Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Quincy, MA
Most gate repairs in Quincy run $180 to $340 for hinge and latch work, and we can usually get to you same-day or next-morning when you call early. The salt air off Quincy Bay and the granite ledge sitting a foot under your topsoil make Quincy gates fail differently than gates in Milton or Braintree. We’re in every Quincy ZIP from 02169 through 02269, and the person who answers at (877) 610-2993 is the person who will show up. Hal Gatewood has been at this since 2001, and his name is on the shop, the invoice, and the work.
Why Quincy Homes Are Different
Quincy sits directly on Quincy Bay, and that salt air doesn’t stop at the shoreline. Homes within a few blocks of Wollaston Beach or Marina Bay see steel gate hardware corrode far faster than in inland Norfolk County towns. Hinges seize, springs snap, and post bases rust through at the collar. A galvanized steel gate that would last twenty years in Braintree shows rust-through at the bottom rail in under a decade of salt spray.
Then there’s the granite. Quincy is literally built on the same bedrock that fueled its nineteenth-century quarrying industry. That ledge sits one to two feet under the topsoil in much of the city, especially Squantum, the higher streets off Hancock Street, and anywhere you see rock outcroppings in the neighborhood. When frost heaves a gate post out of alignment, a standard post-hole digger hits solid stone before you reach proper depth. That means core drilling or anchoring systems, not deeper digging, and it’s a site condition that catches plenty of out-of-town gate techs by surprise.
The housing stock matters too. Quincy’s neighborhoods are packed with early-to-mid twentieth-century triple-deckers and two-family colonials, many with original 1950s to 1970s galvanized chain-link or ornamental iron side-yard gates that are corroding at the post collars and hinge plates. They’re functional but well past their designed service life, and the narrow driveways in Germantown and South Quincy leave no margin for a gate that sags or drags.
Gate Repair in Quincy
Gate repair in Quincy means dealing with two things most of the South Shore doesn’t have: salt air off Quincy Bay and granite ledge sitting anywhere from twelve to twenty-four inches under your feet. A gate that binds or sags here isn’t just a nuisance, it’s a security gap and a daily wrestling match. We cover every Quincy ZIP from 02169 up to 02269, and the person who answers the phone is the person who will handle your job. Gate Repair is what we built this company on, and we still do it the same way Hal did in 2001: look at the gate, find the real problem, quote it straight, and fix it right.
Hinge & Post Repair
This is where most Quincy gates actually fail. A gate sags in the hinge post, not in the middle, and fixing the panel without addressing the post means you’ll fix it twice. In Quincy we regularly find hinge posts set in concrete at eighteen inches because the original installer hit ledge before frost depth. That shallow footing heaves every winter. We core-drill into the granite or use shallow-footing anchoring systems so the post stays plumb instead of tilting each spring. A basic hinge replacement or gate realignment typically runs $180 to $340, while post repair or replacement with core drilling into ledge runs $320 to $640 depending on how much anchor work the granite requires.
Electric Gate Repair
Electric gates in Quincy take a beating from salt-laden air, especially anywhere within a few blocks of Wollaston Beach or Marina Bay. Operators that should last a decade inland often show rust-through at brackets and connector points in eight years or less. We diagnose on site: power supply, limit switches, circuit board, safety photo eyes. If the operator is salvageable, we repair it. If it’s not, we tell you straight and quote a replacement before any work starts. Electric operator repair runs $240 to $520 for limit switches, boards, or arm replacement.
Automatic Gate Repair
Automatic gate operators in Quincy fail in predictable ways: salt corrosion on the rack and pinion bracket, limit switches that stick after wet winters, and stripped drive gears from gates forced against storm winds. We service LiftMaster, FAAC, Linear, Viking, DoorKing, and Ghost Controls. The repair-first philosophy applies here too. We won’t sell you a new board when a limit switch reset and a cleaned terminal block fixes the problem. Weld and rust repair on ornamental iron runs $150 to $400 per section.
Why does my gate in Wollaston rust so much faster than my cousin’s in Braintree?
Salt air off Quincy Bay. Wollaston sits directly on the harbor, and airborne salt coats every metal surface. Standard galvanized steel that lasts twenty years inland shows rust-through at the bottom rail and hinge post collar in eight to ten years in 02170. We spec corrosion-resistant hardware on every waterfront job. Call (877) 610-2993 for an exact quote - estimates are free.
My gate post is loose every spring - is that normal in Quincy?
It’s common, but it’s not something you should live with. Quincy sits on granite ledge so shallow that many original posts were set at eighteen inches or less, well above frost depth. Every freeze-thaw cycle heaves the footing, and the post leans a little more each year. We core-drill into the bedrock or use shallow-footing anchoring systems to set the post so it stays plumb. Call (877) 610-2993 and we’ll take a look - no trip charge inside the county.
Gate Installation in Quincy
Gate installation in Quincy costs between $1,850 and $7,400 for most residential projects, with driveway gates running higher than pedestrian gates. We’re in Quincy every week, handling installations from Germantown to Squantum, and we know exactly what salt air and granite ledge do to gate posts around here. Gate Installation is measured, ordered, and scheduled - we don’t promise same-day, but we do promise a free measure and a written price that doesn’t change at the door.
Driveway Gate Installation
Driveway gates in Quincy typically run $3,200 to $7,400 installed, depending on width, automation, and whether we’re anchoring into bedrock or setting posts in soil. Many Quincy homes have narrow side-drive access between triple-deckers, so we regularly build custom-width double gates that fold or slide back against the house rather than swinging into the neighbor’s yard. A gate sags in the hinge post, not in the middle, and that’s where we start.
Pedestrian Gate Installation
Pedestrian gates for Quincy yards and side entries usually run $1,850 to $3,100. Salt air chews through cheap gate hardware fast in Germantown and anywhere near the water, so we spec stainless or heavy-gauge galvanized hinges and latches as standard, not as an upsell. These small gates get ignored until the latch stops lining up, and by then the post collar is usually rusted through.
Sliding Gate Installation
Sliding gates suit Quincy lots where a swing gate can’t clear the slope or where snowbanks make swinging impractical. Expect $4,200 to $7,600 for a motorized sliding driveway gate. Quincy’s freeze-thaw pushes posts out of alignment every few winters, so we build sliding gate tracks on reinforced ground rails and set the carrier posts deeper than standard specs. The granite ledge that runs under the city solves one problem and creates another: we often core into rock rather than fight it with a post auger.
Why is gate installation more expensive in Quincy than in Milton or Braintree?
It isn’t always, but coastal homes in Quincy often need more expensive hardware than inland suburbs. Salt air along Wollaston Beach and Marina Bay forces us to use aluminum frames or marine-grade stainless hardware that a Braintree homeowner may not need. Plus, core drilling into Quincy’s granite bedrock adds labor that doesn’t exist in towns with deeper soil. The difference is usually a few hundred dollars, not thousands. Call (877) 610-2993 for a free measure and written quote.
How quickly can you get to Quincy for a gate installation estimate?
We can usually get to Quincy for a free measure and written quote within two to five business days. Installation scheduling depends on whether we need to order custom hardware or fabricate anything, but we will give you a firm date when we quote. No trip charge inside the county, and every job carries our 90-Day Done Right Promise in writing.
Gate Motor & Opener in Quincy
Gate motor and opener repair in Quincy usually runs between $185 and $520 depending on whether we’re replacing a control board, a limit switch, or the full operator arm. Most Quincy calls are same-day or next-morning, and we stock the common LiftMaster, FAAC, and Linear parts on the truck so we’re not driving back and forth across the Neponset Bridge all day. Gate Motor & Opener service is what we do when your gate is stuck open on Wollaston Beach Boulevard or the motor just hums and won’t move.
Motor Installation
A new gate motor installation in Quincy typically runs $950 to $2,400 installed, including the operator, mounting hardware, safety sensors, and the electrical hookup. On heavier steel driveway gates or anything within a few blocks of Wollaston Beach, we’ll recommend a duty-rated operator so the salt air and coastal wind load don’t kill a light-duty residential motor inside three years. We also handle the concrete pad or post mounting, and on Quincy properties where the granite ledge sits shallow, that sometimes means core drilling into rock instead of digging a standard footing.
Motor Repair
Motor repair in Quincy averages $185 to $480. That covers the most common failures we see: dead control boards, stripped gears, burned capacitors, failed limit switches, and corroded wire terminals. A lot of the time the motor itself is fine and the problem is a control board that got eaten by salt air or a gearbox that stripped because a frost-heaved post made the gate bind every winter. We diagnose the actual fault, show you what’s wrong, and give you the number before we start.
Linear Motor
Linear motor operators are common on Quincy’s older side-yard gates and two-family driveway gates. We repair and replace Linear-brand operators regularly, including the older actuator arm setups that chain-link gates from the 1970s still use. The big issue on linear operators in Quincy is salt corrosion at the arm extension joint and the wiring block. We stock Linear arm assemblies and control boards locally, so we don’t have to order for a week when your gate won’t open at all.
Why does my gate opener motor corrode so fast near Wollaston Beach?
Salt air from Quincy Bay gets into the control board, the limit switch contacts, and the wiring terminals, and it corrodes them far faster than inland air ever would. On streets within a few blocks of Wollaston Beach or the Squantum peninsula, we regularly replace control boards on openers that are only six to ten years old because the salt has eaten the traces. The fix is a new sealed enclosure, not just the board. Call (877) 610-2993 for a diagnosis - estimates are free.
My 1970s chain-link driveway gate sags and the motor struggles. Is it worth fixing the operator or the gate first?
Fix the gate first. A sagging gate binds against the hinges and the frame, and that mechanical load strips the operator’s gearbox. No motor will survive long against a gate that’s fighting itself. A lot of older Quincy chain-link gates sag because the hinge post rusted through at the collar or the post moved off plumb from frost. We can weld or reset the post, realign the frame, and then match the operator to a gate that actually moves freely. Call (877) 610-2993 and we’ll sort out which problem came first.
Gate Access Control in Quincy
Gate access control in Quincy means keypads, remotes, phone entry, card readers, and video intercoms that have to hold up to salt air and granite ledge. We service and install all of it. The average keypad or intercom repair in Quincy runs $220 to $480, and most jobs we can schedule within one to two business days. Gate Access Control is how you stop getting out of your car in a rainstorm, and it’s how landlords in Germantown’s triple-deckers stop rekeying every six months.
Keypad Entry
Quincy keypads fail in predictable ways. The most common is corrosion at the wiring terminals behind the keypad body, especially within two miles of Quincy Bay. Moisture and salt wick up the wire, turn the copper green, and the keypad stops sending the signal. We replace the terminal block, seal the back plate, and use stainless hardware. In Squantum and Marina Bay especially, standard galvanized screws are a mistake - they rust through in a few years, and we don’t use them. A keypad replacement runs $220 to $410 installed depending on brand and whether we’re reusing the existing post.
Remote Control
When a remote stops opening a gate in Quincy, people assume the battery. It’s sometimes worse than that. Salt air gets into the receiver board inside the gate operator, especially on older Viking and LiftMaster units. The exposed antenna terminals tarnish and the receiver’s sensitivity drops until the remote only works from ten feet away. We test the receiver with a meter, reterminate the antenna connection, and replace the board only when it’s actually dead. A remote for most gate operator brands in Quincy runs $45 to $135 installed.
Phone Entry
Phone entry systems for Quincy gates are popular in the triple-decker neighborhoods, where renters cycle in and out and landlords don’t want to issue a keypad code to every new tenant. The phone entry unit usually lives on a bollard or post beside the gate. Here’s the Quincy problem: granite ledge sits eighteen to thirty inches down in most of the city. A standard post-hole digger hits solid rock before the post is deep enough to survive a winter. We core drill when we have to, and when we can’t, we surface-mount on a reinforced pad that won’t tilt after the first freeze-thaw. A phone entry or card reader system runs $350 to $750 for typical single-family driveway access.
Why do keypad entry panels on Quincy gates stop working after a few winters, even when the keypad itself is new?
Because the panel was installed with the wrong hardware and no weather sealing at the back plate. In Quincy, moisture and salt-laden air wick up inside the keypad body and corrode the terminals. A new keypad on corroded wire or a rusted post will fail in two winters. We replace the terminal block, use stainless hardware, seal the back plate, and it lasts. Call (877) 610-2993 for an exact quote - estimates are free.
Does Quincy’s granite bedrock make it harder to add a card reader or keypad bollard next to an existing gate?
Yes, granite ledge often lies eighteen to thirty inches below grade in much of Quincy, which is too shallow for standard post depth. We core drill into the ledge or surface-mount on a reinforced pad. It adds some labor cost, usually $150 to $300 on a typical job, but it’s the difference between a bollard that tilts in a year and one that stays straight. Call (877) 610-2993 for a free measure and written quote.
Gate Parts & Welding in Quincy
If your gate is sagging, seized, or rusting through anywhere in Quincy, we can usually get a welder to your driveway the same day. We carry the hinge parts, post anchors, and welding equipment needed to repair what salt air and granite ledge have done to your gate. Gate Parts & Welding is where we fix what other companies want to replace, and we do it in your driveway, not in someone else’s shop.
Hinge Replacement
Near Quincy Bay, hinge plates and hinge pins are the first parts to go. Salt spray works into the threads, eats the zinc coating, and before long the gate is dragging on the latch side. We stock stainless steel hinge kits specifically for coastal exposure, and we can usually swap a corroded hinge in under two hours. If the hinge post is also compromised, we address that in the same visit. Fix the panel without the post and you’ll fix it twice. A single-gate hinge replacement runs $180 to $340 including parts and labor; double gates with both panels run $320 to $590.
Post Replacement
Post replacement in Quincy is different from post replacement in Braintree or Milton, and here’s why: you hit granite ledge within a foot or two of the surface. That’s the same stone that kept Quincy’s quarries busy in the 1800s. Standard post-hole digging stops dead at the rock, and the correct repair is a core-drilled anchor or a fabricated base plate pinned to the ledge. We have the drilling equipment and the welding rig to do that on site, which is why we’re the crew other companies call when they’ve hit rock and don’t know what to do. Post replacement with granite ledge anchor runs $480 to $900 per post, including core drilling if needed.
Custom Welding
Sometimes the part you need doesn’t exist. Maybe the gate is a 1970s custom iron job from a shop that’s been gone for decades. Maybe a previous owner welded on a hanger that was never quite right. We fabricate brackets, reinforcements, and replacement sections in the truck and on site. If the repair needs a heavier section of steel or a stainless replacement part, we can usually have it cut, shaped, and welded the same day. Custom welding fabrication on site runs $140 to $260 per hour, plus materials.
Can you weld a broken hinge on a salt-corroded gate, or does the whole post need replacing?
It depends on how much steel is left around the hinge, but in many Quincy cases we can cut out the corroded section, weld in a new plate, and save the post. We recently rebuilt a hinge post on a 1960s ornamental iron swing gate off Quincy Shore Drive in Wollaston. The bottom hinge plate had rusted through from decades of salt air, pulling the post out of alignment. We core-drilled a new anchor into the ledge, welded a replacement plate, and realigned the gate. Call (877) 610-2993 for an exact quote - estimates are free.
Do you need to core drill into granite ledge for every gate post in Quincy?
No. Some yards in Quincy have enough topsoil to set a standard post depth before hitting rock, particularly in the flatter sections of Wollaston and North Quincy. But across much of Quincy, especially the Squantum peninsula, the higher streets off Hancock Street, and anywhere you see ledge outcroppings in the neighborhood, you’re likely to hit granite within a foot or two. We bring the core-drilling equipment on every post replacement call, so we’re ready either way. Call (877) 610-2993 and we’ll assess your site.
Brands We Service in Quincy
We carry parts and stock for nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common repairs on Linear, Viking, and Ghost Controls units we can complete same-day because the parts are on the truck. For boards or specialty components we don’t have in Quincy, our Boston office coordinates next-morning delivery so you’re not waiting a week for a gate that won’t close. our brands
Pricing for Gate Repair in Quincy, MA
| Service | Typical range in Quincy |
|---|---|
| Single-gate hinge replacement / realignment | $180 - $340 |
| Double-gate hinge replacement (both panels) | $320 - $590 |
| Post repair / replacement with ledge anchor | $320 - $640 |
| Post replacement with core drilling (per post) | $480 - $900 |
| Bottom rail weld repair | $220 - $410 |
| Electric operator repair (limit switch, board, arm) | $240 - $520 |
| Ornamental iron weld / rust repair (per section) | $150 - $400 |
| Keypad replacement (installed) | $220 - $410 |
| Remote control replacement (installed) | $45 - $135 |
| Phone entry / card reader system | $350 - $750 |
| Custom welding fabrication (per hour + materials) | $140 - $260 |
| New gate motor installation (including safety sensors) | $950 - $2,400 |
What pushes price up in Quincy specifically: proximity to the bay means we spec marine-grade or stainless hardware instead of standard steel, and shallow granite ledge often requires core drilling or anchoring systems that don’t exist in deeper-soil towns. Every price is quoted and agreed in writing before any work starts. The number we give you is the number on the invoice.
Neighborhoods We Serve in Quincy
We work across Quincy, from the waterfront at Marina Bay up through Wollaston, Germantown, Quincy Center, and South Quincy. Typical response for a repair call in any of these neighborhoods is same-day or next-day when you call in the morning. Scheduling and dispatch are coordinated from our Boston office, but the crew that shows up knows these streets and these conditions.
- Marina Bay
- Wollaston
- Squantum
- Germantown
- South Quincy
Service Area - Cities Near Quincy
We cover Quincy and the surrounding communities without a trip charge inside the county. If you’re near the city line, we also work in Milton, MA, Weymouth, MA, Braintree, MA, South Boston, MA, and Jamaica Plain, MA. Each town has its own conditions - Milton’s deeper soil, Braintree’s inland air, South Boston’s tighter lots - and we adjust the work to match.
Serving Quincy, MA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Quincy and the communities around it; dispatch is coordinated from our Boston office. The map shows the Quincy coverage area; if your address is on it, we can help.
Also serving nearby: Quincy, MA, Milton, MA, Weymouth, MA, Braintree, MA, South Boston, MA, Jamaica Plain, MA.
FAQs About Gate Repair in Quincy
Most repair calls in Quincy are same-day or next-morning if you call early. Installation estimates are scheduled within two to five business days. A live person answers at (877) 610-2993 twenty-four hours a day, and we’ll give you a real window, not a four-hour wait.
Quincy requires permits for new gate installations and for any work that modifies the fence line or adds electrical service. Simple repairs to existing gates - hinge replacement, motor repair, welding - usually don’t trigger permitting. We know the Quincy Building Department’s requirements and will tell you upfront if your job needs a permit, then handle the paperwork if it does.
Yes. Every motorized gate installation we do in Quincy includes the operator, mounting hardware, safety photo eyes or edge sensors, and the low-voltage wiring from the operator to the control point. If your driveway needs a new power run from the house, we coordinate that too. The safety edges aren’t optional - they’re required, and we don’t leave until they’re tested and working.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Quincy Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"The fence is excellent and it was fairly priced. He is not quick to answer email, so if you need him, ring. He always picks up the phone."
- Rodney Falkenrath