Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Gainesville, TX
Gate repair in Gainesville typically costs $140-$520 for most residential fixes, with agricultural and ranch gate work running higher due to heavier pipe and hardware. We answer live at (877) 610-2993 around the clock, and we show up in the window we give you. If your gate is sagging, dragging, or refusing to open after last night’s freeze, we’ll tell you straight what’s wrong and what it costs before we touch anything.
Why Gainesville Homes Are Different
Gainesville sits squarely in working ranch country at the edge of the Red River corridor, and that shapes every repair call we get. A large share of our work here involves agricultural and livestock gates on rural acreage properties - swing-pipe, tube-steel, and cable-latch pasture gates that get opened by hand, by tractor, and by half-ton pickups. These aren’t ornamental driveway gates with quiet closers. They’re working equipment, and they fail from load stress, rust at the hinge barrels, and latch hardware worn loose for years.
The soil makes it worse. Cooke County is notorious for expansive shrink-swell clay. After a wet spring followed by a dry summer, footings can heave or tilt several inches, throwing automatic swing-arm operators completely out of travel alignment. Re-plumbing the post is almost always required before any electronic or mechanical repair will hold long-term.
Then there’s the winter. Gainesville sits in North Texas’s I-35 ice belt, where freezing rain coats gate hardware, seizes automatic operators, and adds enough load to stress hinges and weld joints on large swing gates. Summer heat and UV accelerate powder-coat failure, while Red River corridor wind events can catch an unlatched swing gate like a sail and shear hinge pins outright.
We work all over Gainesville, from the Victorian and craftsman homes near the downtown square to the post-war ranch houses along Weaver Street, and out into the acreage tracts east toward Callisburg and north toward the Red River. Typical response time is same-day for emergency repair calls, and we’ll always tell you the actual window before you commit to waiting around.
Gate Repair in Gainesville
Gate repair in Gainesville usually means one of two things: a pasture gate off its hinges on an acreage property, or an automatic driveway gate that quit after the last ice storm. We handle both. Hal Gatewood has been fixing gates since 2001, and a live person answers our phone around the clock. If your gate is sagging, binding, or not opening at all, call (877) 610-2993 and you’ll talk to someone who can tell you when we’ll be there and what it’ll cost.
The repair profile in Gainesville is meaningfully different from the suburban gate market 40 miles south in Denton. Rural acreage gates see heavier use, harsher exposure, and decades of deferred maintenance. Our repair-first philosophy means we weld on site rather than haul your gate to a shop, and we fix what other companies want to replace.
Electric Gate Repair
When an electric gate in Gainesville won’t open or won’t close, the cause is usually the operator itself, the safety sensors, or the post it’s mounted to. Given the shrink-swell clay around here, post movement is the one people miss - we diagnose the whole system before we sell you a part. If the board is fried, we replace it. If a wire got chewed by field mice in a junction box, we splice it right. Electric gate operator repair in Gainesville runs $180-$475, parts included, and every repair carries the 90-Day Done Right Promise in writing.
Hinge and Post Repair
A gate sags in the hinge post, not in the middle. In Gainesville, where many posts are set in Cooke County’s expansive clay, that post can tilt after a wet spring followed by a dry summer. Re-plumbing the post is almost always required before any electronic or mechanical repair will hold. We cut the old post free, dig and pour a new footing, weld on fresh hinge plates, and hang the gate straight. On-site welding means the gate stays in your driveway - we don’t haul it to a shop. Hinge and post repair in Gainesville runs $220-$520, depending on post condition and whether we’re re-pouring a footing.
Gate Realignment and Weld Repair
Realignment is not just tightening bolts. It’s getting the leaf square in its frame, level at the latch, and full-travel at the operator. On shared driveways and rural rights of way throughout Gainesville’s 76240 and 76241 zip codes, two property owners often split maintenance duties, and neither one noticed the gate dragging until it stopped latching. We re-set the alignment, service the hinges, and adjust the operator so both neighbors can get in and out. Gate realignment runs $120-$280, and weld and rust repair runs $90-$340 based on crack length or panel condition. For more on our repair approach, see our Gate Repair page.
Why does my gate post keep tilting in Gainesville, and can you fix it permanently?
Your post is likely set in Cooke County’s expansive clay, which swells when wet and shrinks when dry, heaving the footing out of plumb. We fix it permanently by digging out the old footing, setting the post in a deeper concrete pour with proper drainage, and welding the hinge assembly back square. A repair on the existing footing will just tilt again. Call (877) 610-2993 and we’ll come look at it free.
My automatic gate opens halfway and reverses - is that the operator or the post?
It’s usually the post. When the hinge post leans, the gate binds mid-travel and the operator’s entrapment protection kicks in and reverses it. Re-plumb the post first, then test the operator. We’ve fixed this exact problem repeatedly on rural acreage properties around Gainesville, and the motor often runs fine once the geometry is corrected.
Gate Installation in Gainesville
A new gate in Gainesville usually runs between $1,400 and $8,500 installed, depending on whether you’re hanging a single tube-steel pasture gate or automating a double driveway gate off I-35. We work those numbers out with you before anything gets ordered. The crew that shows up at your place in Gainesville is the same crew whose name is on the invoice - no subcontractors, no surprises.
Gainesville’s housing stock shapes what we install. Early-20th-century craftsman and Victorian homes near the downtown square need gates that match their scale and detail. Post-war ranch houses along Weaver Street and newer construction along the I-35 corridor have different driveway grades and setback constraints. Rural acreage lots on the outskirts often need working gates sized for hay trailers and stock haulers, not just passenger vehicles.
Driveway and Swing Gate Installation
Driveway gates on acreage lots east and west of Gainesville frequently need a double gate rather than a single wide leaf, simply because the opening was cut to accommodate hay trailers and stock haulers. We measure the driveway as it actually is, not as county records say it should be. A standard single-leaf driveway gate in Gainesville runs $1,400-$4,200 installed, while double gates start at $3,200. An automated ornamental double swing gate with operators usually lands between $5,000 and $9,000.
Sliding Gate Installation
Sliding gates make sense on Gainesville properties where the driveway slopes toward a limestone cut or where an irrigation ditch runs too close to the swing arc. Instead of fighting the grade, the gate rides on a track and stays off the mud. A sliding gate in Gainesville typically costs $2,800-$7,500 installed, with motor and track hardware included. Cantilever sliding gates, which don’t need a ground track, cost more up front but won’t bind when clay soil swells in a wet spring.
Pedestrian Gate Installation
A pedestrian gate is the one you’ll use fifty times a week, so it gets the hinges and latch that survive that. We install them beside driveways, into side-yard fences, and as standalone entries into fenced pastures around Gainesville. Most pedestrian gates run $600-$1,500 complete with posts. If you’re putting one in on an older Victorian or craftsman home near the downtown square, we match the frame style so the gate doesn’t look like an aluminum afterthought bolted onto a 1910 fence. For more installation options, see our Gate Installation page.
How do Gainesville prices compare to Denton or Sanger?
Rural Cooke County jobs sometimes cost a little less than the same job in Denton because there’s less permitting and fewer setbacks to work around. But the real cost driver is the opening itself. A wide hay-trailer gate with a sliding track will cost more than a standard driveway swing gate in town. We quote every job on site, free, and the number we give is the number you pay.
Does your work come with a warranty in Gainesville?
Every install carries the 90-Day Done Right Promise in writing. If it’s not right, Hal comes back. No arbitration, no “in most cases.” One call brings him out. After that, the hinges, posts, and welds are built to last years, not months. If your gate in Gainesville is sagging, twisted, or gone entirely, call (877) 610-2993 for a free measure and written price.
Gate Motor & Opener in Gainesville
When a gate motor gives out on a Cooke County morning, you don’t have time to wait on hold. We run crews into Gainesville, 76240 and 76241, for gate motor repairs and replacements, and we come prepared for the particular ways gates fail out here: clay-heaved posts, ice-stressed arms, and aging tube-steel frames on acreage that hasn’t seen service in years. Hal still diagnoses motors himself rather than defaulting to replacement.
The motor is rarely the only problem. A LiftMaster swing arm that opens partway and reverses is often fighting a hinge post that’s leaned out of plumb from seasonal clay movement. Our crew saw exactly that on a rural property near the Red River corridor - the post had heaved several inches after a wet spring and dry summer. We cut the operator loose, re-plumbed the post with new concrete, reset the travel limits, and the motor ran quiet for years.
Motor Installation and Replacement
A new gate motor in Gainesville means matching the opener to the gate’s actual weight, swing direction, and the way the post sits in Cooke County clay. We measure, we don’t guess. A motor sized for a light driveway gate will burn out in months trying to swing a heavy pipe gate on an acreage entrance. We install LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we set the travel, force, and safety sensors correctly the first time. A full operator replacement runs $850-$1,700 installed for most residential gates, while slide motors on long ranch gates run $1,200-$2,300.
Motor Repair and Diagnosis
We repair what other companies want to replace. A noisy motor is often just a worn drive gear or a bad capacitor, not a reason to sell you a whole new opener. In Gainesville, we see a lot of motors that were fine internally but failed because the post shifted out of travel alignment. We fix the post, re-set the travel, and the motor runs quiet. A typical motor repair lands between $180 and $420 depending on brand, and a service call to diagnose a dead motor runs $90-$140 with no trip fee inside Cooke County.
Linear and Slide Motor Service
Linear gate motors with threaded drive shafts show up all over the I-35 corridor from Gainesville to Sanger. When a drive shaft gets bent or its grease goes dry in a North Texas summer, it binds and the motor overheats. We service and replace linear motors from Linear, FAAC, and BFT, and we keep common parts stocked so we’re not waiting on a shipment while your gate sits open. For slide gates on long acreage drives, we set rack and pinion alignment, replace worn bearings, and make sure the motor’s gearbox isn’t fighting a track that’s out of level. See our Gate Motor & Opener page for more.
How much does a gate motor repair cost in Gainesville?
Most motor repairs in Gainesville land between $180 and $420, while a full operator replacement runs $850-$1,700. A new motor installation on a ranch gate starts higher because the gates are bigger and alignment work takes longer. We quote every job upfront, in writing, and we honor it. Call (877) 610-2993 for a free estimate.
What does a full gate motor installation include?
A complete installation includes the motor, swing arm or slide rack, mounting hardware, wiring to the control board, safety sensor setup, travel and force calibration, and a final walk-through. For Gainesville properties with clay-prone posts, it also includes checking the post for level and telling you plainly if it needs re-plumbing before the motor goes on. Every installation carries the 90-Day Done Right Promise in writing.
Gate Access Control in Gainesville
Gate access control in Gainesville means keeping ranch gates, driveway operators, and keypads working on properties where the nearest supply house is 40 minutes away and a dead gate means cattle get out or the horse trailer can’t get in. We repair and install keypad entry, remotes, phone entry, card readers, video intercoms, and smart access systems across Gainesville, including the 76240 and 76241 zip codes. The person who answers the phone can tell you when we’ll be there and what it’ll cost.
Many rural acreage properties still run original DoorKing or FAAC control boards from 20-plus years ago. Humidity, summer heat, and ice exposure wear out capacitors and relays, leaving the gate dead and the keypad unresponsive. We stock common parts and can often get legacy systems running without a full replacement.
Keypad and Remote Entry
Keypad entry on Gainesville ranch gates takes a beating that suburban keypads never see - dust, ice, cattle rubbing against the post, direct summer sun on a metal housing. We install wired and wireless keypads rated for outdoor exposure, and we always check the post it’s mounted to. A keypad on a leaning post will misalign with the strike, and no amount of code-punching fixes that. Keypad installation runs $350-$600 for wired units integrated with existing operators, or $250-$450 for wireless. New remote programming is $75-$150, with long-range ranch remotes at $95-$175 each.
Phone Entry and Card Readers
Phone entry systems let you buzz open the gate from your cell phone without a separate remote, which is why a lot of Gainesville ranch owners add them for delivery trucks, feed suppliers, or family members. We install modules that tie into existing operators and actually call you when someone presses the button - not an app that might work. Phone entry modules start around $450 installed. Card readers make sense for properties with multiple drivers or employees, and run $500-$900 for a single gate depending on wiring distance.
Video Intercom and Smart Access
Video intercoms give you eyes on the gate before you open it, which on a dark Cooke County road is a genuine safety feature. Smart access keeps event logs and lets you grant or revoke access from anywhere. Gainesville’s rolling acreage can make Wi-Fi range a real headache for smart controllers, so we check signal strength at the gate before recommending a Wi-Fi-dependent system. If the signal won’t reach, there are cellular-based options. Video intercom installation runs $700-$1,200 for a single entry point. Learn more on our Gate Access Control page.
Can we retrofit solar gate openers to old pasture gates without power?
Yes, and it’s one of the most common upgrades we do on rural acreage properties around Gainesville. A solar-powered operator with battery bank and panel can run a swing gate or tube-steel pasture gate without running utility lines across the pasture. Solar gate opener retrofits start around $1,200-$1,800 installed, depending on gate size and hinge and post condition.
Why does my gate keypad work fine in spring but not after a dry summer?
The keypad isn’t the problem - the post moved. Cooke County’s shrink-swell clay dries and contracts in summer, tilting the gate post and changing alignment between the keypad-mounted strike and the latch. The fix is re-plumbing the post and re-aligning the gate and strike. Call (877) 610-2993 and we’ll diagnose it free.
Gate Parts & Welding in Gainesville
Gate parts and welding repair in Gainesville typically runs $175-$650 for hinge replacement, $400-$1,100 for post replacement with concrete footing work, and $150-$450 for rail repair. Most jobs are completed on-site the same visit. If you have a sagging pasture gate off FM 51 or a rusted tube-steel driveway gate in the 76240 ZIP, our crew can be at your property fast, and we quote the price before any work starts.
Hal has been welding since 2001, and he’ll build brackets, gussets, mounting plates, or latch reinforcement right there at your gate. On a ranch off FM 372, our crew found a 14-foot tube-steel swing gate hung in the 1980s with a single failing hinge post set in cracked clay. We cut out the rusted post, augured a new footing below the heave line, welded a replacement post with gusset plates, and saved the customer a full gate replacement.
Hinge and Post Replacement
Most sagging gates in Gainesville aren’t bent. The hinge post has moved. In Cooke County, shrink-swell clay under older hinge posts heaves and tilts with the seasons, throwing swing gates out of alignment and wearing hinge barrels unevenly. We cut out the old hinge, weld a reinforced replacement with gusset plates, and set it to correct the sag. Hinge replacement on a 12- to 16-foot tube-steel gate runs $175-$350 including on-site welding. Post replacement with new concrete footing runs $400-$1,100 depending on depth and gate size.
Rail Repair and Custom Welding
Tube-steel gates rust from the inside out, especially along the bottom rail where water sits after a wet North Texas spring. We see this on older Gainesville acreage properties: the bottom rail is rusted through, but the rest of the frame is sound. We cut out the rotted section and weld in new rail stock matched to the original tube size. Rail repair generally runs $150-$450. Custom bracket or mounting plate welding runs $75-$250. You don’t need a new gate because one rail failed. For more on our welding capabilities, visit our Gate Parts & Welding page.
Is it cheaper to replace just the hinge post, or should I replace the whole gate?
In Gainesville, replacing the hinge post is nearly always the cheaper fix, and it’s usually the right one. If the gate frame is still sound, post replacement runs $400-$1,100. A full gate replacement for a 14- to 16-foot tube-steel swing gate can run $2,500-$5,000 or more. We only recommend full replacement when the frame has rusted through or twisted beyond straightening.
My old tube-steel gate has rusted-through bottom rails. Can you weld in new sections?
Yes. We cut out the rotted section of the bottom rail and weld in new tube stock matched to the original size and wall thickness. The weld is as strong as or stronger than the surrounding steel, and we make sure the inside of the rail is dry and coated before we close it up. This is routine work on older Gainesville acreage gates. Call (877) 610-2993 for an exact quote.
Brands We Service in Gainesville
We’re certified to service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for Linear, Viking, and Ghost Controls operators locally, which means most repairs don’t wait on shipping. For a full list, see our brands page.
Pricing for Gate Repair in Gainesville, TX
| Service | Typical range in Gainesville |
|---|---|
| Hinge and post repair | $220-$520 |
| Gate realignment | $120-$280 |
| Electric gate operator repair | $180-$475 |
| Automatic gate troubleshooting / sensor repair | $110-$260 |
| Weld and rust repair | $90-$340 |
| Single driveway swing gate (installed) | $1,400-$4,200 |
| Double driveway gate (installed) | $3,200-$7,800 |
| Sliding gate with motor (installed) | $2,800-$7,500 |
| Pedestrian gate (installed) | $600-$1,500 |
| Gate motor repair | $180-$420 |
| Full operator replacement | $850-$1,700 |
| Keypad entry (wired) | $350-$600 |
Prices push higher in Gainesville when posts need full re-plumbing in heaving clay, when gates are sized for hay trailers or stock haulers, or when automation is added to an existing manual installation. Every price is quoted and agreed before any work starts - not after, not at the door. No trip charge inside Cooke County, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
Neighborhoods We Serve in Gainesville
We work across Gainesville’s full range of neighborhoods and property types, from historic homes to working ranches. Same-day response is available for emergency calls throughout the area.
- Downtown Gainesville historic district - Victorian and craftsman homes near the square
- Weaver Street and the older east side - post-war ranch houses with original fencing
- Acres north along Highway 82 toward the Red River - rural properties with livestock gates
- South side near North Central Texas College - newer construction and student rentals
- East toward Callisburg - acreage tracts with tube-steel and pipe-framed pasture gates
Service Area - Cities Near Gainesville
We serve Gainesville, TX and surrounding communities throughout Cooke County and the I-35 corridor. Our crews also work in Sanger, TX, Celina, TX, Denton, TX, Prosper, TX, and Little Elm, TX. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, with crews serving Gainesville locally.
Serving Gainesville, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Gainesville and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Gainesville coverage area; if your address is on it, we can help.
Also serving nearby: Gainesville, TX, Sanger, TX, Celina, TX, Denton, TX, Prosper, TX, Little Elm, TX.
FAQs About Gate Repair in Gainesville
Residential gate permits in Gainesville depend on whether you’re modifying an existing fence line or installing a new structure with electrical automation. Cooke County generally has fewer restrictions than Denton or Collin County, but we always check local requirements before we start. If a permit is needed, we’ll tell you upfront and help with the paperwork.
For a gate that’s down with livestock behind it or a property left unsecured, we make Gainesville a priority same day. A live person answers the phone 24/7, and the person who shows up knows the difference between a gate on FM 372 and one in the hills off County Road 200. Call (877) 610-2993 and tell us what’s happening.
Yes. We install and repair gates throughout 76240 and 76241, from the older neighborhoods near the downtown square to the acreage lots off I-35 and east toward the Red River corridor. Rural properties with long gravel drives and pipe-framed pasture gates are a big part of our work in the area. There’s no trip charge inside the county.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Gainesville Customers Say
"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks