Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Briar, TX
Gate repair in Briar typically costs between $185 and $740 depending on whether we’re resetting a post, rebuilding a hinge, or replacing an operator. Most jobs are completed in one visit, and we quote the price before any work starts. If your gate is dragging on a caliche driveway off Briar Road or stalling halfway across a pasture entrance, call (877) 610-2993 and we’ll get a truck out to you.
Briar is an unincorporated Wise County acreage community, not a grid of subdivisions. That means every gate call we answer is on a property with some land, and the dominant gate type is a long-driveway ranch or automated swing gate on a rural residential lot. The primary failure driver here is Wise County’s notorious shrink-swell Vertisol clay, which heaves and tilts gate posts seasonally until frames rack, hinges bind, and automated arms stall. Any gate repair business serving Briar must be built around post-reset and alignment work tied to the clay cycle, not simple hardware swaps.
Why Briar Homes Are Different
Briar consists largely of acreage ranchette-style properties developed in waves from the 1980s through the 2020s as Fort Worth exurban sprawl pushed into Wise County. Most lots feature long gravel or caliche driveways with pipe-frame ranch gates or electric driveway operators, swing-arm or slide-track. There is virtually no dense urban housing stock, so almost every job we do involves a freestanding driveway gate rather than an attached fence gate.
The local climate makes this work distinct. Wise County’s heavy expansive clay soils shrink dramatically during the brutal summer droughts that regularly grip North Texas, then re-swell with fall and spring rains. That cycle tilts gate posts, shifts concrete footings, and racks frames out of square multiple times per year. Briar also sits in the North Texas ice-storm corridor where freezing rain events seize gate operator gearboxes, shatter plastic limit-switch housings, and weld hinges shut more reliably than areas closer to the DFW urban heat island.
Local techs know that the first significant fall rain after a dry North Texas summer triggers a cluster of same-week service calls across Briar. The clay swells all at once, and swing-gate arms that cleared their stops in August suddenly stall mid-travel or drag the gate into the ground. This is a Wise County clay-cycle phenomenon that neighboring Tarrant County subdivisions with engineered slabs and concrete fence panels almost never see.
Gate Repair in Briar
When a driveway gate stops opening in Briar, it’s rarely a simple hinge. What you’re usually dealing with is a post that has moved, a frame that has racked out of square, or an opener arm that’s now fighting the ground because the clay underneath shifted again. We get the call, we drive out to your place off Briar Road or along County Road 4685, and we fix the actual problem instead of masking it. A live person answers at (877) 610-2993 any hour, day or night.
Electric Gate Repair
Electric gate operators around Briar take a beating from the ice-storm corridor that runs through this part of Wise County. We service FAAC, BFT, Linear, and Viking operators, and we carry control boards and limit-switch parts for most 1990s and 2000s units. When a gearbox seizes after a freezing rain event, the repair usually runs $260 to $520 depending on whether it’s a gear replacement or a full operator swap.
Hinge and Post Repair
A gate sags in the hinge post, not in the middle, and that’s where we start. On Briar ranchette properties, pipe-frame gates hung from posts set decades ago in expansive clay are especially prone to this. We dig out the old footing, pour a bell-bottom base that resists the heave cycle better, and weld the hinge back to plumb. Depending on the post size and how much excavation is involved, you’re looking at $210 to $480 per post.
Gate Realignment
When a swing gate drags across the caliche or catches on the catch post, forcing it shut just bends the frame worse. We re-square frames in the field, often on-site, without hauling your gate to a shop. On a 14-foot ranch gate, realignment and frame reinforcement usually runs $190 to $390, and we weld on-site so the gate stays where it belongs: on your property.
We’ve been doing this long enough to know that fixing the panel without the post means you’ll fix it twice. That’s why our Gate Repair approach starts with the post and the ground under it. Every job carries our 90-Day Done Right Promise in writing, and we take $40 off any repair over $200.
Why does my swing gate work all summer and then stall after the first big fall rain in Briar?
The first significant fall rain after a dry North Texas summer causes Wise County’s expansive clay to swell all at once, tilting gate posts and racking the frame out of square. The operator’s internal travel limits then no longer match the gate’s actual movement, so the arm stalls mid-travel or drags the gate into the ground. This is a clay-cycle phenomenon we see clustered across Briar every year, and we fix it by re-setting the post and re-squaring the frame, not by throwing a new motor at it. Call (877) 610-2993 for an exact quote.
How do I know if my gate’s hinge post needs to be reset instead of just welding the sag out of the frame?
If the gate sags at the latch end but the post itself is visibly leaning, or if you can see daylight shifting between the hinge leaves and the post, the post is the problem. A chain stretched taut at the top but slack at the bottom is another tell. In Briar’s clay, a tilting post will just tilt again next season if you don’t re-pour the footing with a bell-bottom base that resists the heave cycle. We’ll show you exactly what’s happening and quote the repair before we dig. Call (877) 610-2993 for a free estimate.
Gate Installation in Briar
Gate installation in Briar means building for long gravel driveways, wide ranch entrances, and Wise County clay that heaves every season. Most homes here sit on acreage, not suburban lots, so the gate has to span wider, carry heavier pipe frames, and run reliably on solar power where utility lines never reach. We’ve been setting posts and hanging gates on Briar properties long enough to know that if the footing isn’t deep enough and the operator isn’t sized right, you’ll be calling us back within two seasons.
Driveway Gate Installation
A long driveway off County Road 4795 or any of the caliche tracks winding through Wise County usually needs a gate that spans 12 to 20 feet and carries real weight. That’s where the power and span problem shows up: a lightweight opener rated for a suburban ornamental gate will stall on a pipe-frame ranch gate within a season or two. We size the operator for the weight and wind load, not just the opening width. A single swing gate, 12-16 feet, manual, typically runs $1,800 to $3,200 installed.
Swing Gate Installation
Swing gates are common on Briar ranchettes because they’re cheaper than slides and handle wide openings well when space allows. The catch is that a swing gate hangs every pound on the hinge post, so that post has to be deep and set in concrete that goes below the shrink-swell zone. When we install swing gates in Briar, we dig past the clay line, set the post, and use an operator with enough torque to move the gate even when hinges bind slightly after a wet fall. A swing gate with operator, 12-16 feet, typically runs $3,800 to $6,500.
Sliding Gate Installation
Sliding gates make sense on Briar lots where the driveway slopes or where the gate would swing across a ditch. The track is the weak point. Caliche driveways and expansive clay combine to create ruts that jam the rack and pinion, and when the track binds, the operator burns out trying to push through it. Our sliding gate installation in Briar includes building the track bed flat, setting the rollers above the grade where debris won’t collect, and choosing an operator with enough push force for the gate’s weight. A sliding gate with operator, 16-20 feet, typically runs $5,500 to $9,000.
Every Gate Installation quote we give in Briar is written and agreed before work starts. That price is the price. No trip charge inside the county, free estimates, and a permanent 10% discount for seniors and veterans.
Why do gate posts shift so much in Briar after a dry summer?
Briar sits on Wise County’s expansive Vertisol clay, which shrinks dramatically during summer droughts and swells when fall rains return. That shrink-swell cycle heaves posts set in shallow holes out of plumb, tilting the gate frame until hinges bind and operators stall. The fix is setting posts below the clay movement zone, which we do as standard practice on every installation in the 76071 area. Call (877) 610-2993 for a free measure and written quote.
Can I power a gate operator at the end of a long Briar driveway without running utility power?
Yes. Solar operators with battery backup are the standard solution for Briar acreage where trenching utility lines to the gate would cost more than the gate itself. We size the panel and battery bank for Briar’s cloudy winter weeks and ice storm outages, not just sunny days. A solar operator add-on, battery and panel, typically runs $900 to $1,800. Call (877) 610-2993 and we’ll spec it for your driveway.
Gate Motor & Opener in Briar
When your gate motor quits in Briar, you’re not dealing with a minor inconvenience. You’re dealing with a long driveway, a vehicle stuck on the wrong side, and a property that suddenly lost its first line of security. Most gate motor failures we see in Briar follow a familiar pattern: the motor hums but the gate won’t move, or the gate opens halfway and stalls, or it reverses on its own after closing.
Motor Installation
Installing a new gate motor in Briar starts with evaluating the post itself. If the post has been heaving with the clay cycle, bolting a new motor onto it just transfers the problem to the new unit. We check post plumb and frame square first, then mount and calibrate the operator so the gate travels clean through its full arc. A typical installation on a Briar driveway gate runs $950 to $2,400 depending on motor brand, gate weight, and whether we’re adding a battery backup or intercom integration.
Motor Repair
Most motor repairs in Briar fall into a handful of categories: burned control boards, stripped drive gears, failed limit switches, or water intrusion from a bad seal. We diagnose the specific fault, replace only what’s actually broken, and test the full travel cycle before we leave. Most repair calls in Briar run $180 to $520, and the price is quoted and agreed before we touch a single bolt.
Slide Motor Service
Slide gates are popular on Briar acreage lots because they don’t require the gate to swing across a gravel or caliche drive that may have deep ruts. But slide motors depend on a straight, level track. When the ground shifts, the gate binds and the motor overheats. We service slide motors from BFT, Viking, FAAC, and others, including roller replacement, track leveling, and motor gearbox service. Expect $220 to $680 for most slide motor repairs in Briar.
We also know that sometimes the motor isn’t the actual problem. A gate that sags in the hinge post, not in the middle, will kill a motor just as surely as a lightning strike. That’s why our Gate Motor & Opener service always starts with the mechanicals, not the electronics. Every repair carries the 90-Day Done Right Promise in writing.
Do Briar gate motor repairs cost more than in nearby cities?
No. Our pricing is the same across North Texas. A motor repair in Briar runs the same $180 to $680 it would run in Saginaw or Keller. What changes is the diagnosis: Briar’s clay soil and ice-storm exposure mean we check post alignment and water seals on almost every call here, and that’s built into the upfront quote, not added later. Call (877) 610-2993 for an exact quote.
What does a full motor installation include in Briar?
A full installation includes post alignment inspection, frame square check, motor mounting, travel calibration, safety edge or obstruction sensor setup, and a full test cycle. We quote the entire job in writing before work begins, and the price doesn’t move unless you add something to the scope. A typical Briar installation runs $950 to $2,400 depending on gate type and motor brand. Call (877) 610-2993 to schedule.
Gate Access Control in Briar
Gate access control in Briar means keypads, remotes, phone entry, and card readers on long-driveway ranch gates and automated swing gates. Most Briar calls we get are for older LiftMaster, Viking, or FAAC operators that stopped responding after a rain or a freeze, not brand-new installs. Hal Gatewood has worked on gates like yours since 2001, and he still picks up the phone himself.
Keypad Entry
Most Briar ranch gates we see either have no keypad at all or have one from the 1990s with corroded wiring at the post base. Water collects where the conduit meets the concrete, and Briar’s clay soil holds that moisture against the connections for weeks. We install new keypads and repair the wiring path properly, with sealed conduit and strain relief so you’re not replacing the same keypad in three years. A typical keypad entry system runs $380 to $650 installed.
Remote Control
Adding remote control to an older electric gate in Briar is usually straightforward when the operator still has a receiver, and a headache when it doesn’t. Older LiftMaster and Mighty Mule operators often have a receiver built in, so it’s a matter of programming remotes. For older FAAC or BFT boards that predate wireless, we add an external receiver. Either way, expect $220 to $420 for the work, including remotes. We program and test them in front of you.
Phone Entry Systems
Phone entry systems let a driver call a number from the gate and you buzz them in from your cell phone, wherever you are. On Briar’s larger acreage lots, where the house might be a quarter mile from the county road, that’s a real convenience, not a gadget. A basic phone entry system starts around $900 installed. A video intercom option pushes it higher, typically $1,300 to $1,900.
We’ll tell you honestly whether a video intercom is worth it on your property, because sometimes a good keypad and a driveway sensor is the smarter spend. That’s the difference with Gate Access Control from a local shop: we don’t sell you what you don’t need. Every price is quoted and agreed before any work starts.
Why does my Briar swing gate stop working right after the first big fall rain, even though it worked all summer?
It’s the Wise County Vertisol clay. During the summer drought, the clay under your gate posts shrinks and the posts can shift outward. Then the first big fall rain hits and the clay swells all at once, lifting and tilting the posts in a different direction. The hinge post moves, the safety photocells drift out of alignment, and the operator faults out mid-travel or drags the gate into the ground. We fix the post, realign the photocells, and recalibrate the operator so it survives the next cycle. Call (877) 610-2993.
Can you add keypad entry or remote control to an old manual pipe-frame ranch gate in Briar?
Yes, in most cases we can. The gate needs solid posts and a frame that’s still square, but we can add a motor, a keypad, and remotes to many older pipe-frame gates. We’ll also install the safety photocells and set the force limits so the gate reverses instead of pressing through whatever’s in its path. If the posts are heaving, we reset them first, because a new operator on a tilting post is money thrown away. Call (877) 610-2993 for a free assessment.
Gate Parts & Welding in Briar
Gate parts and welding in Briar means on-site repair of pipe-frame ranch gates, hinge brackets, catch posts, and slide tracks without hauling anything to a shop. We weld in your driveway because that’s where the gate lives, and because taking a 16-foot ranch gate off its posts just to fix a crack is the kind of shortcut that turns a half-day job into a two-day headache. Hal carries a mobile welding rig and keeps common steel sizes in stock for Briar’s standard 2-inch and 2.5-inch pipe frames.
On-Site Welding
We repair cracked gate frames, rebuild hinge brackets, and extend catch posts in the field. Most Briar gates are built from standard pipe that we can match on the truck, and we grind and paint the weld so it doesn’t rust out in two seasons. On-site welding for frame cracks or hinge rebuilds typically runs $185 to $390 depending on how much cutting and fitting is involved.
Parts Replacement
We stock hinges, rollers, chain, rack, and limit-switch parts for the nine major brands we service. For Briar’s older gates, that means we can often replace a worn hinge or a stretched chain on the first visit instead of ordering parts and making you wait. Parts-only calls run $130 to $280 for common hardware like hinges, rollers, or safety sensors.
Post and Frame Reinforcement
When a clay-heaved post has tilted far enough to stress the frame, welding the crack without fixing the post is temporary at best. We dig out the old footing, re-plumb the post, and weld reinforcement gussets to the frame so the gate can handle the next heave cycle. Post reset with new footing and frame reinforcement typically runs $210 to $480 per post.
Every Gate Parts & Welding job carries the 90-Day Done Right Promise. If a weld cracks or a hinge we replaced starts sagging, one call brings us back. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Can you weld my cracked gate frame without taking the gate off the posts?
Yes, in most cases we can weld a cracked frame in place using a mobile rig and proper shielding. We grind the crack, lay a strong bead, and add a reinforcement gusset if the frame is thin or the crack is in a high-stress area. The gate stays in your driveway, and you’re not paying for removal and re-hanging. Call (877) 610-2993 for an exact quote.
Do you stock parts for older Viking and FAAC operators common on Briar ranchettes?
We carry control boards, limit switches, and gear sets for most 1990s and 2000s Viking and FAAC operators, which are common on older Briar properties. If a part is discontinued, we’ll tell you plainly and quote a retrofit or replacement before we start. We don’t leave you guessing. Call (877) 610-2993 to check availability for your specific model.
Brands We Service in Briar
We are certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Briar’s older acreage gates, we most commonly see FAAC, BFT, Linear, and Viking operators, and we stock control boards and limit-switch parts for units dating back to the 1990s. Most brand-specific repairs are completed on the first visit. See our brands for full details on each manufacturer’s common failures and parts availability.
Pricing for Gate Repair in Briar, TX
| Service | Typical Range in Briar |
|---|---|
| Hinge repair and welding | $185 - $390 |
| Post reset with new footing | $210 - $480 per post |
| Operator limit re-tuning or safety sensor replacement | $130 - $280 |
| Control board replacement (legacy FAAC or Viking) | $240 - $520 |
| Electric gate operator repair (gear or motor) | $260 - $520 |
| Full operator replacement, swing gate with sensors | $620 - $1,150 |
| Gate realignment and frame reinforcement | $190 - $390 |
| Single swing gate installation, manual | $1,800 - $3,200 |
| Swing gate with operator, 12-16 ft | $3,800 - $6,500 |
| Sliding gate with operator, 16-20 ft | $5,500 - $9,000 |
| Solar operator add-on, battery + panel | $900 - $1,800 |
| Gate motor installation | $950 - $2,400 |
What pushes price up in Briar is usually the clay: posts set shallow heave and tilt, turning a simple hinge job into an excavation and re-pour. We quote every price before work starts, and that number doesn’t change at the door. We also take $40 off any repair over $200, and there’s no trip charge inside the county. Seniors and veterans get 10% off, permanently.
Neighborhoods We Serve in Briar
We work throughout the 76071 zip code and on the roads that define this unincorporated acreage community. Most properties sit on ranchette lots with long driveways, and we usually schedule an initial visit within the same week, often faster for emergency no-open calls.
- Properties along Briar Road and County Road 4685
- Acreage off County Road 4874 and in the Briar Creek bottom areas
- Ranchette lots along County Road 4785
- Long-driveway homes north toward Eagle Mountain Lake
- Caliche-track properties throughout the 76071 zip code
Service Area - Cities Near Briar
We serve Briar directly from our Dallas-Fort Worth office, with crews running locally throughout Wise County and the northern Tarrant County exurbs. If you’re near Briar, we also work in Briar, TX, Eagle Mountain, TX, Azle, TX, Saginaw, TX, Keller, TX, and Roanoke, TX. Call (877) 610-2993 and we’ll tell you straight if we cover your address.
Serving Briar, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Briar and the communities around it; dispatch is coordinated from our Dallas-Fort Worth office. The map shows the Briar coverage area; if your address is on it, we can help.
Also serving nearby: Briar, TX, Eagle Mountain, TX, Azle, TX, Saginaw, TX, Keller, TX, Roanoke, TX.
FAQs About Gate Repair in Briar
For emergency calls in the 76071 area, we can usually get a truck to your driveway the same day you call, often within a few hours. Non-emergency service is typically scheduled within one to two business days. Call (877) 610-2993 and Hal will give you a straight arrival window when he answers.
Unincorporated Wise County does not have the same municipal code enforcement you’d find in Fort Worth, but the safety obligations are real. Automatic gates must have entrapment protection, which means safety photocells or contact edges, and the operator’s force limits must be set correctly. UL 325 is the standard that governs gate operators, and we install to that standard on every job.
No. The price we quote is the price you pay, agreed in writing before any work begins. If we find something unexpected, we stop and discuss it with you before proceeding. No surprises at the door, no invoice bigger than the quote. That’s how we’ve operated since 2001, and it’s not changing now. Call (877) 610-2993 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Briar Customers Say
"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks