Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Aurora
Gate parts and welding in Aurora, OH usually means one of three things: a hinge post that’s pulled loose in a thaw, a bottom rail rusted through from road salt, or a 1990s underground operator that’s finally given up. Most Gate Installation in Aurora jobs we see in subdivisions run between $180 and $1,400 depending on whether we’re welding a cracked joint or setting a new post and retrofitting the operator. We’ve been fixing gates in northeast Ohio since 2001, so when you call (877) 610-2993, you’ll get a real person who knows the difference between a Walden Trail install and a Barrington Estates one – and a crew that shows up when we say we will.
This is owner-operated work. Hal Gatewood’s name is on the shop and on every invoice, and the person who answers your call is the same person who stands behind the Gate Parts & Welding work we do. No dispatch queue, no outsourced call center, no tech you’ll never see again.
Why Gatewood Fence & Gate Is Aurora’s Preferred Gate Parts & Welding Company
Aurora homeowners have a particular problem most other towns don’t: a lot of very nice gates installed twenty to forty years ago that are all hitting their failure window at the same time. The subdivisions along Route 43 and around the Barrington and Walden communities were built out fast in the 1990s and early 2000s, and the gate hardware that went in then wasn’t always up to what northeast Ohio winters demand. We see the same patterns again and again – post footings that heave, weld junctions that crack, underground actuator vaults that flood – and we’ve learned exactly where to start.
Our local reputation in Aurora is built on showing up and doing the repair in your driveway instead of hauling the gate to a shop or, worse, pitching you a full replacement before we’ve even looked. The 90-Day Done Right Promise is stamped in writing on every job. If something isn’t right, one call brings Hal back. That’s not a marketing line; it’s the way we’ve kept customers in 44202 coming back since the beginning. Background-checked, uniformed crew, licensed and insured, with a published address you can drive to and a face you’ll see again at the hardware store.
Our Gate Parts & Welding Services in Aurora
Hinge Replacement
A sagging gate in an Aurora subdivision usually isn’t a gate problem at all – it’s a hinge post problem. The post moves, the hinge binds, and the panel starts dragging. We cut out the old hinge hardware, reset or replace the post, and re-weld the hinge mounts at the correct height so the gate swings clean. In the Barrington Estates subdivision, we replaced a hinge post on a builder-grade swing gate that had pulled 3 inches out of its concrete footing after a thaw cycle. Our tech cut out the old post, set a new footing, and re-welded the gate to the operator arm, then added a safety photocell because the original install skipped entrapment protection. In Aurora, hinge replacement on a standard ornamental gate typically runs $260 to $520.
Post Replacement
Post replacement is the most common structural repair we do in Aurora’s 1980s-2000s subdivisions. Freeze-thaw cycling heaves posts set in concrete, especially when the original footing was undersized or the post wasn’t sleeved. A post that’s moved even half an inch changes the gate’s geometry, so the latch stops engaging and the operator starts working against itself. We dig out the old footing, set a new post to full depth below the frost line, and weld the gate back square. In Aurora, a standard post replacement with new footing runs $400 to $800, more if the operator arm or electrical conduit has to be moved.
Rail Repair
Wrought iron and ornamental tubular steel gates in Aurora rust through at the bottom rail first. Decades of road salt blown in from plowed subdivision streets sits on that lower rail all winter, and once water gets inside the tubing it’s only a matter of time. Rail repair means cutting out the rotted section, welding in a new piece of matching steel, grinding the joints smooth, and priming and painting so the repair disappears. Typical rail repair in Aurora runs $180 to $400 per rail section depending on length and access.
Custom Welding
Not every gate repair is a straight swap. When a bracket shears, a decorative finial snaps, or a homeowner wants to widen a gate opening without replacing the whole panel, custom welding in the driveway is the answer. We weld on site, in Aurora, so your gate never leaves your property. Custom welding work in Aurora’s subdivisions typically runs $150 to $600 depending on how much fabrication is involved. That’s materials, labor, and cleanup – quoted and agreed before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Aurora
We’re certified to service nine major gate brands, and we stock Aurora Gate Motor & Opener parts locally for the ones older subdivisions actually use. If your 1990s-era entrance gate runs on a Linear or FAAC underground actuator, we know those systems and we know which parts are worth chasing and which aren’t. We also service DoorKing, Elite, and Ghost Controls operators, so whether your gate was put in twenty years ago or last summer, we have the parts and the knowledge to keep it running. Parts for older Linear and FAAC systems are getting scarce everywhere – in Aurora especially, we’re often quoting full operator replacements rather than repairs because the original units are simply obsolete.
Common Gate Parts & Welding Problems We See in Aurora Homes
- Builder-grade operators failing within 5 to 8 years. Aurora’s snow-belt duty cycle is hard on equipment. The original operators installed in many 2000s subdivisions were undersized for the gates they run, and the conduit runs were often too small to support modern automation. We frequently replace these with properly sized units matched to the gate’s weight and wind load.
- Manual gates that were never pre-wired for automation. Most of the manual gates in Aurora’s 2000s subdivisions went in with no power and no control conduit. Adding a keypad entry or a loop detector means trenching new power and control conduits from the house or panel. That’s an extra step a lot of national outfits won’t even quote; we do it regularly and we’ll show you exactly what’s involved.
- Bottom rail rust-through from road salt. Aurora’s plowed subdivision streets put salt right at the base of every gate. Once the powder coating chips or scratches, corrosion starts and spreads inside the tube. By the time you see a rust bubble, the section underneath is often already thin.
- Heaved post footings after spring thaw. Frost depth in Portage County means post footings need to go deep. When they don’t, the first hard thaw moves them. A gate that was square in October is dragging by March, and that’s when we get the calls.
Pricing for Gate Parts & Welding in Aurora, OH
We quote every job before we start, and you’ll know the number before any work begins. Hinge replacement in Aurora typically runs $260 to $520. Post replacement runs $400 to $800 depending on footing depth and whether we’re moving electrical. Rail repair is $180 to $400 per section. Custom welding is $150 to $600 depending on fabrication time. These are real ranges for Aurora’s market, not national averages. $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Estimates are free. If you have a written estimate from another company, bring it in for a second opinion – also free. Call (877) 610-2993 for an exact quote.
We Also Serve Cities Near Aurora
While most of our gate repair and welding work is in Aurora proper, we routinely handle gates in Streetsboro, Twinsburg, Solon, and Macedonia. If you’re in a neighboring community and need Gate Parts & Welding work done, call us – the same owner-operated service applies.
Serving Aurora, OH - Our Local Coverage Area
We’re based in the Aurora area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Aurora
Those early-generation FAAC and Linear underground actuators were never designed for the freeze-thaw heaving we get in Aurora’s snow belt. Water seeps into the vault, freezes, expands, and eventually cracks the housing or seizes the motor. After a hard winter that heaves the vault, the repair is usually a full operator replacement rather than a parts fix – most of those original components are obsolete and no longer manufactured. Call (877) 610-2993 and we’ll tell you what a replacement for your specific gate will cost, free of charge.
Yes, almost always. Most manual gates in Aurora’s 2000s subdivisions were never pre-wired for automation. Adding Gate Access Control - Aurora like a keypad entry or loop detector means trenching new power and control conduits from the house or panel to the gate location. We handle the full trenching, wiring, and operator installation – you don’t need to bring in a separate electrical contractor. For an exact quote in Aurora, call (877) 610-2993.
In most cases, yes. A gate sags in the hinge post, not in the middle. When the post heaves or the footing settles, the whole gate shifts and drags. Fix the panel without fixing the post and you’ll fix it twice. We diagnose the post first, because that’s where Aurora’s freeze-thaw cycles hit hardest. Call (877) 610-2993 for a free assessment.
Yes. Under current safety standards, any automated gate operator requires entrapment protection – typically photocells and contact edges – regardless of whether the gate itself is new. Many of the older Aurora installations skipped this, and we add it as part of every operator replacement. It’s not optional equipment; it’s what keeps kids and pets safe around a moving gate. We’ll include it in your quote, clearly labeled, before any work begins.
That’s road salt. Aurora’s plowed subdivision streets push salt-laced snow right against the base of every gate along the curb line. It sits on the bottom rail all winter, chips the powder coating, and starts corrosion from the outside in. Once water gets inside the tube, it rusts from the inside out too. Cutting out the rotted section and welding in new steel is the only permanent fix. Call (877) 610-2993 and we’ll come look at it.
Contact Gatewood Fence & Gate in Aurora, OH
If your gate needs hinge replacement, post replacement, rail repair, custom welding, or a full operator retrofit, call (877) 610-2993. A live person answers around the clock. We’ll schedule a time that works for you, show up in the window we promised, and quote every dollar before any work starts. The name is on the shop, and the shop is down the road – that’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Aurora since 2001.