Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Bee Cave, TX
Gate repair in Bee Cave typically runs $180-$460 for most common fixes, with operator and motor work landing higher depending on brand and wiring condition. Most repairs in the 78738 ZIP are finished the same afternoon we hear from you, because a gate stuck open on a Hill Country lot isn’t something you set aside until next week. If your gate won’t open, sags at the latch, or grinds when it moves, call (877) 610-2993 and a live person picks up. Not a recording. Not a queue.
Why Bee Cave Homes Are Different
Bee Cave is one of the most gate-dense small cities in Central Texas - roughly 10,000 people packed with luxury master-planned communities where automated wrought-iron and steel estate gates are essentially standard. The bulk of these gates went in during the mid-2000s through 2010s building boom, which means they’re now hitting their first major operator-replacement and structural-overhaul cycle simultaneously.
The dominant housing stock is large custom and semi-custom homes built 2003-2018 on sizable lots with long private driveways. HOA covenants in Falconhead, Ladera, Lake Pointe, and Uplands at Bee Cave specify ornamental steel or wrought-iron with particular finishes and picket profiles. You can’t just bolt on any replacement part without checking whether the architectural review committee needs to sign off first.
Then there’s the ground itself. Bee Cave sits on expansive limestone and clay that swells with winter moisture and shrinks in August heat. Posts heave. Gates drift out of plumb. Latch alignment goes off by half an inch, and the operator starts fighting the frame every cycle. Barton Creek and its tributaries cut through the 78738 ZIP, so flash flooding after convective storms off the Edwards Plateau routinely shorts underground wiring and kills operators in low spots. These aren’t abstract problems. We see them every week.
Gate Repair in Bee Cave
Most gate repair calls we get from Bee Cave fall into a few categories: electric gates that won’t respond, automatic gates that groan and slow down, hinges that have worked loose from soil movement, and gates that drag because the geometry shifted underground. We start every diagnosis at the post, not the panel. Fix the panel without the post and you’ll fix it twice. Our crew carries parts for nine major brands on every truck, and we weld on-site so the gate stays in your driveway. Gate Repair is what we’ve built this business on since 2001.
Electric Gate Repair
An electric gate that won’t open, opens halfway, or reverses for no reason usually points to a power problem, a failed operator, or a photo-eye knocked out of alignment. The limestone and clay soils around Bee Cave shift with every wet-dry cycle, which can pull the frame just enough to misalign safety sensors. We trace the circuit, identify exactly what died, and replace the failed part, not the whole system. Most electric gate repairs in Bee Cave run $290-$650 depending on brand and failure type, and we quote the full price before starting.
Hinge and Post Repair
A gate sags in the hinge post, not in the middle, and that’s exactly where we start. The expansive clay under Bee Cave’s thin topsoil heaves and settles seasonally, putting torque on anchor posts and working hinges loose over time. Weld-on barrel hinges can tear away from the post face on heavy wrought-iron gates. We weld in place, strengthen or replace the post anchor, and realign the whole gate so weight distributes the way it did from the factory. Hinge replacement and realignment in Bee Cave typically runs $180-$390.
Gate Realignment
When a swing gate drags on its latch side or a slide gate shaves the track, the geometry is off. That’s a Bee Cave soil story most of the time. Post anchors shift subtly during dry spells and wet spells, and even an inch of movement at the post translates to a gate that won’t seat in its latch. We bring posts back to plumb, reset hinge geometry, and confirm the gate swings free and locks tight. Post repair with weld-up or reset runs $230-$550 depending on post size and excavation depth.
How fast can you get to Bee Cave for an emergency gate repair?
We’re usually on-site in Bee Cave within two to four hours for same-day service, including evenings and weekends. A live person answers the phone 24/7, so when your gate won’t open at 6 a.m. or you’re stuck outside at night, you’re talking to a person, not a voicemail queue. Call (877) 610-2993 and we’ll tell you straight whether it’s a quick fix or a bigger job.
Do you cover all Bee Cave HOA communities?
Yes. We work throughout the 78738 ZIP, including Falconhead, Falconhead West, Ladera, Uplands at Bee Cave, Lake Pointe, and custom-home streets off Hamilton Pool Road. HOA requirements are part of the job description here, and we keep architectural-review lead times in mind before any work begins. That local familiarity means fewer surprises and no fines after a legitimate repair.
Gate Installation in Bee Cave
Gate installation in Bee Cave runs $2,800-$9,500 for a standard automated driveway gate, depending on size, material, and whether you need slide or swing configuration. Most Bee Cave HOAs require architectural review approval before any gate goes in, and we handle that paperwork as part of the job. We’ve worked in the 78738 ZIP long enough to know which communities need what approvals and when. Gate Installation is scheduled and measured, not rushed - the price is agreed in writing before we order materials or dig a hole.
Driveway Gate Installation
Most Bee Cave homes sit on lots with long private driveways, so the main gate is the first thing visitors see and the last thing you want failing. We install slide and swing driveway gates in steel, wrought-iron, and aluminum, with operators sized to the gate’s weight and cycle frequency. A single swing driveway gate with a basic operator runs $2,800-$4,500. For double driveway gates in Uplands at Bee Cave, we check the slope first because even a two-degree grade change affects how the gate tracks.
Sliding Gate Installation
Sliding gates are common where driveways are level enough to support a track. The problem we see constantly is an installer setting the operator without a concrete pad under the rack and pinion. Hill Country clay swells with the first good rain, the pad shifts, and the pinion shears. We set a reinforced pad below the clay line on every slide gate we install in the 78738 ZIP. Slide gates run $6,000-$9,500 including the pad, rack, and operator.
Swing Gate Installation
Swing gates are our most frequent install in Bee Cave, and also the most common source of callbacks from other companies’ work. A swing gate that heaves out of alignment usually means the post footing wasn’t set deep enough or lacked a concrete collar. Our post footings go below the clay line, and we collar the post so it stays put through wet-dry cycles. A double swing gate with ornamental steel and a mid-range operator lands between $5,500-$8,000, depending on finish and hardware.
Do I need HOA approval before installing a gate in Ladera or Falconhead?
Yes, in most cases. Communities like Ladera, Falconhead, Falconhead West, and Lake Pointe require architectural review committee approval before a gate goes in, especially if it faces a public street. We pull the approval packet, submit photos and material specs, and coordinate the required inspection. Skipping that step can leave you with a gate you have to modify or remove at your own expense.
Why do swing gates in Bee Cave go out of alignment more than elsewhere?
Bee Cave sits on expansive limestone and clay that shifts dramatically with moisture cycles. That soil movement pushes gate posts out of plumb within a couple of seasons if the footing wasn’t over-excavated and set below the clay line. Flatter Austin suburbs on more stable soil don’t see the same heave. A crew that digs an 18-inch footing and calls it done will be back within 18 months.
Gate Motor & Opener in Bee Cave
When a gate motor fails in Bee Cave, it usually fails on a Monday morning with rain coming down and a car waiting in the driveway. Most operators here were installed during the 2003-2013 building boom and are now reaching end of service life. We repair when it’s honest and replace when it’s necessary, and we stock parts for nine major brands so you’re not waiting on a shipment. Gate Motor & Opener service is what keeps your gate moving.
Motor Repair
Most motor failures in Bee Cave aren’t the motor itself. They’re bad limit switches, corroded control-board connections, stripped gears, or a capacitor that’s been cooking in an unshaded Hill Country sun pocket for a decade. Repair beats replacement about seven times out of ten, and we’ll tell you when repair is the honest call. Typical motor repairs in Bee Cave run $180-$420, and when we’re done, you’ll know exactly what failed, why it failed, and what it’ll take to prevent it.
Motor Installation
Installing a new gate motor in Bee Cave often means dealing with a gate that’s been through fifteen Hill Country summers and several soil-movement cycles. We install operators that match the gate’s weight, usage frequency, and local conditions, not just whatever’s on sale. A typical motor installation runs $850-$1,450 depending on operator type and site work, and that price is quoted and agreed before we start. If your community requires architectural approval before a brand swap, we’ll build that into the timeline.
Linear Motor Service
Linear arm operators are common on the swing gates fronting Bee Cave driveways, from Ladera to Uplands. These motors push and pull a gate hanging on hinges set into soil that moves, which means the operator takes abuse from misalignment that started underground. We service and replace linear operators, check arm geometry, and address the underlying hinge-post issues so the new motor doesn’t burn itself out in six months. Linear motor repair or replacement typically falls between $260-$720.
How fast can you get to a gate motor repair in Bee Cave?
Most Bee Cave calls are handled same day, and emergency calls from 78738 get an immediate phone person who can often route a tech within a couple hours. We keep parts for brands common in Bee Cave and run service through the area multiple times each week. Call (877) 610-2993 and tell us what your gate is doing. We’ll tell you honestly what we can do and when.
Does the warranty hold up in Bee Cave?
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. That’s Hal’s guarantee, and it rides on the fact that the name is on the shop and the shop is down the road. One call brings him back, no runaround.
Gate Access Control in Bee Cave
Gate access control in Bee Cave means making sure your automated gate opens for the people you want and stays shut to everyone else. We repair, replace, and install keypads, remotes, phone entry, video intercoms, and card readers throughout the 78738 ZIP. If your keypad died during last week’s storm or your video intercom won’t ring through to your phone, call us and a live person answers. Gate Access Control is about reliability, not complexity.
Keypad Entry
A dead keypad is the most common access control call we get from Bee Cave homeowners. When a keypad fails, you either can’t get in without a remote, or worse, the gate won’t respond at all. Keypad failures peak right after heavy storms, because moisture gets into the housing and corrodes the board. We replace failed keypads, rewire the run back to the operator, and reprogram your codes on the spot. A typical keypad replacement runs $185-$320.
Remote Control
If one remote stops working, it’s usually the remote. If all of them stop at once, you have an operator receiver or antenna problem. We diagnose that distinction in minutes, and we stock remote transmitters for most major brands on our trucks. Remote programming, including testing all your existing clickers, typically runs $85-$150. We don’t sell you a new receiver because we don’t feel like chasing down an antenna problem.
Phone Entry Systems
Phone entry systems let you buzz visitors through from your cell phone, and they’re increasingly common in Bee Cave because many homeowners are here only part of the year. When a controller loses its cellular connection or its relay sticks, the gate either won’t ring through or won’t open when you answer. We service the controller board, the relay, and the wiring back to the operator. Phone entry repair generally runs $220-$450.
How do we manually open our gate when the power goes out during a storm?
Locate the manual release handle on your operator, usually a red or yellow pull lever near the motor. Pull it to disengage the gearbox, then push the gate open by hand. If the gate has shifted out of plumb from clay movement, it may be heavy, so push slowly. If you can’t find the release or the gate won’t move, call (877) 610-2993.
Can you replace a gate operator with a different brand in Falconhead?
Sometimes yes, sometimes no. Many Bee Cave HOAs specify operator brands and finish standards in their covenants. If the community requires a particular brand, we install that brand. If the existing operator is grandfathered and you want to switch, we’ll pull HOA approval first and tell you how long it adds. We keep HOA contact sheets for the communities we serve.
Gate Parts & Welding in Bee Cave
When a hinge tears loose or a weld cracks on an estate gate in Bee Cave, you don’t have time to wait three days for a crew that may or may not show. Gate parts and welding should be a same-day conversation, with a live person on the phone and someone who knows where Falconhead is without typing it into a GPS. We weld on-site with a mobile rig, which keeps the gate’s existing hinge geometry intact. Gate Parts & Welding is repair-first work, not replacement-by-default.
Hinge Replacement
Bee Cave’s estate gates are heavy. Wrought-iron and ornamental steel panels put constant load on hinge pins and weld points, and when a hinge starts to groan or sag, the gate is telling you something. We remove and replace hinges with the gate still hung, keeping alignment true. In Falconhead and Ladera, we regularly see hinge barrels that were under-sized from the original install and have wallowed out over a decade of Hill Country wind. Hinge replacement typically runs $180-$340 per hinge.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. Bee Cave’s limestone and clay soils heave and settle with every wet-dry cycle, and the post that was plumb in 2008 might be two inches out of true by spring. We pull the old post, set a new one in properly compacted concrete, and weld the hinge brackets back in the correct plane. Post replacement usually lands between $480-$900 depending on post size and access.
Rail Repair and Custom Welding
Bottom rails collect moisture, then rust, then split at the welds. On Bee Cave’s long private driveways, we see bottom-rail failures where irrigation overspray keeps the lower steel damp for years. We cut out the bad section, weld in new material, and dress the joint so the repair disappears under the finish. On HOA-governed properties, we match the original profile and picket spacing. Most residential rail repair and custom welding falls between $200-$650.
How fast can you get to Bee Cave for a welding job?
In most cases, we can have someone at your Bee Cave property same day, often within a few hours. Our trucks are in the area throughout the week, and because we weld on-site with a mobile rig, the person who arrives is the person who starts the repair immediately. For emergency work like a gate blocking your driveway, call (877) 610-2993.
Is gate welding more expensive in Bee Cave than in Austin?
Labor rates are essentially the same across Travis County, typically within $20-$40. The bigger variables in Bee Cave are drive time on remote lots, HOA-required finish matching, and the heavier gate construction common in master-planned communities. Our pricing is the same no matter where we’re working, and there’s no trip charge inside the county.
Brands We Service in Bee Cave
We stock parts and carry factory authorization for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Linear and DoorKing show up constantly in Bee Cave’s 2000s-era builds, and we keep common control boards, gear sets, and safety sensors on the truck. Most brand-specific repairs don’t require a return visit. our brands
Pricing for Gate Repair in Bee Cave, TX
| Service | Typical range in Bee Cave |
|---|---|
| Hinge replacement and realignment | $180-$390 |
| Electric gate operator repair | $290-$650 |
| Post repair (weld-up or reset) | $230-$550 |
| Automatic gate sensor or limit-switch replacement | $150-$320 |
| Weld and rust repair on ornamental steel | $200-$480 |
| Single swing driveway gate installation | $2,800-$4,500 |
| Double swing gate with ornamental steel | $5,500-$8,000 |
| Slide gate installation (with pad, rack, operator) | $6,000-$9,500 |
| Motor repair | $180-$420 |
| Motor replacement with installation | $850-$1,450 |
| Keypad entry repair or replacement | $185-$320 |
| Phone entry repair | $220-$450 |
Several things move the number within these ranges: gate weight and width, whether post anchors need drilling and re-setting, and whether HOA approval is required before materials go in. The price you’re quoted is the price on the invoice, period. We don’t do adjustments at the door. Estimates are free, there’s no trip charge inside Travis County, and every job carries the 90-Day Done Right Promise in writing.
Neighborhoods We Serve in Bee Cave
We cover all of Bee Cave’s 78738 ZIP, with same-day or next-morning response for repairs depending on when you call. These are the neighborhoods we get called to most often:
- Falconhead
- Falconhead West
- Ladera
- Uplands at Bee Cave
- Lake Pointe
If you’re in one of these neighborhoods and your gate is acting up, call (877) 610-2993. We’ll tell you straight whether it’s a quick fix or a bigger job before we ever set foot in the truck.
Service Area - Cities Near Bee Cave
We run gate repair and installation throughout the Hill Country west of Austin. Our crew serves Bee Cave, TX locally, with scheduling coordinated from our Austin office. We also work regularly in Lakeway, TX, Lago Vista, TX, Shady Hollow, TX, Austin, TX, and Leander, TX. If you’re unsure whether we cover your property, call and ask. A live person answers.
Serving Bee Cave, TX - Our Local Coverage Area
Gatewood Fence & Gate crews serve Bee Cave and the communities around it; dispatch is coordinated from our Austin office. The map shows the Bee Cave coverage area; if your address is on it, we can help.
Also serving nearby: Bee Cave, TX, Lakeway, TX, Lago Vista, TX, Shady Hollow, TX, Austin, TX, Leander, TX.
FAQs About Gate Repair in Bee Cave
Usually not for straightforward repairs that don’t change materials, finish, or operator brand. But in Falconhead, Ladera, and Lake Pointe, swapping an operator brand or altering the gate color can trigger architectural review. We check HOA requirements before work begins so you don’t face fines after a legitimate repair.
After heavy storms off the Edwards Plateau, we see flooded operators, shorted underground wiring, and loop detectors that fail without warning. Don’t power-cycle a wet operator - it can make things worse. Call (877) 610-2993 and we’ll assess what’s salvageable, what needs replacement, and what your insurance company will want documented.
Most gate repairs in Bee Cave are completed same day. We stock common parts for all nine major brands, which avoids the return visits other shops schedule because they didn’t carry the right part. Major structural post excavation on a long set-back custom lot might need a second visit, but we’ll tell you that upfront.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bee Cave Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg