Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Brentwood
Gate parts and welding in Brentwood usually means one of two calls: a hinge that finally let go, or an operator from the early 2000s that quit. Most jobs run $250-$700 and we handle them same week, often same day. Hal Gatewood has been fixing gates since 2001, and the person who answers the phone at (877) 610-2993 is the same person who will show up at your driveway. If you’re in the 94513 and your gate is binding, sagging, or stuck open, call us before it gets worse.
Why Gatewood Fence & Gate Is Brentwood’s Preferred Gate Parts & Welding Company
Hal’s name is on the shop and on every invoice. That matters in a city like Brentwood, where a lot of homeowners got burned by big outfits that quoted one price on the phone and handed over a different number at the door. We don’t work that way. The price is quoted and agreed before any work starts, in writing. No surprises, no fine print, no “well, it turned out to be more involved.”
Brentwood is our backyard. We know the tract layouts along Balfour Road, the monument entries off Sand Creek Road, and the large-lot homes built between 1998 and 2008 that all share the same gate hardware. That consistency means we often know what’s wrong before we arrive, and we carry the common parts on the truck. Hal’s crew is background-checked and uniformed, and we never send a subcontracted stranger. The person you meet is the person Hal trained.
Every job carries the 90-Day Done Right Promise, stamped in writing. If something isn’t right, one call brings us back. No runaround, no argument. That promise has been the backbone of our Brentwood reputation for years.
Our Gate Parts & Welding Services in Brentwood
Our Gate Parts & Welding crew handles the structural side of gate repair: the steel, the hinges, the posts, the welds. Here’s what we do most in Brentwood.
Hinge Replacement
Delta winds funneled through the Altamont corridor beat on Brentwood gates year-round. Those constant lateral loads wallow out hinge pin holes within 5-8 years on most ornamental iron gates, especially on larger HOA monument entries. We cut out the old hinge, weld in a heavier barrel hinge with greasable pins, and realign the gate so it doesn’t hang stress on the operator. A typical hinge replacement in Brentwood runs $180-$400 per hinge depending on gate weight and access.
Post Replacement
When a hinge post leans, the gate follows. Brentwood’s delta soils hold moisture, and rotted post footings are common under gates built during the 2000s boom. We dig out the old footing, set a new steel post in concrete, and rehang the gate square. A post replacement with new anchors and rehanging typically runs $500-$1,200 in Brentwood, depending on whether it’s a driveway swing gate or a heavier community entry. This is not a job to delay: a leaning post accelerates hinge wear and eventually binds the gate entirely.
Rail Repair
Summer heat in Brentwood regularly hits 100°F+, and steel gate frames expand enough to bind against latch strikes and ground hardware. Over time, top rails bend and pickets twist. We straighten what’s salvageable and weld reinforcement where the steel has fatigued. If the rail is beyond repair, we fabricate a new section on site rather than replacing the whole gate. Rail repair and straightening usually runs $250-$600 in Brentwood.
Custom Welding
Some Brentwood gates weren’t built for Brentwood’s wind. We weld on site, which means your gate stays in your driveway. We reinforce weak points, add gussets to stress corners, rebuild rusted-through sections, and fabricate brackets or mounting plates for operators and locks. Custom welding rates in Brentwood run $120-$180 per hour, and Hal caps the quote before the torch lights. There’s no hauling your gate to a shop and waiting three weeks.
Beyond these, we also replace gate rollers on slide gates, rebuild latch and lock hardware, and weld up sagging frames. If it’s steel and it’s on a gate, we can probably fix it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Brentwood
Most Brentwood tract homes from the 2000s came with Viking or Linear operators, and we service both. We also work on FAAC and BFT units that are common on newer custom installations. Hal is certified across nine major gate brands, and we stock the common parts locally so Brentwood customers aren’t waiting on a warehouse three states away. If your operator is still sound but a hinge or post failed, we’ll weld the gate back to proper alignment rather than sell you a new motor you don’t need.
Common Gate Parts & Welding Problems We See in Brentwood Homes
- Hinge pins wallowed out from Delta winds. The persistent afternoon breeze through the Altamont corridor pushes on gate frames constantly. After 5-8 years, hinge holes elongate and the gate drops enough to drag or bind.
- Obsolete Viking and Linear loop detectors shorting on delta soil moisture. Balfour Road and Sand Creek Road neighborhoods sit on agricultural soils that hold water just below the surface. Buried loop wire corrodes and misfires, leaving gates stuck open or triggering randomly.
- Thermal binding in summer heat. A steel gate that swings fine in March can bind hard in July. The frame expands, and if the hinges or post are even slightly off, the gate presses into the latch strike or ground hardware. We replace the hinge, realign the post, or weld in clearance as needed.
- Top rails bent from wind load on wide double gates. Double driveway gates catch wind like a sail. We see bent top rails and twisted pickets most often on homes with large side yards along open corridors. Welding reinforcement plates and straightening the rail usually solves it without replacing the gate.
Pricing for Gate Parts & Welding in Brentwood, CA
What you’ll pay in Brentwood comes down to gate size, steel condition, and how far the misalignment has progressed. A hinge replacement runs $180-$400 per hinge. Post replacement runs $500-$1,200. Rail repair and straightening runs $250-$600. Custom welding runs $120-$180 per hour, with the quote capped before work begins.
| Service | Typical Brentwood Price |
|---|---|
| Hinge replacement (per hinge) | $180-$400 |
| Post replacement (with rehang) | $500-$1,200 |
| Rail repair / straightening | $250-$600 |
| Custom welding (per hour) | $120-$180 |
| Gate roller replacement | $150-$350 |
| Latch & lock rebuild | $120-$280 |
Every quote is written and agreed before we start. You’ll also get $40 off any repair over $200, and there’s no trip charge anywhere inside the county. Seniors and veterans get a permanent 10% discount. For an exact number on your gate, call (877) 610-2993 and Hal will talk you through it.
We Also Serve Cities Near Brentwood
We regularly work in Oakley, Discovery Bay, Antioch, and Clayton, where the same Delta winds and delta soils age gates the same way they do in Brentwood. If you’re in 94513 or just outside it, we’re close. Dispatch and scheduling are coordinated from our San Francisco Bay Area office, and crews serve Brentwood locally, so we’re in your neighborhood most days of the week.
Serving Brentwood, CA - Our Local Coverage Area
We’re based in the Brentwood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Brentwood
Brentwood’s master-planned neighborhoods along Balfour Road and Sand Creek Road sit on former agricultural delta soils that hold moisture just below the surface. Buried loop detector wire in those wet soils corrodes much faster than it would in drier Bay Area cities just 30 miles west. When the loop shorts, gates either stay open or trigger at random. We replace the loop wire and, where possible, upgrade the detector to a model rated for high-moisture soil. Call (877) 610-2993 and we’ll diagnose it on site.
Honest answer: it depends on what failed. A 2004-era Viking or Linear operator that’s still running but overheating is often fighting a misaligned gate, and fixing the hinge or post relieves the load and extends the motor’s life. If the control board is dead and parts are obsolete, replacing the operator is usually the cheaper long-term answer. We’ll show you the math on both options before you spend a dollar. Call (877) 610-2993 for a straight assessment.
It’s common, but it’s not normal. Brentwood regularly hits 100°F+ in summer, and steel gate frames expand enough to bind against latch strikes and ground hardware. If the hinges or post are even slightly worn or shifted, the expansion turns a small misalignment into a hard bind. We weld hinges with more clearance, realign the post, or reinforce the frame so summer heat doesn’t lock your gate shut. Estimates are free.
In most cases, welding fixes it. We straighten the rail, weld in reinforcement, and add gussets at the stress points so the same wind doesn’t re-bend it in two years. We only recommend replacement when the steel has rusted through in multiple places or the frame is so fatigued that welding would be chasing one failure after another. We’ll show you the gate and explain what we’d do before any torch lights up.
Usually it’s both. The operator isn’t causing the problem, it’s reacting to it. When a Brentwood gate binds in the heat, the motor has to work harder every cycle until it trips its thermal overload. The fix is often a hinge replacement or post realignment, not a new operator. We’ll check the gate’s free movement, measure the amperage draw, and tell you what’s actually failing before recommending parts. Call (877) 610-2993 for an exact quote, estimates are free.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Brentwood since 2001.