gates are the workhorse of Brentwood’s wider lots and side-yard entries. Expect $3,800-$7,500 for a new automated slide gate with track, cantilever roller hardware, and operator. The persistent Delta winds put lateral load on these gates year-round, which is exactly why rack and pinion adjustments matter more here than in calmer Bay Area towns. We also see a lot of loop detector wire failures in 94513, where the agricultural delta soils retain moisture and corrode buried wire years ahead of schedule. A new slide gate without addressing the loop is just a sticking point waiting to happen.
Swing Gate Installation
Swing gate installation in Brentwood runs $2,400-$5,500 for a single residential gate, and $4,500-$8,200 for a double gate with two leaves and a high-cycle operator. The 100°F+ summers here make steel frames expand and bind against posts and latch strikes, so we set clearances wider than the factory spec and use operators with thermal overload protection. That’s not a guess; it’s what keeps a Brentwood gate opening in July when the thermometer hits 104.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Brentwood
We’re certified to service and install nine major gate brands, including Viking, Linear, and DoorKing, and we keep a rolling stock of common parts in the truck so a Brentwood job doesn’t stall waiting on a courier from a warehouse in Sacramento. The 2000s-era HOA monument gates around Balfour Road and Sand Creek Road used a lot of Viking and Linear operators, so we’ve rebuilt enough of them to know their failure patterns cold. If your operator is beyond saving, we’ll quote a replacement from the same brand or a better fit for your specific gate weight and wind exposure, and that price is agreed before we order a single part.
Common Gate Installation Problems We See in Brentwood Homes
- Hinge posts rotted at the base. The Delta soils under much of 94513 hold moisture like a sponge, and when irrigation runoff pools around a gate post, the base rots from the inside. The gate sags, drags against the latch strike, and the operator motor works against a load it was never sized for. Fix the panel without the post and you’ll fix it twice.
- Ornamental iron gates binding in summer heat. Brentwood regularly hits triple digits in July and August, and steel expands. A gate with factory-tight clearances will bind against its posts and ground hardware when the thermometer climbs, which is why our installation specs account for the thermal range out here.
- Vehicle loop detectors failing early. The buried wire loop that tells your gate operator when a car is waiting corrodes in the moisture-heavy agricultural soils common under Brentwood’s master-planned communities. When that loop fails, the gate won’t open for your car or stays open for no one. We replace loop wire with moisture-rated poly-lined cable and seal the saw cuts.
- Wind-load fatigue from the Delta breeze. The same wind that supports the Altamont wind farm pushes against gate leaves all afternoon, every afternoon. That constant load wears hinges, stresses welds, and makes operators work harder than their duty cycle rating assumes. We size hardware for the wind, not just the gate.
One Brentwood job that sticks with us: a double swing gate on a stucco tract home off Sand Creek Road where the hinge post had rotted at the base from irrigation runoff and Delta soil moisture. The gate dragged hard against the latch strike every time the wind kicked up. We cut out the old post, poured a deeper footing with stainless anchor bolts, and installed a LiftMaster operator with a new loop detector and safety photocells. Then we walked next door and adjusted the rack and pinion on the neighbor’s slide gate, because the same HOA’s loop wire had shorted from the same corrosion. Two gates, same block, same root cause.
Pricing for Gate Installation in Brentwood, CA
You won’t get a phone quote that changes at your front door. The price we quote is the price on the invoice, and it’s agreed before any work begins. Here’s what Brentwood homeowners can expect for the most common installations:
- Pedestrian gate: $600-$1,400
- Operator replacement: $900-$1,700
- Single swing gate: $2,400-$5,500
- Sliding gate: $3,800-$7,500
- Double swing gate: $4,500-$8,200
What moves the number? Gate length and weight, whether posts can be reused or need new footings, the operator brand and horsepower, and whether we’re adding safety edges and photocells to meet current standards. We offer free estimates, no trip charge inside Brentwood, $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 and we’ll measure it and put the number in writing.
We Also Serve Cities Near Brentwood
Our Gate Installation crew covers the Brentwood area daily, including Oakley, Discovery Bay, Antioch, and Clayton. If you’re just outside 94513, we’re still close enough to show up on time and stand behind the work. And if you’re in the city itself, this page is for you: Gate Installation in Brentwood is what Hal and his crew do every week.
Serving Brentwood, CA - Our Local Coverage Area
We’re based in the Brentwood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Brentwood
Those operators were mostly installed during the 2000s building boom, and they have a service life of roughly 15 to 20 years, which means whole blocks are now hitting end-of-life within a few years of each other. If your neighbors off Sand Creek Road and Balfour Road are all replacing operators this year, yours is probably on borrowed time. Call (877) 610-2993 and we’ll inspect yours before it leaves you stuck outside.
The persistent afternoon wind puts constant lateral load on gate leaves, which accelerates hinge wear and makes operators work harder than their rated duty cycle. In Brentwood, you want a slide gate on a cantilever track or a swing gate with heavy-gauge hinges, wind-rated posts, and an operator sized above the bare minimum for your gate’s weight. We spec all of that as standard here, because the wind never takes a day off.
Most Brentwood HOAs have architectural guidelines that require written approval before any new gate or operator is installed, and the city of Brentwood may require a permit for work involving new concrete footings or electrical runs. We’ll tell you what applies to your specific address, and we’ll work from your HOA’s approved specs so the gate matches the neighborhood standard. It’s easier to do it right the first time than to answer letters later.
Steel expands when the temperature climbs, and Brentwood’s 100°F+ days cause gate frames to grow enough to bind against posts, ground hardware, and latch strikes. The fix is adjusting the clearances to account for the thermal range out here, and if the gate was installed with factory-tight specs, it was never set up for Brentwood summers. We re-hang it with proper clearances and the binding stops.
For Brentwood’s heat, wind, and soil moisture, a slide gate with a Viking or LiftMaster cantilever operator and moisture-rated loop wire is the most durable setup we install. Swing gates need an articulating arm or hydraulic operator rated for high-duty cycles and thermal protection. We’ll match the operator to your gate’s weight, wind exposure, and usage pattern, and the 90-Day Done Right Promise covers the work in writing. Call (877) 610-2993 for an exact quote, free.
Contact Gatewood Fence & Gate for Gate Installation in Brentwood
If you need a gate installed, replaced, or just looked at by someone who has been doing this since 2001, call (877) 610-2993. A live person answers, 24 hours a day, seven days a week, not a voicemail and not a call center three states away. Hal Gatewood’s name is on the shop and on every invoice, and if the work isn’t done right, one call brings him back. That’s the deal here, and it’s not going to change.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate.