Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Orange
If you’re searching for gate parts and welding in Orange, the most common call we get is a gate that sags, drags, or won’t close properly. In Orange’s older neighborhoods, the real problem is rarely the gate panel itself. It’s the hinge post, the welded joint, or hardware that has corroded out years earlier than it should have. We repair what’s there before we ever talk about replacing it, and we do the welding on site so your gate never leaves your driveway. Call (877) 610-2993 and a live person will answer, any hour.
Hal Gatewood started this shop in 2001 and his name is on every invoice. When you call, you get a straight answer about whether that hinge can be welded or truly needs replacing, and a price you can hold us to before any work begins.
Why Gatewood Fence & Gate Is Orange’s Preferred Gate Parts & Welding Company
We’ve worked on enough gates in Orange to know exactly what fails here and why. The 92863, 92864, 92865, and 92866 ZIP codes cover one of the oldest housing stocks in Orange County, from 1880s Victorian homes around the Plaza to 1950s tract houses off Tustin Avenue. That means we’re constantly called to gates hung on masonry pillars that are older than the people living in the house. A gate sags in the hinge post, not in the middle, and that is where we start.
Our Gate Parts & Welding team pulls up to Orange jobs with a welding rig, steel stock, hinges, rollers, and the fasteners that actually hold up in this climate. We don’t send a salesman to look at the gate and then send a different crew two weeks later. Hal or a member of his crew shows up, diagnoses the problem, and fixes it before we leave whenever that’s what the job calls for. Every job carries the 90-Day Done Right Promise in writing: if it isn’t done right, one call brings us back.
We answer the phone with a live person, 24/7. Not a voicemail, not a chatbot. When a Santa Ana wind snaps a hinge weld at 9:00 at night, you get Hal or someone who works for him, and we get you scheduled.
Our Gate Parts & Welding Services in Orange
Hinge Replacement
In Orange, a hinge replacement is rarely just swapping one piece of hardware for another. On older gates, the original hinges were lag-bolted into brick or soft sandstone pillars that have crumbled around the fastener. We rebuild the mounting point, set new anchors, and only then hang the new hinge. On modern steel gates, we weld heavy-duty barrel or ball-bearing hinges right to the frame rather than bolting through thin steel, because bolted hinges on tube steel are the first thing to tear out. A typical hinge replacement on a standard driveway gate in Orange runs $180 to $380 depending on whether the post needs rebuilding and whether welding is required.
Post Replacement
Salt-laden air from the coast moves through Orange’s older neighborhoods and accelerates rust on steel posts, especially on north-facing properties where moisture lingers. We regularly pull posts in Old Towne that look solid from two feet away and are paper-thin at grade level where the galvanizing was ground off years ago. Post replacement in Orange typically means digging to the footing, setting a new galvanized or stainless post in concrete, and re-hanging the gate the same day. You can expect to pay $400 to $900 for a standard residential gate post, more if the pillar is masonry and needs reconstruction to match the period architecture.
Rail Repair
Gate rails take the worst of Orange’s inland heat and Santa Ana wind load. The prolonged dry heat warps redwood and cedar boards faster than most people expect, and screws pull loose from rails within a few seasons if kiln-dried lumber and exterior-grade hardware weren’t specified. We realign, reinforce, and re-fasten rails, and when a rail has rotted or cracked beyond repair, we weld a replacement in place so the gate keeps its original look. Rail repair in Orange generally falls between $150 and $350 depending on the material and how much of the frame needs reinforcement.
Custom Welding
When a gate has a specific dimension, a period style, or damage that no off-the-shelf part will solve, we weld right in your driveway. That includes building new steel frames to match the wrought iron patterns common in Old Towne Orange, reinforcing cracked welds on slide gates damaged by wind, and fabricating brackets for automation retrofits. A custom welding job that doesn’t require removing the gate usually starts around $250. If we need to cut out and rebuild a section, it runs higher, and you get the exact number before we strike an arc. Show me the gate closing on its own and I’ll show you where it’s failing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Orange
If your automated gate was built around FAAC, BFT, Linear, or Viking hardware, we know those systems well enough to repair them without guessing. We stock common replacement parts for these brands so Orange customers aren’t waiting on a shipment from a warehouse while their gate sits open. For older mechanical gates with no operator at all, we carry the hinges, rollers, latch hardware, and steel stock to rebuild what’s there rather than swap in something that looks out of place on a 1920s Craftsman.
Common Gate Parts & Welding Problems We See in Orange Homes
- Rusted-out mild steel hinges on north-facing gates. Orange sits close enough to the coast that salt air pushes inland on the marine layer, and hinges on the shaded side of a house corrode years faster than the same hardware on a south-facing gate. We replace them with stainless or properly galvanized steel, because painted mild steel is a repeat visit waiting to happen.
- Fatigue cracks in welded hinge joints after Santa Ana winds. Gusts through the inland valleys and passes near Santiago Canyon Road regularly exceed 50 to 60 mph, and a swing gate catches that load like a sail. The weld at the hinge plate is where the crack starts. We see a spike in calls after every wind event, and we weld those joints with full penetration rather than a surface bead.
- Crumbled masonry pillars in historic neighborhoods. In Old Towne Orange and the streets around Chapman and Glassell, we pull lag bolts out of brick pillars that have turned to powder behind the fastener. You can’t hang a new hinge in that. The post has to be reconstructed before any other work will hold.
- Warped gate boards pulling loose from rails. The dry heat all through Orange’s inland climate shrinks cedar and redwood gate boards hard, and screws back out of the rails over a few seasons. We re-fasten with exterior-grade fasteners and replace boards that have twisted past the point of holding straight.
Pricing for Gate Parts & Welding in Orange, CA
Here’s what Orange homeowners can expect, based on the work we actually do in this city every month. No trip charge anywhere inside Orange, and the price we quote is the price you pay before we start. Not after.
| Service | Typical Range in Orange |
|---|---|
| Hinge replacement (standard single gate) | $180-$380 |
| Post replacement (steel or wood, set in concrete) | $400-$900 |
| Rail repair or reinforcement | $150-$350 |
| Custom on-site welding (no gate removal) | $250-$600 |
| Full gate rebuild with period-style steel frame | $800-$2,500 |
What moves the number is the condition of the post and the amount of welding involved. A hinge swap on a sound post is quick. A hinge swap on a crumbled 1920s brick pillar is a post reconstruction with a gate re-hang, and the price reflects that. You get a written line-item quote before we touch anything. We offer $40 off any repair over $200, a free second opinion on any written estimate from another company, and a permanent 10% discount for seniors and veterans. Call (877) 610-2993 for an exact quote. Estimates are free.
We Also Serve Cities Near Orange
Our gate parts and welding service covers all of Orange, and we regularly drive out to doors in Orange and the surrounding communities. If you’re in Villa Park, North Tustin, Tustin, or Anaheim, we’ll come out the same way we do here: with a welding rig, the right parts on the truck, and a price agreed before work starts. Dispatch is coordinated from our Los Angeles office, and our crews serve Orange locally.
Serving Orange, CA - Our Local Coverage Area
We’re based in the Orange area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Orange
Yes, if the property is a designated contributing structure and the gate change is visible from the street, the City of Orange requires a Certificate of Appropriateness through its Historic Preservation ordinance before any work can legally begin. This applies to replacement, material changes, and sometimes significant repairs. Skipping it can trigger a stop-work order and fines. No neighboring Orange County city imposes this same layer on routine gate work. We pull the historic property map before quoting any job in Old Towne so you aren’t waiting on paperwork after the gate is already off. Call (877) 610-2993 and we’ll check your property while you’re on the phone.
Orange sits in a band that catches more coastal marine layer than Anaheim or Santa Ana, even though all three cities are within a few miles of each other. Salt-laden air pushes inland through the evening and hangs over Orange’s older, tree-shaded neighborhoods, settling on north-facing metal that never dries fully. Mild steel hinges and latch hardware start pitting in a decade or less. We specify stainless fasteners and hot-dip galvanized or properly primed and painted steel for any Orange job, because we have seen what the uncoated stuff looks like after eight years on a North Shaffer Street gate.
The gate did not sag in the middle; the hinge post moved or the hinge welds cracked. Santa Ana gusts through the Santiago Canyon Road corridor stress swing gates at exactly those two points. The permanent fix is to reset the post with a proper concrete core and re-weld or replace the hinges, then realign the gate in the closed position so it is not fighting the operator or the latch. A temporary cable turnbuckle will hold it for a while, but it masks the post problem until the gate tears the hardware out entirely. For a repair that holds through the next wind season, call (877) 610-2993 and we’ll come assess it.
We weld on site, in your driveway, on nearly every job. Our trucks carry a portable welder, steel stock, and the grinding equipment to cut out cracked sections and weld in solid steel. We only remove a gate for transport when the job calls for heavy fabrication that needs a bench or a jig, and even then it is rare. Welding in place means your gate stays on the property, you can watch the work, and there is no multi-week absence while your driveway sits open. We rebuilt a twisting Craftsman swing gate on North Shaffer Street in Old Towne where the original lag bolts had pulled loose from a crumbling 1920s brick hinge post. Our crew demoed the post to the footing, poured a new core with stainless anchors, and welded a period-style steel frame before re-hanging the gate, all queued behind a Certificate of Appropriateness the homeowner hadn’t known to pull.
In most cases, the original steel gate on a 1950s Orange tract home is worth repairing. The steel is often heavier-gauge than anything you can buy at a big-box store today, and the original welding, while not perfect, is usually still solid where it matters. What fails is the hardware around it: hinges rusted through, posts leaning in old concrete, latch mechanisms worn past adjustment. Replace those components, reinforce the weak welds, and that gate will outlast a new one. We take the repair-first approach because swapping a structurally sound gate for an aluminum box-store panel is how homeowners end up paying twice. For an honest assessment on your specific gate, call (877) 610-2993.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Orange and surrounding communities since 2001.