Gate Parts & Welding in Everett - Made to Measure, Written Price

Fast, Reliable Gate Parts & Welding Across Everett

Gate Installation - Everett hinge replacement usually runs $275-$450 per hinge set, and welding repair on an old wrought-iron gate typically costs $180-$380 on site. That’s the number most homeowners want when they call us about a sagging side-yard gate that won’t close or a rusted-through bottom rail on a 1920s triple-decker. We’re Gatewood Fence & Gate, and Hal Gatewood has been welding and repairing gates himself since 2001, not reading from a script in a faraway office. When your gate binds at the hinge post on a 19-inch passage just off Broadway, that is work we do in a driveway, with the gate still on its posts most of the time.

Call (877) 610-2993

Call (877) 610-2993. A live person answers no matter the hour, and we’ll talk you through exactly what the Everett site looks like, what has failed, and what it takes to fix it before you ever see a bill.

Why Gatewood Fence & Gate Is Everett’s Preferred Gate Parts & Welding Company

Hal’s name is on every invoice and the shop is down the road. That is the oldest form of accountability there is. We do not route calls through a call center, and we do not send a faceless crew to quote one thing and bill another. The person who answers the phone in the middle of the night is the same person who will stand in your alley and tell you honestly whether the hinge needs grease or the post needs to come out.

Everett’s gate problems are not like Malden’s. Here, the side yards are alley-width, the iron is a century old, and the salt air off the Mystic River and Chelsea Creek gets into every weld and hinge pin. That local knowledge changes how we diagnose a stuck gate before we ever unbolt a single lag screw, which is why Gate Access Control in Everett starts with the right diagnosis. Our Everett customers call back for one reason: we fix what is failing and we leave what is still working alone. And the 90-Day Done Right Promise is stamped in writing on every job, not buried in fine print.

We do not offer call-center service because we are not a call center. We schedule Everett work around the drive, not the other way around, and on repair calls the person who shows up can tell you what the salt air has already told us about your gate’s hardware.

Our Gate Parts & Welding Services in Everett

Most of what we do on Everett lots is repair-first work: replacing one hinge, one post, one rail, or welding a crack before it becomes a full gate replacement. Here is what that looks like in 02149.

Hinge Replacement

Old wrought-iron side-yard gates in Everett often hang on original hinges that have seized solid from decades of salt-air corrosion off Chelsea Creek. When the passage is only 18 to 24 inches between house and fence, we cannot just swap hardware blindly: we have to cut or break the old hinge free, confirm the post still holds, and weld or bolt a hinge set that lets the gate swing open the full arc without banging the siding. A hinge replacement in Everett typically runs $275-$450 per set, and we quote it before anything gets cut.

Post Replacement

New England’s freeze-thaw cycles heave concrete-set gate posts out of plumb all over the Boston area, but in Everett it happens faster because the soil near the Mystic River holds moisture and the posts are often set shallow on narrow parcels. A post that has shifted even two degrees will bind a slide gate’s rack and pinion or keep a swing gate from latching. We cut and weld new steel posts with deeper footings, then re-hang the gate so it operates like the day it went in. Post replacement in Everett runs $350-$800 depending on footing depth, access, and whether the old concrete must be hammered out by hand.

Rail Repair

Bottom rails on old iron gates rust through first because water pools there after every storm off the river. We weld new rail sections rather than replacing the whole gate: we cut back to sound metal, weld in matching steel, and grind the joint smooth. If the rust has attacked the top rail too, we’ll tell you straight before you spend money. Rail repair runs $180-$380 for a typical three-foot section on a side-yard gate in Everett.

Custom Welding

Tight Everett lots often need something a catalog does not sell: a gate re-hung on offset hinges to clear a narrow passage, a slide conversion where a swing gate will not fit, a custom latch plate welded to match 1920s iron. We weld on site in the driveway, so the gate never leaves your property. Custom welding rates run $95-$140 an hour, and most single-job custom fixes land between $250 and $600. You get a written price before the first bead is laid.

See the full breakdown on our Gate Parts & Welding page, or call (877) 610-2993 and describe what your gate is doing. Hal will tell you whether it is a weld fix or a hinge replacement and what it should cost.

Trusted Brands We Service in Everett

We stock parts locally for the Everett Gate Motor & Opener systems homeowners actually use: Linear, Viking, and Ghost Controls are the three we see most on side-yard and rear-alley gates in 02149. If you need a slide kit for an alley conversion or a direct replacement board for an older Linear operator, we can usually bring it with us instead of waiting two weeks for a distributor. We are not married to one manufacturer: we service what works, not what pads a margin.

Common Gate Parts & Welding Problems We See in Everett Homes

Everett’s housing stock and riverfront weather create a specific set of gate failures. These are the four we see most often when we answer the phone.

• Seized iron hinges on 18-24 inch side-yard passages. The original wrought-iron hinges on many pre-1930 gates have rusted solid from salt air off Chelsea Creek. The gate will not swing at all, and the fix usually means cutting the hinge pin or the hinge itself, then welding a new set in place.
• Heaved concrete-set posts on shared driveways. Freeze-thaw cycles along the Mystic River push posts out of plumb, misaligning a slide gate’s rack and pinion. The gate jams halfway along the track, and the fix is a new post with a deeper footing, not a track adjustment.
• Shared fence line gates that have gone unrepaired for years. On many triple-decker blocks off Broadway, a single gate straddles two properties. Neither owner takes responsibility until the hinge post snaps. By the time we arrive, the gate is hanging at a forty-five-degree angle and both households are calling for help.
• Rusted-through bottom rails. The lowest rail on an iron gate rots first because rainwater and river mist sit there. We weld a new rail section and keep the rest of the original gate, which preserves the look and saves real money.

For Everett homeowners, these are identity problems: the gate is not a rental ornament. It is access control for a narrow lot, and when it fails, trash gets out, deliveries back up, and a neighbor’s dog makes a break for Broadway.

Pricing for Gate Parts & Welding in Everett, MA

We Also Serve Cities Near Everett

We work throughout close-in Middlesex and Suffolk, including Malden, Chelsea, Revere, and Medford. Each has its own quirks: Revere’s seaside exposure, Malden’s wider suburban lots, Chelsea’s industrial-era ironwork. For Everett specifically, the shared fence lines and salt-air corrosion are the through-line, and that is how we build every local job. Read more about our local service area on our Gate Parts & Welding in Everett page.

FAQs - Gate Parts & Welding in Everett