Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Commerce City, CO
Gate repair in Commerce City typically runs $180 to $340 for most service calls, and we can usually have someone at your property the same day you call. If you’re off E 104th Ave, down by the South Platte, or out in Reunion, you already know that gates here fail differently than they do in Denver or Aurora. The refinery corridor, the open wind, the older ranch stock in ZIP codes 80022 and 80037 - it all adds up. Call (877) 610-2993 and you’ll talk to someone who actually works on gates, not a script reader.
Why Commerce City Homes Are Different
Commerce City sits on the open high plains northeast of Denver, and there is no mountain or ridge to slow the wind down before it hits your gate. Strong downslope Front Range winds stress hinges, warp lightweight aluminum gate panels, and knock automatic opener arms out of alignment, which is why we see alignment and roller failures here far more often than in sheltered neighborhoods just a few miles west.
Winter’s freeze-thaw cycling works its way into the track and ground hardware, heaving posts and pinching rails. Combine that with the town’s industrial air along the Suncor Energy refinery corridor and the South Platte River, and you get a specific local problem: sulfur compounds and airborne particulates that accelerate corrosion on steel gate frames, hinges, and rollers. West- and south-facing gates closest to the refinery routinely show deep pitting and rust scale within two or three years of installation. In practice, that means Commerce City gate repair is not a generic job - it requires a technician who knows to spec hot-dip galvanized hardware or powder-coat touch-ups at every service call, not just when visible rust appears.
Gate Repair in Commerce City
Most gate repair calls in Commerce City fall into two categories: the older ranch homes south of E 88th Avenue with gates that have been sagging since the 1990s, and the newer ornamental iron driveway gates in Reunion and the 80022 corridor that have been knocked out of alignment by wind. We handle both, and we quote the price before any work starts. Gate Repair is what we’ve built this shop on - fixing what’s there rather than talking you into replacement.
Electric Gate Repair
Older homes in central Commerce City, especially the 1950s-to-1970s ranch neighborhoods south of E 88th Ave, often still run pre-2000 gate operators. Those control boards are obsolete now. They lack modern safety photocell inputs, and many were installed before UL 325 entrapment protection became the standard. We can retrofit most of them with current boards and new safety edges, and we’ll tell you honestly when the cheaper answer is a full operator swap. A retrofit typically runs $260 to $410 in Commerce City.
Hinge and Post Repair
A gate sags in the hinge post. Not in the middle. Anyone who fixes only the panel will be back to fix it again, and so will you. We weld on site, in your driveway, so the gate never leaves your property. In Commerce City, we spec hot-dip galvanized hardware or powder-coated replacements as standard practice because the sulfur compounds from the refinery corridor eat standard steel hardware in two to three years on west- and south-facing exposures. Hinge and post repair typically costs $220 to $450, including footing replacement when needed.
Weld and Rust Repair
This is the work we do more in Commerce City than almost anywhere else on the Front Range. Rust scale, pitting, and weld stress on gate frames and posts near the refinery corridor are not cosmetic. They’re structural. We weld new steel plate over compromised sections, reinforce hinge mounts, and treat rust before it becomes a collapse hazard. Weld and rust repair runs $200 to $480 for most gates. We’ll show you the repaired section before we finish, so you can see exactly what we did.
Why do gate hinges rust so fast in the older neighborhoods near the Suncor refinery?
Sulfur compounds and airborne particulates from the refinery corridor accelerate corrosion on steel gate frames and hinges. West- and south-facing gates in the older neighborhoods closest to the corridor can show deep pitting within two to three years, far faster than in Denver or Aurora. The answer is hot-dip galvanized hardware or powder-coated replacement parts, which we spec at every service call in Commerce City. Call (877) 610-2993 for an exact quote - estimates are free.
Can my 1970s-era gate operator be retrofitted for modern safety sensors?
Yes, many pre-2000 operators can be retrofitted with current safety photocells and new control boards, especially units from major brands like FAAC, BFT, or Linear. But some boards are obsolete and no longer supported, and in those cases a replacement operator is the more economical answer. We’ll tell you plainly which one applies to your gate. Call (877) 610-2993 for an exact assessment - the second opinion is free.
Gate Installation in Commerce City
A new gate installation in Commerce City typically runs $1,900 to $7,500 depending on the gate type, automation, and what’s already in the ground. Most driveway gate installs take two to three days from post setting to final opener programming. We know the houses, the soil, and the particular beating Commerce City air hands to steel, and we quote your price before any work starts. Gate Installation is measured, ordered, and scheduled - no same-day promises, just a free measure and a written price you can count on.
Driveway Gate Installation
A driveway gate in Commerce City has to survive downslope winds off the high plains and freeze-thaw cycles that heave post footings. We set posts below frost line, weld on site, and install operators from brands we trust. Whether you’re securing a construction yard off Highway 85 or a residential driveway in the 80022 corridor, the gate has to close square and stay square. A basic single swing gate without automation runs $1,900 to $3,200 installed.
Sliding Gate Installation
Sliding gates are common along the industrial edges of Commerce City, but we also install them for residential lots with tight driveway space. The key here is the rack and pinion, and older versions bind and skip teeth when ice loads the track in January. We replace the drive with a modern Linear or BFT setup, add a safety photocell, and make sure the track drains so freeze-thaw doesn’t wreck it every winter. A sliding gate with a new operator starts around $3,500 and goes to $5,800 depending on width and track condition.
Swing Gate Installation
Swing gates bear the worst of Commerce City’s wind stress. Downslope gusts push against a wide panel and the hinge post takes all of it. When we install a new double swing gate on an ornamental iron driveway, we use hot-dip galvanized hinge hardware and reinforce the post at the weld line. It costs a little more up front. It saves a callback in 18 months when a cheaper post shears. A full ornamental iron double swing gate with an opener is $5,500 to $7,500.
Can you retrofit an automatic swing gate built before UL 325 safety standards in Commerce City?
Yes, and this is one of the most common retrofit calls we handle in Commerce City’s older ranch neighborhoods. A pre-UL 325 gate needs entrapment protection added, a new control board with current safety logic, and usually a complete rewire of the operator. We can often save the gate panel and posts, but the electrical and safety hardware has to be replaced to meet current standards. Call (877) 610-2993 for a free measure and written quote.
How often should gate hinges and rollers be serviced near the Suncor refinery corridor?
Every 12 to 18 months, and that’s specific to Commerce City’s industrial air. Sulfur compounds and particulates accelerate corrosion on hinge barrels, roller bearings, and track hardware faster than in Denver or Aurora. A quick service call to lubricate, inspect for pitting, and touch up powder coat costs far less than replacing a seized roller assembly. Call (877) 610-2993 to schedule - we quote before any work starts.
Gate Motor & Opener in Commerce City
Gate motor and opener repair in Commerce City typically runs $285 to $640 for most motor replacements, with slide motor swaps landing around $450 to $900 depending on brand and gate weight. We respond to Commerce City calls the same day in most cases, and a live person answers the phone at (877) 610-2993 whenever you call, 24 hours a day. Gate Motor & Opener service is what gets your gate moving again when the motor hums but the gate doesn’t budge.
Motor Installation
New motor installation in Commerce City runs $600 to $1,400 for most residential swing and slide gates, including mounting, wiring, and safety sensor alignment. On new construction in Reunion and the surrounding 80022 corridor, we commonly add automation to gates that were installed manual by the builder. That means running proper conduit, setting limits, and wiring a loop detector so the gate stops when a car is on the pad, not when the arm already touched the bumper. You’ll get a written price before we start, and that price is what you pay.
Motor Repair
Repair calls in Commerce City split into two buckets. The first is electrical: burned contacts, corroded circuit boards, limit switches that have pitted from refinery particulates. The second is mechanical: worn rack and pinion teeth, seized rollers, hinge posts that have shifted just enough to bind the operator. We diagnose both on site. Hal welds on site too, so a cracked bracket or a stressed mounting plate gets fixed in your driveway, not hauled to a shop. Standard motor replacement runs $285 to $640.
Linear Motor
Linear swing arm motors are common on the ornamental iron gates you see in Reunion and the larger properties along Tower Road. A typical Linear motor replacement in Commerce City runs $400 to $850, depending on gate leaf weight and arm stroke. These units need clean limit alignment and a solid hinge post. Downslope winds off the high plains are unforgiving on linear arms. If the post flexes, the arm binds, and the motor burns out fast. We check the post before we swap the motor.
How often should a gate motor be serviced in Commerce City given the refinery air?
Every 12 to 18 months minimum, because the sulfur particulates from the Suncor and South Platte industrial corridor corrode limit switches, board contacts, and motor terminals faster than in neighboring cities. A spring and fall check keeps seals tight and catches pitted contacts before the board shorts. We include a corrosion inspection on every Commerce City service call. Call (877) 610-2993 to schedule.
Why did my builder-grade LiftMaster opener fail after only two years in Reunion?
The usual answer is a combination of an unsealed motor housing, sulfur corrosion on the terminals, and a hinge post that sagged just enough to bind the rack and pinion. Builder-grade openers are not spec’d for Commerce City’s air quality, and the motor burns out under load. We replace them with sealed units and galvanize the post while we’re there. Two years is fast, but we see it regularly. Call (877) 610-2993 for a free second opinion on any written estimate.
Gate Access Control in Commerce City
Gate access control in Commerce City usually means one of two things: a keypad or remote that has stopped talking to the opener, or a full system that never worked right from the day it was installed. We fix both. A typical keypad replacement in Commerce City runs $185 to $340 installed, and a phone-entry or card-reader setup for a driveway gate usually lands between $900 and $2,400 depending on the hardware and how far the power run has to go. Gate Access Control is about making your gate respond when you need it to, whether that’s a clicker in your truck or a fob for the whole HOA.
Keypad Entry
Most Commerce City keypads die two ways: the membrane face cracks and lets moisture into the board during freeze-thaw cycles, or the internal contacts corrode from airborne sulfur compounds. We replace the whole keypad, not just the face, because patching a cracked keypad on a north-facing gate off East 64th Avenue in February buys you maybe one season before it fails again. A new wired keypad installed in Commerce City typically runs $185 to $340.
Phone Entry
Phone entry systems for Commerce City gates let you open the gate from your cell phone, which matters on long driveways in ZIP 80022 where you can’t hear the gate runner from the house. A cellular-based phone entry setup typically runs $900 to $1,800 installed, depending on whether we’re tying into an existing opener or replacing the whole control board. These systems are a good fit for acreage properties north of 104th Avenue where running new low-voltage wire back to the house is more expensive than the cell module itself.
Card Reader and Video Intercom
HOA communities like Reunion and the master-planned neighborhoods in the northern 80022 corridor increasingly want card-reader and video-intercom access on their community gates. We install and service those systems, including the wireless fob readers that let residents open the gate without rolling down a window in January. A card reader or video intercom for a residential gate runs $1,200 to $2,400. Video intercom works well on Commerce City properties where the gate is far from the house and you want to see who’s at the driveway before you open anything.
Can you install a solar gate opener for my long driveway in the northern 80022 corridor?
Yes, and we do it regularly on the acreage and large-lot properties north of 104th Avenue where running grid power to the gate costs more than the opener itself. A solar gate opener package starts around $1,400 installed, and we set the panel tilt for Commerce City’s winter sun angle so the battery bank doesn’t die in January. If your driveway is long enough that the gate is out of earshot, we can add a phone entry system too. Call (877) 610-2993 for a free estimate.
Do you install card reader or video intercom access for HOA communities like Reunion?
Yes. We install and service card-reader, fob, and video-intercom access for HOA-managed community gates in the master-planned neighborhoods of the northern 80022 corridor, including Reunion and the surrounding subdivisions. Those systems need a different skill set than a single-family driveway gate because you’re managing dozens or hundreds of credentials and a board that has to sync with the HOA’s management. We’ll quote it, install it, and stand behind it with the 90-Day Done Right Promise. Call (877) 610-2993 and we’ll walk through what your gate needs.
Gate Parts & Welding in Commerce City
Gate parts and welding in Commerce City usually means one of three situations: a hinge post rusted through at ground level, a slide gate dragging its rollers off a heaving track, or a weld crack where the high-plains wind has been flexing a panel for three winters. Repair work here runs $180 to $650 for most hinge, post, and rail fixes, and we quote the full price before we touch anything. Gate Parts & Welding is where we fix the metal itself, not just bolt on a replacement part.
Hinge Replacement
Hinge replacement in Commerce City is rarely just about the hinge. The airborne sulfur compounds from the Suncor corridor strip standard zinc plating from hinge hardware within a few seasons. By the time a gate starts sagging, the hinge plate is usually pitted and the lag bolts have lost their bite in the post. We cut off the old hardware, weld on new hinges sized for the gate’s weight, and use galvanized fasteners that hold up longer against this city’s air. Hinge replacement on a residential gate typically costs $180 to $340 including hardware and labor.
Post Replacement
Gate posts fail at ground level in Commerce City, not at the top. Frost heave works the concrete footing loose, then airborne moisture and industrial particulates eat the steel right where it meets the concrete. We dig out the old footing, set a new 3-inch galvanized post in concrete at a depth that survives freeze-thaw cycling, and weld your gate hardware back in place. A full post replacement, including excavation, a new galvanized post, concrete, and re-hanging the gate, runs $350 to $650 depending on post size and access.
Custom Welding
Not every Commerce City gate needs a mechanical repair. Sometimes a panel has cracked at the weld points, or a homeowner wants a custom gate built for an odd-sized opening between a house and a shared fence line. We do custom MIG and stick welding on site. If your ornamental iron driveway gate in Reunion has a crack, we’ll weld it, grind it smooth, and match the finish as closely as the original coating allows. Most small crack repairs and bracket re-welds come in between $150 and $300.
Why do my gate hinges and rollers rust so much faster in Commerce City than my relatives’ gates in Aurora?
Commerce City’s industrial corridor along the South Platte River releases sulfur compounds and airborne particulates that accelerate corrosion on steel gate hardware. Hinges and rollers here routinely show deep pitting and rust scale within two to three years of installation, while the same hardware in Aurora or Denver might last five to seven years. We recommend hot-dip galvanized hardware and powder-coat touch-ups on every service call in Commerce City, not just when the rust is already visible. Call (877) 610-2993 for a free estimate.
Can you weld a crack in my ornamental iron gate in Reunion without ruining the powder-coat finish?
We can weld the crack and restore the structural integrity of the gate, and we’ll grind the repair smooth and match the finish as closely as the original coating allows. Any weld will require touching up the finish at the repair site, but we minimize damage by grinding a narrow V and using controlled short arc passes. Hal’s crew has done this work on ornamental iron gates throughout Reunion and the 80022 corridor. Call (877) 610-2993 for an exact quote.
Brands We Service in Commerce City
We stock parts and carry factory authorization for nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Commerce City, we keep FAAC and BFT operator boards, Linear limit switches, and Viking arm assemblies on the shelf because those are the brands we see most often in this market. Most parts orders arrive next day if we don’t have them in stock. our brands
Pricing for Gate Repair in Commerce City, CO
| Service | Typical range in Commerce City |
|---|---|
| Basic gate repair service call | $180 - $340 |
| Gate realignment | $160 - $280 |
| Hinge and post repair | $220 - $450 |
| Weld and rust repair | $200 - $480 |
| Electric gate operator repair | $190 - $380 |
| Lock repair | $80 - $160 |
| Gate motor replacement | $285 - $640 |
| Slide motor replacement | $450 - $900 |
| Linear arm motor replacement | $400 - $850 |
| New motor installation with safety sensors | $600 - $1,400 |
| Keypad replacement | $185 - $340 |
| Phone entry system | $900 - $1,800 |
What pushes price up in Commerce City is post condition, corrosion damage from refinery air, and whether the existing concrete footing has to be cut out and re-poured. The price we quote before any work starts is the price on the invoice - not a penny more unless you approve a written change in scope while we’re on site.
Neighborhoods We Serve in Commerce City
We run gate repair and installation calls across both Commerce City ZIP codes, from the master-planned streets of Reunion up in 80022 to the older ranch-home blocks near Derryberry Park and the neighborhoods along the South Platte industrial spine. Same-day response is available depending on where you are and what broke - call (877) 610-2993 and we’ll tell you honestly when we can be there.
- Reunion
- Belle Creek
- Buffalo Run
- Old Commerce City / 80037 corridor
- Near Derryberry Park
Service Area - Cities Near Commerce City
We coordinate dispatch and scheduling from our Denver office, and crews serve Commerce City locally every day. If you’re just outside city limits, we also work in Derby, CO, Welby, CO, Sherrelwood, CO, Federal Heights, CO, and Thornton, CO. Every job carries the same 90-Day Done Right Promise and upfront pricing, no matter which side of the line you’re on.
Serving Commerce City, CO - Our Local Coverage Area
Gatewood Fence & Gate crews serve Commerce City and the communities around it; dispatch is coordinated from our Denver office. The map shows the Commerce City coverage area; if your address is on it, we can help.
Also serving nearby: Commerce City, CO, Derby, CO, Welby, CO, Sherrelwood, CO, Federal Heights, CO, Thornton, CO.
FAQs About Gate Repair in Commerce City
Most repair calls in Commerce City are scheduled same day, and a live person answers the phone 24/7 at (877) 610-2993. Response time depends on your location within ZIP 80022 or 80037 and what broke - a gate that won’t close for security reasons gets priority over a noisy roller. We’ll give you an honest arrival window when you call, not a vague “sometime today.”
Residential gate replacement in Commerce City typically does not require a permit if you’re keeping the same opening size and location, but check with the city if you’re widening the driveway or changing the gate type. HOA communities like Reunion have their own architectural review requirements, and we can provide the spec sheets and photos your board needs. Call (877) 610-2993 and we’ll walk you through what’s required for your specific property.
Yes. Every gate repair, installation, and welding job we do in 80022 and 80037 carries the 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back - no runaround, no dispatch queue, no “that’s not covered” fine print. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Ready to get your gate working right? Call Gatewood Fence & Gate at (877) 610-2993 for a free estimate. Hal or a live member of his crew will answer, quote your price upfront, and schedule a time that works. No trip charge inside Adams County, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Commerce City Customers Say
"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly