Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Everett
Gate repair in Everett usually means one of three things: a hinge post that’s rusted through at the base, an operator board that quit after a nor’easter, or a sagging panel that drags on the pavement. We fix all three, most jobs the same day. You’ll pay $185 to $340 for a typical hinge or realignment repair in 02149, and the price is set in writing before any work starts. Call (877) 610-2993 and a live person answers, day or night. Not a voicemail, not a call center in another state. Someone who knows Everett’s gates.
Key Takeaways
- Most hinge, post, and realignment repairs in Everett run $185 to $340, quoted upfront before work begins.
- Salt air off the Mystic River and Chelsea Creek rusts iron gate hardware in under a decade, not the 20 years you’d see inland in Malden or Medford.
- We weld on site and repair before we ever suggest replacing. The gate stays in your driveway.
- Every job carries a written 90-Day Done Right Promise. If it’s not right, Hal makes it right.
- Live person answers the phone 24/7. No voicemail maze.
Why Gatewood Fence & Gate Is Everett’s Preferred Gate Repair Company
Hal Gatewood started this shop in 2001 and his name is still on the door. That matters in a city like Everett, where half the gates we touch are older than the people who own them. We’ve rebuilt hinge posts in the tight side alleys off Broadway, rehung shared wrought-iron gates between triple-deckers, and pulled countless rusted-solid latch plates off century-old fences near the river. We know which blocks get the worst salt exposure and which post footings the freeze-thaw heaves out of plumb first.
What customers in 02149 tell us they want is simple: a company that shows up, calls back, and fixes the gate without inventing reasons to replace it. That’s the whole model. Hal or one of his crew handles the job. The person who shakes your hand is the person who’s accountable for the work. No subcontracted strangers, no faceless “technician team” that changes every visit. And if it’s not done right, you make one call and Hal comes back. That’s the 90-Day Done Right Promise, and it’s stamped on every invoice, not buried in fine print.
We also answer the phone. At 9pm when an Everett Gate Motor & Opener starts grinding because a salt-corroded board finally gave up, you get a person, not a recording. Some of our Everett customers have had the same cell number for Hal for ten years. That’s the accountability a national outfit can’t fake.
Our Gate Repair Services in Everett
Hinge & Post Repair
This is the bread-and-butter of Gate Repair in Everett. An iron gate that sags is almost never a case of a bent panel. The failure is in the hinge post, which has usually corroded at the base plate after years of salt-laden air off Chelsea Creek and the Mystic River. We cut out the old post, set a new galvanized one in a deeper footing, and rehang the gate with stainless fasteners that won’t rust through in five years. On a 1920s triple-decker side gate with 18 inches of swing clearance, that post has to be dead plumb or the gate binds on the house on every swing.
Gate Realignment
Freeze-thaw cycles in Everett are relentless. Water gets into the footing, freezes, expands, and shoves the post out of alignment. The panel looks crooked, but it usually isn’t. We realign gates in place by correcting the post geometry and hinge spacing, not by bending the frame. In dense neighborhoods around Broadway and Ferry Street where shared fence-line gates run between two separately owned triple-deckers, we also get the “neighbor question” sorted before we touch a single bolt. Two owners, one gate, one invoice. It happens more often here than anywhere else we work.
Weld & Rust Repair
Salt air is unforgiving to painted steel. Wrought-iron gates near the water in Everett often show structural rust at the bottom rail within eight to ten years, and the hinge plate follows close behind. Our Everett Gate Parts & Welding crew works on site, in your driveway or side yard, so the gate never leaves your property. For a rusted-through bottom rail, we cut out the compromised section and weld in a fresh piece, then prep and paint to match. Galvanized steel and stainless hardware are the standard here, not an upsell. It’s what actually survives next to a tidal waterway.
Electric Gate Repair
Automatic gate operators in Everett fail differently than inland units. The control boards take a beating from humid, salt-heavy air and from the voltage dips that come with old triple-decker wiring. We service Linear, Viking, Ghost Controls, and DoorKing operators, among others, and we keep common boards and limit switches stocked for same-week repairs in 02149. We’d rather replace a corroded limit switch than an entire operator. Saves you hundreds, and the gate keeps working.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everett
We’re certified to service nine major gate brands, and in Everett we see a lot of Linear, Viking, and Ghost Controls operators on residential driveways and side alleys. Brand matters less than how the hardware holds up to salt air, so we stock the replacement boards, remotes, and limit switches that actually fail here rather than making you wait a week for a part to ship. If your operator is older and parts are discontinued, Hal can usually match it with a compatible alternative. If not, he’ll tell you straight, and you’ll know the cost before he makes a move.
Common Gate Repair Problems We See in Everett Homes
- Salt-air hinge seizure. On pre-1930 iron gates near the Mystic River and Chelsea Creek, hinge pins and latch plates rust solid in six to eight years. That’s a cut-off-and-replace job, not a lubrication job. We see it weekly on the narrow lots off Broadway.
- Heaved post footings. Everett’s freeze-thaw cycle works concrete loose and pushes shallow footings out of plumb. The gate panel stays straight but hangs low on the latch side. We core out the old footing and pour a deeper one that actually survives.
- Shared-gate disputes. Dense triple-decker blocks often have one gate straddling two properties. Neither owner wants to pay first, so small rust blooms become structural hinge post failures. We document the condition, quote the repair, and split the invoice however the neighbors agree.
- Operator board corrosion. Automatic gates near the water develop a thin film of salt inside the control box over time. Boards stop reading remotes, or the gate opens and won’t close. We pull the board, clean the contacts, and replace it only if it’s truly dead.
Pricing for Gate Repair in Everett, MA
You won’t get a vague “call for pricing” from us. Here’s what gate repair in Everett actually costs, based on the jobs we’ve done in 02149.
- Hinge pin or latch plate replacement: $145 to $260, depending on access and how much cutting is involved.
- Post replacement with new galvanized post and footing: $320 to $580. Tight side yards bump the labor slightly, but our price is set before we start.
- Gate realignment: $180 to $340. Includes adjusting hinge geometry and shimming the panel.
- Weld repair on a rusted bottom rail or hinge plate: $90 to $210 per welded section, done on site.
- Operator board or limit switch replacement: $140 to $360, part included, depending on brand.
Those ranges cover the work, not just the visit. You get the number in writing before any torch lights or wrench turns. If you have a written estimate from another Everett company, bring it and Hal will give you a free second opinion. And take $40 off any repair over $200, plus a standing 10% discount for seniors and veterans. No haggling. Just the price he’d quote his own mother.
We Also Serve Cities Near Everett
Our service area for Gate Repair in Everett extends into the surrounding streets of Malden, Chelsea, Revere, and Medford. Same crew, same truck, same 90-day promise. If you’re a few minutes over the line, call and ask. We’re usually closer than you think.
Serving Everett, MA - Our Local Coverage Area
We’re based in the Everett area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Everett
Because Everett sits between the Mystic River and Chelsea Creek, and that’s two bodies of tidal salt water pumping salt-laden air into tight side yards all year. A painted steel hinge on a 1920s iron gate in Everett can seize solid in six to eight years, while the same hinge inland in Malden or Medford might last 15 to 20. The difference is constant marine moisture and salt film on the metal. That’s why we default to galvanized steel and stainless fasteners on every Everett repair. Call (877) 610-2993 and we’ll tell you whether your hinge needs cutting out or just a good cleaning.
Whoever owns the fence line under Massachusetts law, or whoever agrees in writing to have the work done. In practice, on shared gates in Everett, we document the failure, write one estimate, and you and the neighbor decide how to split it. We’ve repaired dozens of shared side gates off Broadway and Ferry Street where both owners went easy on each other and split it down the middle. The gate gets fixed. Nobody gets a surprise invoice. Call (877) 610-2993 and we’ll write the estimate with both names on it if you want.
The post, almost every time. The bottom hinge plate and the post base plate sit closest to ground moisture and salt spray, and that’s where the corrosion eats through. The panel usually looks straight for years while the post rots from the inside at the base. Then the whole gate drops and drags. We replace the post before the panel goes, and the gate ends up better than it was. Call (877) 610-2993 and we’ll tell you what’s salvageable after one visit.
Yes. We handle Gate Access Control in Everett, including the blocks closest to Chelsea Creek where salt film inside the control box causes board failures earlier than the manufacturer’s rating. We pop the cover, inspect the board, clean the corrosion, and replace only what’s dead. Most operators we see are Linear or Viking units. Call (877) 610-2993 and we’ll come look at it, usually same day.
A properly installed galvanized steel post on a newer gate should hold for 20 to 30 years even with Everett’s salt air, provided the footing is deep enough and the hardware is stainless. The older painted steel posts from the 1920s don’t owe anyone an apology, but they’re typically done at the base after 10 to 15 years near the water. That’s a normal repair, not a defect. Call (877) 610-2993 for a free assessment of your post’s condition and a written price if it needs work.
Contact Gatewood Fence & Gate in Everett
If your gate sags, drags, won’t open, or has rust holes near the base, don’t wait for winter to make it worse. Call (877) 610-2993 for a free estimate. Hal or one of his crew will meet you, look at the gate, and give you a written price before any work starts. No trip charge inside the county. No surprise invoices. No runaround. Just a gate that works again.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Everett since 2001.