Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Venice
If your gate is sagging, seized, or torn at a weld joint in Venice, you need a repair that accounts for the salt air before it accounts for anything else. Gate parts and welding in this part of town fail differently than they do ten miles inland. Hinge posts rot at the footing, zinc hardware flakes within a few years, and welds fatigue at the heat-affected zone. We fix all of it on site, and we spec the parts to survive the marine layer, not just to get you through the season. Call (877) 610-2993 and Hal or one of our Venice crew will give you a straight answer and a written price before any work starts.
Why Gatewood Fence & Gate Is Venice’s Preferred Gate Parts & Welding Company
Hal Gatewood has been at this since 2001, and his name is on the shop and on every invoice. That matters in Venice, where a lot of the gate work we see is the aftermath of someone who swapped a part, collected a check, and never came back. We do not do that.
Our Gate Parts & Welding crew works Venice from the Canals to the Oxford Triangle, and we have fixed enough gates here to know what the salt air does before we even take the hinge cap off. The person who shows up is background-checked, uniformed, and works for Gatewood, not a subcontractor. We answer the phone with a live person around the clock. Every job carries the 90-Day Done Right Promise in writing. If it is not done right, one call brings us back. No runaround.
We also offer a free second opinion on any written estimate, $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Hal will tell you the same thing he tells every Venice customer: show me the gate closing on its own and I’ll show you where it’s failing.
Our Gate Parts & Welding Services in Venice
Most of the gate work we do in Venice is repair-first. We fix the gate in your driveway rather than hauling it off or swapping parts that don’t need swapping. These are the four services Venice calls us for most.
Hinge Replacement
Hinges take the worst of Venice’s coastal air. Standard zinc-plated barrel hinges on a canal-facing property fail in two to three years, seizing from salt spray and flaking at the pin. We cut out the old hinge, weld in a marine-grade stainless barrel, and set the gate so it swings clear without dragging. A hinge replacement on a typical Venice swing gate runs $180 to $390 per hinge, including welding, depending on gate weight and whether the post needs reinforcement.
Post Replacement
The post is where most gate failures start, not the panel. In Venice, hinge posts set in shallow concrete footings pull loose as the marine layer eats the steel at ground level. Fix the panel without the post and you’ll fix it twice. We dig out the rotted footing, set a galvanized steel post in fresh concrete, and weld or re-hang the gate so it sits true. Post replacement in Venice typically runs $450 to $950, with the higher end covering canal-adjacent lots where we need deeper footings and corrosion-resistant hardware from the first visit.
Rail Repair
Older ornamental iron gates all over Venice, especially on the 1920s and 1940s bungalows off Abbot Kinney’s original streets, crack at the rail-to-picket weld joints. Salt gets into the heat-affected zone and works the crack wider every time the gate swings. We grind out the cracked weld, re-weld with a corrosion-resistant rod, and treat the repair so it does not fail in two winters. Rail repair generally runs $150 to $400 depending on how many joints need work.
Custom Welding
Some Venice gates need a part that does not exist anymore. The ornamental wrought iron from the 1920s and 1930s has no matching replacement parts on a shelf. We fabricate what is missing on site, matching the profile as closely as the original. Custom weld fabrication in Venice runs $150 to $600 depending on the piece, and we show you the price before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Venice
We are certified to service nine major gate brands, and in Venice we see a lot of older Linear and DoorKing operators on 1990s-era slide gates, plus newer Ghost Controls boards on canal-front properties where automation is the only realistic option for a narrow sidewalk setback. We stock common parts for these brands and can order the odd ones fast, which means less downtime for a gate that will not close.
Common Gate Parts & Welding Problems We See in Venice Homes
- Hinge post rot at the footing. The marine layer pushes salt-laden air onshore year-round, and the hinge post is where that salt gathers. The post corrodes at ground level, the gate sags, and the latch no longer lines up. Replacing the post and setting it in a deeper concrete footer is the only fix that lasts near the coast.
- Seized zinc-plated hardware on canal-adjacent properties. The Venice Canals Historic District adds ground-level moisture to the salt air. Standard zinc hinges, strike plates, and latch bolts seize and flake within three years. We default to 316 stainless on every canal-facing job.
- Weld fatigue on original 1920s and 1930s ornamental iron. Venice’s older bungalows still have their original wrought iron, and that iron has decades of salt exposure baked into the metal. The welds at the rail-to-picket joints crack first. Grinding and re-welding with the right rod keeps the gate original instead of replacing it.
- Slide gate rollers corroding at ground level. Beach fog combines with canal moisture on the roller track, causing rough travel and overloading the operator. We see this on the wider lots where slide gates replaced swing gates. Replacing rollers and cleaning the rack before the operator board burns out saves a $400 to $900 part.
Pricing for Gate Parts & Welding in Venice, CA
Here are the ranges you can expect for gate parts and welding work in Venice. Every job gets a written quote before work starts, and that quote does not change at the door.
- Hinge replacement: $180 to $390 per hinge, including welding.
- Post replacement: $450 to $950 depending on depth and corrosion condition.
- Rail repair (weld re-work): $150 to $400 per gate section.
- Custom welding and fabrication: $150 to $600 per piece.
- Full ornamental gate restoration (weld repairs, new hardware, paint prep): $800 to $2,200 depending on gate size and canal exposure.
Venice pricing runs slightly above inland LA on corrosion-prone repairs because we use marine-grade stainless and powder-coated aluminum instead of standard zinc. That specification costs a bit more up front and saves the callback cycle. Call (877) 610-2993 for an exact quote, and remember the price is agreed before any work begins.
We Also Serve Cities Near Venice
If you are a few minutes out of Venice, we still show up. Our crew regularly drives to Santa Monica, Culver City, Ladera Heights, and Century City. The same 90-Day Done Right Promise applies, and we know those neighborhoods nearly as well as we know the streets off Abbot Kinney.
Serving Venice, CA - Our Local Coverage Area
We’re based in the Venice area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Venice
A hinge on a canal-facing property fails faster because it faces two moisture sources at once: the salt-laden marine air from the Pacific and the ground-level humidity off the canal water. Standard zinc-plated hinges seize and flake in two to three years in that microclimate, versus ten-plus years inland. The fix is a marine-grade stainless hinge barrel, and we recommend that spec on every canal-adjacent job. Call us for a free estimate at (877) 610-2993.
In most cases we can weld it. The original wrought iron on those 1920s bungalows is often sound enough to save, even with surface corrosion. We grind out the cracked welds, re-weld with a rod suited to salt-exposed steel, and replace the hinge post if it has rotted at the footing. A full replacement only makes sense if the gate is too far gone structurally, and we will tell you honestly if that is the case. The estimate is free.
Use galvanized steel for the post and 316 stainless for every fastener and hinge barrel. Powder-coated aluminum is also a good option for the gate frame itself because it will not rust the way bare or painted steel will in that double-corrosion environment. We stock both options and can set the post the same visit. Call (877) 610-2993 and we will spec it correctly from the first cut.
316 stainless hinges on a Venice swing gate typically last 15 to 25 years with occasional lubrication, even on a canal-facing property. That is a big jump from the two to three years you will get from zinc-plated hardware. We grease the pins when we install and recommend a light silicone lube once or twice a year, especially during the marine layer season. If you hear squeaking, call us before the pin seizes.
The rack and pinion strips out quickly because canal moisture and beach fog corrode the rollers and the rack teeth at ground level. When the rollers drag, the motor overloads and the pinion grinds against the rack. Replacing the rollers and cleaning or replacing the rack before the operator board burns out is cheaper than replacing the motor later, and we see this pattern constantly on the wider lots where slide gates replaced swing gates.
Call Gatewood Fence & Gate for Gate Parts & Welding in Venice
If your gate is sagging, seized, or cracked at a weld, call (877) 610-2993. Hal Gatewood has been running this shop since 2001, and his crew knows Venice gates the way only people who work on them every week can. We weld on site, we use the right corrosion-resistant spec for the coast, and we put the 90-Day Done Right Promise on every invoice in writing. Free estimates, upfront pricing, and a live person on the phone day or night. The name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Venice since 2001.