Gate Parts & Welding in Norwood - Made to Measure, Written Price

Fast, Reliable Gate Parts & Welding Across Norwood

Gate parts and welding in Norwood comes down to two questions: is the post still sound, and is the hardware worth saving? Most of the time, the answer to both is yes, and that’s exactly where we start. A hinge replacement on a 1960s wrought-iron gate near the Town Common runs $225-$395. A post replacement with a proper 48-inch footing runs $680-$1,150. We’re Gatewood Fence & Gate, owner-operated since 2001, and we weld on site in your driveway so the gate never leaves your property. Hal Gatewood’s name is on the shop and on every invoice. Call (877) 610-2993 and a real person picks up, day or night.

Call (877) 610-2993

Why Gatewood Fence & Gate Is Norwood’s Preferred Gate Parts & Welding Company

Norwood’s gate stock is older than what you’ll find in Westwood or Canton. We drive the same streets you do: Washington Street past the hospital, Nahatan Street through the industrial stretch, the side roads off Route 1A where the salt spray coats everything in February. That matters when you’re deciding whether to repair or replace a gate. A company focused on Gate Installation - Norwood might not carry the period-appropriate iron strap hinges a Victorian near the Common needs. We do.

We’re locally owned and owner-operated, not a franchise with a rotating crew. Hal has been fixing gates since 2001, and the person who shows up is either Hal himself or someone from his crew who answers to him directly. Every job, from a welded post repair to a full roller and track replacement on a University Avenue sliding gate, carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back.

Beyond the work, there’s the phone. You call us, a live person answers, 24 hours a day, seven days a week. No voicemail tree, no call center. You want to talk to Hal, you drive to the shop and look him in the eye. That’s the oldest accountability there is.

Our Gate Parts & Welding Services in Norwood

We handle the whole range of Gate Parts & Welding, but here’s what Norwood homeowners and facility managers call us for most often.

Hinge Replacement

A gate sags in the hinge post, not in the middle, and that’s where we start. On Norwood’s post-war capes and colonials, the original hinge hardware was often welded onto thin-wall square tube. Forty years of freeze-thaw cycles work-harden the welds until they crack. We cut out the old hinge, dress the post, and weld on new hardware rated for the gate’s actual weight. Typical hinge replacement in Norwood runs $180-$340 per gate, including realignment.

Post Replacement

This is the big one in Norwood. Mass code calls for a frost footing around 48 inches deep, and most gates installed before 1970 are sitting on 24 to 30 inches of concrete. That’s the root of half the sagging-gate complaints we hear every March. We dig out the old post, pour a new 48-inch footing, and set the post plumb. Post replacement with new footing runs $680-$1,150 for most Norwood driveways, depending on gate weight and what we encounter underground.

Rail Repair

Rails take abuse in Norwood. Residential gates catch wind off the Neponset watershed, and commercial gates on University Avenue absorb daily truck traffic. A bent or cracked bottom rail is usually weldable in place. If the rail is rusted through, we’ll section in new steel and re-powder coat where feasible. Rail repair typically runs $160-$390.

Custom Welding

Some Norwood gates were built in someone’s garage forty years ago and were never really square. Others are ornate iron picket gates on Victorian homes near the Town Common that need a hinge fabricated to match the original pattern. We do ornamental and structural welding on site. Custom work is quoted by the hour of weld time plus material, and you get the number before we strike an arc.

Trusted Brands We Service in Norwood

If your Norwood Gate Motor & Opener carries a Viking, Ghost Controls, or DoorKing nameplate, we stock the common boards, limit switches, and receiver parts to keep them running. We’re certified to service nine major gate brands, and for Norwood customers that means we usually have the part on the truck or at the shop within a day or two. When we don’t stock it, we order it directly rather than upcharging through a middleman. Same welding truck, same route, residential in the morning and the University Avenue commercial corridor in the afternoon.

Common Gate Parts & Welding Problems We See in Norwood Homes

• Frost-heaved posts. Norwood’s winter freeze-thaw cycles, especially in the low ground near the Neponset River, push shallow footings up an inch or more. Your gate was fine in November, and now the latch won’t meet the striker in April. We fix the post, not the symptom.
• Seized bottom rollers on industrial sliders. The sliding gates along University Avenue and Nahatan Street get road salt tracked in from Route 1A. It corrodes rollers and ground track until the gate binds and the operator strips. We carry replacement rollers and track sections on the truck for those accounts.
• Hinge welds cracking on 1960s square-tube gates. The original welds were never meant to survive fifty New England winters. We grind out the failed weld and re-weld with proper penetration, then reinforce if the tube wall is thinning.
• Legacy operators failing without safety protection. 1990s openers on Norwood gates often predate current entrapment standards. If we can retrofit a compliant edge and board we will. If we can’t, we’ll tell you straight because a gate that closes on an unsupervised child is a repair that isn’t worth doing halfway.

Pricing for Gate Parts & Welding in Norwood, MA

We Also Serve Cities Near Norwood

While this page is about Norwood, our crew regularly handles gate parts and welding in Westwood, Canton, Walpole, and Dedham. If you’re in one of those towns, our Gate Parts & Welding in Norwood scheduling covers your next call with the same no-trip-charge policy inside the county.

FAQs - Gate Parts & Welding in Norwood