Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Uhrichsville, OH
Gate repair in Uhrichsville typically costs between $180 and $600 depending on whether we’re rebuilding a heaved post, replacing a control board, or welding a cracked hinge. Most jobs can be scheduled within a day or two, and a real person answers the phone any time you call. We know Uhrichsville’s gates the way you know its streets: older, hardworking, and built for daily use. Call (877) 610-2993 and Hal Gatewood or one of his crew will have you sorted.
Why Uhrichsville Homes Are Different
Uhrichsville sits on the same clay-rich geology that earned it the nickname Clay City and powered its historic tile and brick industry. That expansive clay is the dominant gate-repair challenge in this town. The soil swells with moisture, freezes through the winter, and heaves, which means gate posts tilt and shift seasonally. A gate that latched fine in September may bind and drag every March.
Most of the residential properties here date from the early to mid-20th century, built during the clay and pottery boom. That means fences and gates are often decades old, with corroded steel hardware, rotted wooden posts, or original chain link that has never been touched since it went in. Many lots are modest working-class properties with side and rear gates that see heavy daily use. A local technician quickly learns that simply re-hanging a sagging gate in Uhrichsville without addressing the heaved post is a waste of a service call. The clay will move it again within one freeze cycle. The real job almost always starts at the base of the post.
Eastern Ohio delivers frequent freeze-thaw cycles through November to March, and Tuscarawas County’s clay-heavy subsoil amplifies frost heave significantly compared to sandier or rockier neighboring counties. Gate posts that are not set below the 32-inch frost line will shift almost every season, making proper footing depth a recurring repair conversation with local homeowners.
Gate Repair in Uhrichsville
Gate repair in Uhrichsville usually costs between $180 and $600 depending on whether we’re rebuilding a heaved post, replacing a control board, or welding a cracked hinge. Most jobs can be scheduled within a day or two, and a real person answers the phone any time you call. We know Uhrichsville’s gates the way you know its streets: older, hardworking, and built for daily use. Gate Repair is what we built this company on, and it’s still the bulk of what we do in Tuscarawas County.
Hinge and Post Repair
This is the big one around here. Your gate post sits in clay that swells when it rains and heaves when it freezes. If that post wasn’t set on a proper concrete collar below the 32-inch frost line, it shifts. A shifted post throws the hinge alignment off, the gate sags, and suddenly you’re dragging a 200-pound gate across the driveway just to get the mower out. We dig it up, correct the footing, and set it right. A typical hinge and post repair runs $220-$450 depending on depth of the new footing and concrete needed. In Uhrichsville, this is usually the first and only repair a gate actually needs.
Electric Gate Repair
Electric gates in Uhrichsville are often older units with control boards that have been through a decade or two of freeze-thaw cycles. We see boards that fire the motor but won’t stop it, boards that lock out after a power blip, and limit switches that have lost their minds. We repair what can be safely repaired, and we’ll tell you plainly when a board is dead and replacement is the cheaper answer than chasing parts on an obsolete model. Electric gate repairs start around $180 for limit switch or safety edge work, and go up to $400-$600 for a replacement control board on an older operator.
Gate Realignment
A gate that scrapes or won’t latch is usually a symptom of something below grade. We realign after correcting whatever moved. On older chain-link gates, that often means new hinge hardware, a reset post, and a gate that swings like it did when it was new. If the panel itself is bent, we straighten it in place where possible. Gate realignment on a chain-link driveway gate is usually $150-$300 once the post is sound. Fix the panel without the post and you’ll fix it twice.
Why does my gate bind every spring in Uhrichsville even after I adjust the hinges?
Because the post underneath the hinge is moving, not the gate itself. Uhrichsville’s clay soil swells with spring moisture and pushes shallow-set posts upward, shifting the hinge alignment you just adjusted. Adjusting hinges without correcting the post footing chases the same problem every year. The fix is resetting the post on a concrete collar below the 32-inch frost line. Call (877) 610-2993 and we’ll tell you what your specific post needs.
How deep should a gate post be set in Uhrichsville to stop seasonal movement?
At least 32 inches deep, with a concrete collar that extends below the frost line and anchors the post against the expansive clay. That’s the depth we use on every post reset in Uhrichsville because shallower footings heave within a winter or two. It’s the single most important variable in a gate repair that actually lasts here.
Gate Installation in Uhrichsville
Gate installation in Uhrichsville typically runs $900-$3,400 depending on whether we’re setting a single pedestrian gate or a double driveway gate with an operator, and most jobs go from first measure to finished install within 7-14 days. We’re not a franchise crew passing through. The person who measures your gate is the same person who welds it, sets the posts, and stands behind it for 90 days in writing. Gate Installation in clay soil means doing the underground work right the first time, or you’re back in two years.
Driveway Gate Installation
A driveway gate in Uhrichsville has to take daily abuse from freeze-thaw cycles, clay soil movement, and whatever the county road crew throws at it in winter. We set steel posts below the 32-inch frost line, weld hinge points on site, and install operators from brands like FAAC and BFT that handle the freeze without draining the board. A single swing driveway gate with a FAAC or BFT operator runs $2,200-$3,400. The goal is a gate that opens in February without you getting out of the truck.
Pedestrian Gate Installation
Side and rear pedestrian gates in Uhrichsville see more use than any other gate on the property, and they’re usually the ones built cheapest. We build pedestrian gates with pressure-treated or steel posts, concrete collars engineered for clay, and hinges that won’t bind when the ground moves. A new pedestrian gate in Uhrichsville typically runs $900-$1,800 including posts, hinges, and hardware. If your walk gate gets slammed 20 times a day by kids and dogs, that’s exactly what we build for.
Sliding Gate Installation
When the driveway is tight or the grade runs toward the street, a sliding gate is often the right call for Uhrichsville lots. We set the track on a deep base so frost doesn’t kick it out of alignment, hang the gate level, and dial in the operator’s force settings. A double gate with a heavy operator and full safety system runs $3,200-$5,200 depending on span, materials, and whether we’re retrofitting old posts or setting new ones below the frost line. A sliding gate that fights the track is a sliding gate that eats motors. We don’t build those.
Why does my newly installed gate in Uhrichsville sag every spring even though the hinges are tight?
The post is moving, not the hinges. Uhrichsville sits on the same clay-rich geology that powered its historic tile and brick industry, and that clay swells with spring moisture and freezes in winter. If the post was set less than 32 inches deep, the ground itself lifts it, and the gate sags. The fix means excavating below the frost line and setting a new post in a concrete collar designed for expansive soil.
How deep should gate posts be set in Uhrichsville to avoid heaving?
At least 32 inches, and preferably 36. Uhrichsville’s clay soil freezes hard and expands dramatically. A post set at 18 or 24 inches will lift within one freeze-thaw cycle, and we see it every spring. We set all gate posts below the frost line in concrete collars designed for expansive soil. That depth is non-negotiable for anything we install.
Gate Motor & Opener in Uhrichsville
If your gate opener in Uhrichsville is grinding, binding, or just dead, here’s the straight answer: most gate motor problems on the west side of Tuscarawas County come back to one thing, the clay. The same expansive soil that gave Uhrichsville its Clay City nickname and built its brick and tile industry is what heaves gate posts out of plumb every freeze-thaw cycle. That throws the gate leaf out of alignment, which makes the motor strain, trip its entrapment protection, or burn out entirely. Gate Motor & Opener work in Uhrichsville starts with checking the post, not swapping the motor.
Motor Installation
A new gate motor in Uhrichsville is not a plug-and-play job. The motor mounts to whatever the gate is hanging from, and if that post has moved, the new motor inherits the same alignment problem. Our installation starts with checking the post, the hinges if it’s a swing gate, and the rack if it’s a slide gate, then building the operator onto a solid base. A full operator replacement on a swing gate runs about $1,200-$2,200 installed, and slide gate operators run $1,600-$3,000 depending on the gate’s weight, length, and whether the rack is still worth saving.
Motor Repair
Most motor repair calls in Uhrichsville fall into two categories: the motor itself failed, or the gate moved and the motor is paying for it. We diagnose it the same way a mechanic would. We check the limit switches, the capacitor, the gearbox, the control board, and then we back all the way out to the gate leaf and the posts. A gate motor repair in Uhrichsville typically runs $180-$340 when the problem is a capacitor, limit switch, gearbox, or a misaligned gate leaf that just needs resetting.
Linear Motor Service
Linear arm operators, the kind that push and pull a swing gate on a threaded shaft, are everywhere in Uhrichsville because they were common upgrades to gates built in the 1970s and 80s. The weak point we see most: the arm attaches to the gate leaf, and when a clay-heaved post shifts the leaf, the arm binds at the end of its stroke. The motor arm fights a geometry it can’t win. We service linear motors from the major brands, and the fix usually involves realigning the gate first, then adjusting or replacing the arm. Battery backup for an existing opener adds about $300-$600, and intercom integration typically runs $400-$900.
Why does my gate opener work fine all summer but bind every spring in Uhrichsville?
The answer is expansive clay soil, the same geology that gave Uhrichsville its Clay City nickname. All winter the clay that surrounds your gate posts freezes and thaws, heaving them a little more each cycle. By spring the posts are out of plumb, the gate is out of plane, and the opener binds against a gate geometry it was never built to fight. The fix is setting the post below the frost line before touching the motor.
My slide gate motor grinds but won’t move the gate after a hard freeze. Is the motor bad?
Maybe, but just as often the motor is fine and the post footing moved. When clay heaves the post that holds the motor or the one that holds the guide rollers, the rack and pinion lose their mesh and the motor grinds against a bind. We check the footing first, because replacing a motor on a moved post is like putting a new engine in a car with a bent frame. Call (877) 610-2993 and we’ll trace it to the root.
Gate Access Control in Uhrichsville
Gate access control in Uhrichsville typically runs $450-$1,800 for a complete retrofit, with keypad entry starting around $450 and video intercom systems running $1,200-$3,200 depending on the wire run and gate condition. Most jobs are done in one visit because we carry the boards, keypads, and safety photocells on the truck. But here’s what you won’t hear from a catalog: in Uhrichsville, the control board is rarely the real problem. The clay soil under your hinge post is. Gate Access Control that works starts with a gate that moves freely.
Keypad Entry
A keypad that “died” is often a keypad that’s working fine but can’t retract the deadbolt because the gate post twisted during a freeze-thaw cycle. Around Uhrichsville, we start at the post, not the keypad. We install and program wired and wireless keypads, set new codes, and make sure the lock throw and the keypad relay actually line up before we leave. A typical keypad entry system in Uhrichsville runs $450-$900, including the post inspection.
Remote Control Upgrades
Legacy openers with dip-switch remotes are common on the older gates throughout Uhrichsville. We replace outdated receivers with rolling-code units so your remote can’t be cloned by someone with a cheap gadget online. A new receiver and two remotes usually land between $275 and $500, and we program everything on site while the gate is still in your driveway.
Phone and Smart Entry
Phone entry lets you buzz a gate open from your cell, no remote to lose. For Uhrichsville homeowners with side gates and rear driveway gates, a phone-entry retrofit runs $700-$1,400 depending on whether we’re pulling new low-voltage wire or reusing existing conduit. We tie it to a cellular module when there’s no landline at the panel, which is common in the older homes around Uhrichsville. Card readers and smart access start around $600 on an existing operator.
Why does my keypad entry stop working every spring in Uhrichsville?
Because Uhrichsville’s expansive clay soil heaves your gate post over the winter, and by spring the latch and deadbolt no longer line up even though the keypad works fine. The post shifts, the gate leaf tilts, and the deadbolt binds. The fix is resetting the post below the 32-inch frost line with a concrete collar that accounts for clay movement, then re-aiming the latch and programming the keypad. Call (877) 610-2993 for a free look.
My old gate operator has no safety photocells. Is that a code problem in Uhrichsville?
Yes. Current UL 325 standards require entrapment protection on automatic gate operators, and an operator without photocells or an equivalent safety device doesn’t meet modern code. Beyond code, a gate that can’t sense an obstruction is dangerous. We retrofit safety photocells onto older operators, and on most Uhrichsville gates that means mounting the cells to posts that are stable, which on this clay soil often means addressing the post footing first.
Gate Parts & Welding in Uhrichsville
Gate parts and welding in Uhrichsville usually means one of three things: a hinge post that’s heaved out of plumb, a rusted-through rail, or an old operator that’s missing safety sensors. The fix starts with figuring out what the clay soil has done to the post, not just swapping a hinge and hoping. Gate Parts & Welding is how we keep older gates in service rather than sending them to the scrap yard.
Hinge Replacement
A gate sags at the hinge post, not in the middle, and that’s where we start in Uhrichsville. If a 1960s-era swing gate off Eastport Avenue won’t close because the bottom hinge pin is worn to a nub, we’ll cut the old one out, weld a new barrel in place, and rehang the leaf so it swings level. Hinge replacement on a single swing gate typically runs $180 to $340, depending on whether we’re welding a new barrel or replacing the whole hinge assembly. Replacing hinges without checking the post for heave is the quickest way to pay for the same repair twice.
Post Replacement
This is the Uhrichsville specialty, because the clay here doesn’t forgive a shallow footing. We dig or auger down past the 32-inch frost line, pour a concrete collar with a flared base, and set the new steel post where it’ll stay. Post replacement runs $400 to $900 per post, with the footing depth and clay condition driving most of that. If the post is just tilted but still solid at the base, we can sometimes pull it, straighten it, and re-set the same post. Either way, the footing is the job. Fix the panel without the post and you’ll fix it twice.
Custom Welding
When a hinge mount is torn off, an operator arm bracket is sheared, or a latch post needs a custom receiver plate, we weld it on site so the gate never leaves your yard. On-site welding means less downtime, no shipping delay, and a repair that’s sized to the actual steel, not whatever the parts catalog had in stock. Custom welding jobs like a cracked rail or a sheared operator bracket usually land between $150 and $450. That matters on Uhrichsville’s older gates, where nothing is standard anymore.
Why does my swing gate in Uhrichsville sag every spring even after I replaced the hinges?
Because the post under those hinges is heaving in the clay. Uhrichsville sits on expansive marine clay that swells with moisture and freezes through the winter. The post tilts, the gate leaf sags, and new hinges just bend with it. The fix is resetting the post below the 32-inch frost line with a concrete collar that resists the uplift. That’s the Uhrichsville gate repair, and it’s the one that lasts.
Can you weld my original chain-link gate frame back together, or is the steel too far gone?
Usually yes, if there’s enough sound metal left to bite into. We grind off the heavy rust, sleeve or patch the section with fresh galvanized steel, and weld it solid. If the frame is paper-thin through more than a third of its length, we’ll tell you replacement is actually the cheaper answer. We repair first, but we won’t weld a gate that’s going to crack again next winter.
Brands We Service in Uhrichsville
We carry parts and stock for nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common failures, from Linear limit switches to Viking control boards, are on the truck when we pull into your driveway. If we have to order something unusual, turnaround is usually two to three business days because our Cleveland office coordinates daily runs into Tuscarawas County. Our brands page has the full list.
Pricing for Gate Repair in Uhrichsville, OH
| Service | Typical range in Uhrichsville |
|---|---|
| Hinge and post repair | $220-$450 |
| Gate realignment (post sound) | $150-$300 |
| Electric gate repair (limit/safety) | $180 |
| Control board replacement | $400-$600 |
| Pedestrian gate installation | $900-$1,800 |
| Single swing driveway gate with operator | $2,200-$3,400 |
| Double gate with heavy operator | $3,200-$5,200 |
| Swing gate operator replacement | $1,200-$2,200 |
| Slide gate operator replacement | $1,600-$3,000 |
| Gate motor repair | $180-$340 |
| Keypad entry system | $450-$900 |
| Video intercom installation | $1,200-$3,200 |
What pushes price up in Uhrichsville is almost always the soil. If existing post footings are shallow or cracked, we’re excavating and setting new posts with concrete collars designed for expansive clay. That’s real work, and it’s the difference between a gate that lasts 20 years and one that sags again next spring. The price is quoted and agreed before any work starts. You’ll know the number before we turn a wrench, and we don’t pad it at the door.
Neighborhoods We Serve in Uhrichsville
We work all over Uhrichsville and the 44683 ZIP code, from the streets off North Water Street to the neighborhoods around Union Hospital property and the residential blocks near the old clay works. Typical response time across the Uhrichsville area is same-day for most repairs.
- Water Street and surrounding residential blocks
- Neighborhoods near Uhrichsville Elementary
- Homes east of North Main Street
- Properties along the Tuscarawas River corridor
- Residential streets off Trenton Avenue
Service Area - Cities Near Uhrichsville
We run regular service routes throughout Tuscarawas County and into neighboring Stark County. If you’re just outside Uhrichsville, we likely cover your area without a trip charge. We also serve New Philadelphia, OH, Dover, OH, North Canton, OH, Canton, OH, and Massillon, OH. Dispatch and scheduling are coordinated from our Cleveland office, but the crew that shows up at your gate is local to this area.
Serving Uhrichsville, OH - Our Local Coverage Area
Gatewood Fence & Gate crews serve Uhrichsville and the communities around it; dispatch is coordinated from our Cleveland office. The map shows the Uhrichsville coverage area; if your address is on it, we can help.
Also serving nearby: Uhrichsville, OH, New Philadelphia, OH, Dover, OH, North Canton, OH, Canton, OH, Massillon, OH.
FAQs About Gate Repair in Uhrichsville
Most repairs in Uhrichsville are scheduled same-day or next-day, and a live person answers the phone 24 hours a day. If your gate is stuck open or blocking your driveway, we’ll get someone there as fast as we can. Call (877) 610-2993 any time.
Tuscarawas County generally does not require a permit for a residential gate replacement on existing posts, but new driveway gates that extend into the right-of-way or include electrical work may need review. We check local requirements before we start, and we handle any paperwork that applies to your specific job.
Yes, estimates are free, and we also offer a free second opinion on any written estimate you bring us from another company. We’ll look at your gate, tell you what we see, and quote a price that doesn’t change at the door. Seniors and veterans get a permanent 10% discount, and we take $40 off any repair over $200.
Call (877) 610-2993 today for a free estimate on any gate repair, installation, or welding job in Uhrichsville. A live person will answer, day or night, and we’ll get you scheduled.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Uhrichsville Customers Say
"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"He builds the gates himself in his own shop. You can go and look at it. That is not something you can say about the outfits that just order a panel in."
- Doreen Whitfield