Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in North Castle, NY
When a driveway gate stops working in North Castle, the call usually comes from a long private drive off Route 22 or Route 128, somewhere between Armonk and Banksville. We answer with a live person, and we know what we’re walking into before we get there: stone pillars that have shifted with the frost, operators that gave up after too many Westchester winters, and a homeowner who wants the gate fixed rather than replaced. Call (877) 610-2993 and you’ll get Hal or someone from his crew, not a recording.
Why North Castle Homes Are Different
North Castle sits in the inland Westchester hills, and that geography shows up in every gate we repair. Hard freeze-thaw cycles each winter heave the heavy stone and poured-concrete gate pillars, sometimes by an inch or more. A swing gate that closed perfectly in October can bind against its latch post by February. Frost movement also cracks the underground conduit that feeds operators, which means a gate that seems dead may actually just have a shredded wire run. Spring is our busiest season here, when homeowners finally get outside and discover what the ground movement did over January and February.
Then there are the trees. Many Armonk estate gates sit at the end of gravel drives bordered by mature oaks and maples. Over the years, those roots migrate under gate post footings, lift them, and throw the operator arm out of alignment. We reset the footing without tearing through the root network, because we know the landscaper is watching. The housing stock tells the same story: large-lot Colonial and Tudor estate homes, many built during the 1980s through early 2000s executive-housing boom, each with an automated entry gate that is now reaching the end of its service life.
Gate Repair in North Castle
Gate repair in North Castle usually means one of three things: a swing gate that no longer lines up with its latch, an opener that hums but won’t budge, or a welded joint that finally let go after thirty winters. We handle all three, and we do it in your driveway, not in some shop across the county. Our crew knows the estate roads and long private drives of Armonk, Banksville, and the Route 22 corridor well enough that we usually know the gate before we see it. Most repairs land between $180 and $520, and you’ll see the price in writing before we turn a wrench. For a deeper look at how we approach this work, see our Gate Repair service page.
Electric Gate Repair
Electric gate repair in North Castle commonly involves underground conduit that has cracked during a freeze-thaw cycle, letting moisture reach the low-voltage wiring that powers the operator. We trace the circuit, repair the conduit, and re-seal the connections properly rather than just wrapping things in electrical tape and hoping. We service and repair gate motors and control boards on site whenever possible. A full control board replacement typically runs $340 to $700, depending on the board, and we’ll tell you before we order anything.
Automatic Gate Repair
Automatic gates on North Castle estate properties tend to be heavy: ornamental iron, custom wood, or steel-frame gates mounted on stone pillars installed during the 1980s through 2000s. When the operator fails, we diagnose whether it’s the motor, the limits, the safety loops, or the arm itself. You’ll get an exact price before we start, and it won’t change at the door. A full operator replacement on a stone-pillar estate gate typically runs $900 to $2,400 installed.
Hinge and Post Repair
Here’s what we’ve learned doing hinge and post work in Armonk over the years: a sagging gate almost never bends in the middle. It sags at the hinge post, because the post has shifted, the anchor bolts have loosened, or the weld at the hinge has fatigued. We repair the post the right way, re-set the anchors, and re-weld on site so your gate stays in your driveway while we work. Fix the panel without the post and you’ll fix it twice. Hinge replacements and realignment work in North Castle usually land in the $220 to $380 range.
Gate Realignment
Gate realignment is our busiest repair once the ground thaws in March and April. Frost heave has a habit of moving heavy stone and poured-concrete gate pillars by an inch or more over a single winter, which is all it takes to throw a swing gate out of plumb. We re-level the gate leaf, adjust the hinge geometry, and re-tune the operator so the gate doesn’t bind or slam through its travel. Weld repairs on fatigued ornamental iron start around $150 per joint, and most jobs need two to four joints.
How fast can you get to a gate repair in North Castle?
In most cases, same-day service. We keep a local crew in the North Castle area, so a swing-gate failure or stuck opener usually gets a truck the same afternoon you call. Emergency calls come straight to Hal’s phone, not a voicemail system. Call (877) 610-2993 and tell us what the gate is doing.
Can you repair my gate if the pillar itself has shifted?
Yes, and this is exactly the kind of repair we do more than any gate company in the region. Frost-heaved pillars get re-set, re-anchored, and re-plumbed. We re-align the gate to match, and we fix the root cause rather than just bending the hinge to compensate. The 90-Day Done Right Promise applies to this work in full.
Gate Installation in North Castle
If you live in North Castle, chances are your driveway gate was put in when the house was built, sometime between the 1980s and the early 2000s. That gate has now lived through twenty to forty Westchester winters, and it’s showing it. A gate installation in North Castle usually means one of three things: the old gate is beyond repair and needs replacing, the pillars have shifted so badly the gate can’t be rehung without resetting them, or you’re putting in a gate where there wasn’t one. We build for the freeze-thaw cycle from day one, setting posts deeper than a standard install would call for. See our full Gate Installation service page for details.
Driveway Gate Installation
This is the bulk of what we do in North Castle. Long private drives off Route 22 and the surrounding roads, often bordered by stone walls or old-growth maples, need a gate that clears the grade and swings or slides without binding when the ground moves. A single driveway swing gate, including new posts or pillar reinforcement, usually falls between $3,800 and $7,500 in this market.
Double Swing Gate Installation
The classic Armonk estate look is a double swing gate mounted on stone or brick pillars. The pillar is the weak point. If it’s cracked or leaning, the gate will never close right. We reset pillars, re-anchor hinge bolts, and rebuild the masonry around the operator mount as part of a proper installation. A double driveway gate runs $7,000 to $14,000 installed, including the gate panels, posts, hinge hardware, and operator.
Pedestrian Gate Installation
Estate properties often have a separate walk gate beside the driveway, and it takes more abuse than people expect. It’s opened and closed by hand dozens of times a week, often by kids or landscapers. We match the walk gate to the driveway gate, whether that’s ornamental iron, wood, or a custom steel frame. A straightforward pedestrian gate installation in North Castle typically runs $900 to $2,200, depending on width and material.
Sliding Gate Installation
Sliding gates are popular here for one reason: they don’t need swing clearance. When the drive is steep or the pillars are close to a stone wall, a slide gate is the answer. But a slide gate only works as well as its track and the ground under it. We build the base to drain and resist frost heave before the track ever goes down. Sliding gates land in the $6,500 to $12,000 range when properly based and tracked in North Castle.
How fast can you get to North Castle for a gate that won’t close?
For a gate that’s stuck open, off its track, or won’t close in North Castle, we typically get a crew there same day, with next-morning the latest in most of the 10504 zip. A gate that won’t close is a security and liability problem, and we treat it that way. Call (877) 610-2993 for a real arrival window.
Is gate installation more expensive in North Castle than nearby towns?
Not really. The materials cost the same whether we’re installing in Armonk or Hartsdale. What changes is the labor. North Castle estate drives are longer, the pillars are often heavier stone or brick, and the ground conditions demand deeper, more careful footing work around roots and ledge. You’re paying for the site conditions, not a town premium.
Gate Motor & Opener in North Castle
A gate opener that quits in North Castle isn’t something you can put off until Friday. That gate is the only thing standing between your driveway and Route 22, and when it won’t open, you’re either stuck outside or locked in. We know the estate gates in Armonk, Banksville, and the winding drives off Bedford Road because we’ve worked on them for years. Most opener problems are repairable rather than replacement jobs, and we’ll tell you honestly which one you’re dealing with. Learn more on our Gate Motor & Opener service page.
Motor Installation
Installing a new gate opener on a North Castle estate isn’t a two-hour job. These are heavy gates on stone pillars, often at the end of a long gravel drive. We benchmark everything on site: gate weight, swing arc, hinge condition, conduit routing, and the pillar base itself. A motor installed on a pillar that has already shifted from frost is a motor that will fail early. Replacing a swing-arm motor on an estate gate usually falls between $900 and $2,200 with motor, mounting hardware, and labor included.
Motor Repair
We repair first. That’s the whole point. A lot of companies see a dead operator and quote a full replacement. Hal looks at the capacitor, the control board, the limit switches, and the gear assembly. Often the problem is a $40 part and a misaligned photo eye. A typical motor repair in North Castle runs $165 to $380, and we’ve rebuilt more old LiftMaster and Elite units than we’ve replaced.
Linear Arm Motors
Linear arm motors are popular on the swing gates common to North Castle’s Colonial and Tudor estate homes. They fail in specific ways: the arm seizes, the internal limit cams drift, or the capacitor overheats after years of holding against wind load. We stock Linear replacement arms and boards for the most common models so we can usually fix the unit same day rather than waiting on a distributor. If the arm has been binding because the pillar shifted, we address the pillar too.
Slide Gate Motors
Slide gates on North Castle properties tend to be longer and heavier than what you’d see in a standard Westchester suburb. That means the motor and gear rack take real abuse every cycle. Common failures here include stripped drive gears, broken chain or belt drives, and frame-bound rollers from frost-heaved track sections. Slide gate motor replacements run $1,400 to $3,200 because of the chain or belt drive and the gear rack work involved.
Can you fix a gate motor same day in North Castle?
In most cases, yes. If the failure is a bad capacitor, misaligned limit switch, failed photo eye, or blown control board, and your gate is one of the brands we stock parts for, the repair is usually done in one visit. A full operator replacement where a motor needs to be ordered for an unusual model might take a few days. Call (877) 610-2993 and we’ll tell you what we’re dealing with.
Do gate opener repairs cost more in North Castle than in White Plains or Greenburgh?
Our prices don’t change based on the town. What does affect cost in North Castle is the gate itself: estate gates on stone pillars with long underground conduit runs take more labor than a suburban gate on a steel frame. But the hourly rate and parts pricing are the same whether you’re in Armonk or Hartsdale.
Gate Access Control in North Castle
A gate access system that won’t open on a cold Armonk morning is a security headache, not just an inconvenience. For North Castle homeowners, the typical fix runs $250 to $800 depending on whether we’re replacing a keypad, a receiver board, or the entire operator. We work on systems that were installed during the 1990s executive-housing boom, and we can usually get them talking to a modern remote or phone app without ripping everything out. See our Gate Access Control service page for the full scope.
Keypad Entry Systems
A keypad on a North Castle stone pillar takes a beating from freeze-thaw cycles and road salt spray, especially along Route 128 and Middle Patent Road where plows throw brine all winter. We replace failed keypads, re-seal weather-tight housings, and wire in modern units that drop into older housings without butchering the stonework. A keypad replacement typically runs $250 to $450 installed, depending on whether we can reuse the existing housing.
Remote Control Upgrades
Most North Castle gates still run on single-button clickers and older Linear or Elite transmitters that are easy to clone. We upgrade systems to rolling-code remotes, configure multi-vehicle programming, and add wireless keypad backups so you’re not locked out when the remote battery dies in the supermarket lot in downtown Armonk. Remote control programming and replacement runs $40 to $120 per remote.
Phone Entry and Intercom Integration
Estate gates on Banksville Road and Wampus Lake frontage often sit far enough from the house that you can’t hear the gate bell. Phone entry systems route the gate call to your cell, letting you open the gate from anywhere. We run the conduit, mount the call box, and tie it into existing access control wiring for DoorKing and Viking systems that may have been installed years ago. Phone entry and video intercom installations usually run $1,400 to $3,200 because they involve pulling new wire under driveways and tying into the house network.
Card Reader and Smart Access Systems
Some newer North Castle properties are switching to card readers or smartphone-based access so they can log who comes and goes. We install card reader panels, program credentials, and set up app-controlled openers that work with the brands already mounted on the pillar. Hal’s been at this long enough to tell you honestly whether a new smart controller will talk to your older Elite receiver or if you’re better off replacing the receiver board now rather than chasing gremlins later.
Why did my gate keypad stop working after winter in North Castle?
Frost heave almost always plays a part. The repeated hard freezes in the inland Westchester hills move stone pillars by an inch or more each winter, and that movement stretches or snaps the low-voltage access wiring where it exits the pillar. Sun-cracked membrane keypads are also common on south and west-facing pillars. We bury service loops and sleeve everything through conduit to prevent a repeat.
Can you add phone entry to my existing gate in North Castle?
Yes, and it’s a common upgrade on estate lots where the gate sits too far from the house to hear a bell. We mount the call box at the gate, run conduit back to the house, and tie it into your existing opener. If the underground wire is shot, we pull a clean new run without tearing up the lawn. Call (877) 610-2993 for a line-item quote.
Gate Parts & Welding in North Castle
Gate parts and welding in North Castle typically runs $220 to $540 for hinge replacement, $380 to $900 for post reset or replacement, and $180 to $480 for custom weld repairs on ornamental iron. Most calls we handle same week, and a live person answers at (877) 610-2993 any hour you call. If you’re on a wooded lot off Cox Avenue with a heavy gate that’s started dragging, we’ll send someone who knows exactly what frost heave and tree roots do to a post footing. More detail is on our Gate Parts & Welding service page.
Hinge Replacement
Heavy ornamental gates on North Castle estate properties hang on barrel hinges, strap hinges, and pillow block bearings that wear out faster than most people expect. We see torn lower barrel hinges on swing gates that have carried an extra hundred pounds of snow load each winter. Hinge replacement here means matching the gauge and throw of the original, not slapping on a lighter-duty part and calling it done. Hinge replacement on a heavy ornamental gate runs $220 to $450 per hinge, depending on the barrel size.
Post Replacement
The frost heave around Armonk moves stone and concrete pillars an inch or more in a bad winter. That throws the gate out of plumb, breaks the hinge welds, and binds the latch. Post replacement in North Castle almost always involves re-bedding the footing below frost depth and re-anchoring the operator arm. Post reset or replacement runs $380 to $900, with the higher end covering pillar work where we lift the gate, re-bed the footing, and re-anchor the operator.
Rail Repair
Slide gates on North Castle driveways take a beating from dirt, salt, and leaves that pile up along the rail. The rail itself bends or corrodes, and the gate starts grinding instead of gliding. We straighten or replace the rail, adjust the guide rollers, and make sure the rack and pinion mesh is clean. Slide gate rail work sits in the $300 to $700 range in this market.
Custom Welding
Some of the gates around North Castle were built as one-offs by iron shops that are long gone. To weld a cracked scroll or a snapped picket on those gates, you have to match the original metal thickness and finish, then repaint without leaving a scar. We weld on site, with the gate still hanging, whenever that’s the right call. Custom welding costs $120 to $300 per hour including materials for most repairs on North Castle estate gates.
Why does my Armonk estate swing gate sag every spring after the ground thaws?
Because the stone or concrete pillar has heaved over the winter, and the hinge post moved with it. When the ground freezes and thaws repeatedly on North Castle’s inland hills, water in the footing lifts the pillar just enough to throw the gate out of plumb. The proper fix starts at the footing, not the hinge.
Can you weld a cracked ornamental iron gate without removing the stone pillar?
Usually, yes. We weld on site, and for most cracks in scrollwork, pickets, or hinge plates, we can work with the gate still in place or lifted slightly off its hinges. If the pillar itself has to be reset, we may need to lift the gate off its hinges and support it with jacks while we re-bed the post. A cracked hinge plate on a gate that’s still load-bearing is a safety issue, so call us before it fails completely.
Brands We Service in North Castle
We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, and DoorKing systems every week in North Castle, plus Elite and Mighty Mule. We keep common repair parts in the truck, and for older boards we can usually source them faster than a distributor will ship to a homeowner. Full details are on our brands page.
Pricing for Gate Repair in North Castle, NY
| Service | Typical range in North Castle |
|---|---|
| Gate repair (general) | $180 - $520 |
| Hinge replacement or realignment | $220 - $380 |
| Weld repair (per joint) | $150+ |
| Control board replacement | $340 - $700 |
| Operator replacement (stone-pillar estate gate) | $900 - $2,400 |
| Pedestrian gate installation | $900 - $2,200 |
| Single driveway swing gate installation | $3,800 - $7,500 |
| Double driveway gate installation | $7,000 - $14,000 |
| Sliding gate installation | $6,500 - $12,000 |
| Gate motor repair | $165 - $380 |
| Slide gate motor replacement | $1,400 - $3,200 |
| Keypad replacement | $250 - $450 |
What pushes a North Castle price toward the top of these ranges is almost always the site: a sloped driveway, a frost-shifted pillar that needs re-bedding, tree roots under the footing, or an underground conduit run that has to be pulled new. The price is quoted and agreed in writing before any work starts, and that number is the number on the invoice.
Neighborhoods We Serve in North Castle
We work throughout North Castle, from the estate drives of Armonk to the quieter lanes of Banksville and Windmill Farm. Typical response time in the area is same-day for emergency repairs, next-day for scheduled work.
- Armonk
- Banksville
- Windmill Farm
- North White Plains (town line)
Service Area - Cities Near North Castle
Gatewood Fence & Gate serves North Castle, NY and the surrounding Westchester communities. We regularly work in White Plains, NY, Pound Ridge, NY, Hartsdale, NY, Greenburgh, NY, and Irvington, NY. If you’re on the edge of town, call us at (877) 610-2993 and we’ll tell you straight whether we can get there same day.
Serving North Castle, NY - Our Local Coverage Area
Gatewood Fence & Gate crews serve North Castle and the communities around it; dispatch is coordinated from our New York City office. The map shows the North Castle coverage area; if your address is on it, we can help.
Also serving nearby: North Castle, NY, White Plains, NY, Pound Ridge, NY, Hartsdale, NY, Greenburgh, NY, Irvington, NY.
FAQs About Gate Repair in North Castle
Yes. We cover the entire 10504 zip code and the surrounding neighborhoods: Armonk, Banksville, North White Plains, and the Route 22 and Route 128 corridors. No trip charge inside the county, and we don’t treat Armonk as a “far away” premium zone. Call (877) 610-2993 and we’ll give you a real arrival window.
Most repair work on an existing gate doesn’t trigger a permit, but new installations and major pillar reconstruction can. North Castle building codes care about setback lines, electrical work, and anything that changes the driveway approach. We’ll tell you what’s needed for your specific job before we start, and the quote covers any work we do after the permit is in hand.
Every repair and installation we perform carries a written 90-Day Done Right Promise. If the fix doesn’t hold, we come back and make it right at no charge. The guarantee is stamped on your invoice, not hidden in fine print. If a repair fails because of a new problem, we’ll show you the difference and quote a fair price before touching anything.
If your gate is acting up in North Castle, call (877) 610-2993. A live person answers, the estimate is free, and the price you’re quoted is the price you’ll pay.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What North Castle Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg